Abstract:In forest areas, when using interferometric synthetic aperture radar (InSAR) technique to extract subcanopy topography, a key problem is how to reduce the impact of the forest-scattering process on InSAR height measurements. In this paper, we propose a new methodology for subcanopy topography extraction by making full use of single-baseline TanDEM-X InSAR data. The interferometric phase is used to estimate a high-resolution and high-precision digital elevation model (DEM), and the coherence magnitude is used to extract the scattering phase center (SPC) height associated with canopy scattering. Allowing for the difference in the sensitivity of TanDEM-X bistatic interferometry information for forests with different densities, two scenarios are involved: (1) For pixels characterized by dense forest, the X-band SAR signal cannot penetrate through the forest canopy layer. In this case, an existing scattering model is used to estimate the InSAR penetration depth from the coherence magnitude. Note that when the penetration depth is small compared with the height of ambiguity (HoA), the former can be recognized as the difference between the InSAR DEM and the actual surface height. Some sparse forest heights (or SPC heights) measured by the Ice, Cloud, and land Elevation Satellite-2 (ICESAT-2) system are then used to help determine the linear relationship between penetration depth and sparse forest height (or SPC height). Finally the SPC can be estimated and removed from the TanDEM-X InSAR DEM. (2) For pixels characterized by sparse vegetation, the X-band likely penetrates the vegetation volume layer to ground level. For this scenario, a coherence threshold is set to identify these pixels, and the corresponding SPC heights can be considered zero where the subcanopy topography is approximately equal to the InSAR-generated DEM. The proposed method was validated by combining TanDEM-X coregistered single look slant range complex (CoSSC) data from two test sites with different forest types with ICESAT-2 points. The results are as follows. For the Krycklan test site, compared with the validation data, the RMSE varied from 7.76 m for the InSAR DEM to 3.22 m for the reconstructed subcanopy topography, which is an improvement of 58.5%. For the Oyan test site, subcanopy topography achieved an RMSE of 7.26 m compared with the RMSE of 27.12 m before SPC height correction, which represents an improvement of 80.1%. In addition, we investigated the impact of the topographic slope and the necessity of using the coherence threshold. For inconsistencies between TanDEM-X bistatic InSAR data and ICESAT-2 measured forest height over time, the fitting between penetration depth and SPC height calculated by ICESAT-2 subcanopy topographic elevation and InSAR-generated DEM can be used. These investigations confirm the feasibility and reliability of the proposed method.

Forest Height Inversion by Combining Single-Baseline TanDEM-X InSAR Data with External DTM Data

Estimation of Canopy Height From a Multi-SINC Model in Mediterranean Forest With Single-Baseline TanDEM-X InSAR Data

Forest Height Inversion with Single-Baseline TanDEM-X InSAR Coherence

Simultaneous Estimation of Sub-canopy Topography and Forest Height with Single-baseline Single-polarization TanDEM-X Interferometric Data Combined with ICESat-2 Data

Forest Height Estimation Approach Combining P-Band and X-Band Interferometric SAR Data

Forest Height Estimaton in Mountainous Terrain Using Ascending and Descending Tandem-X Data

An adaptive directional model for estimating vegetation canopy height using space-borne photon counting laser altimetry data

Estimation of subcanopy topography based on single-baseline TanDEM-X InSAR data

Canopy Height Estimation in Mediterranean Forests of Spain with TanDEM-X Data

Automated Estimation of Forest Height and Underlying Topography over a Brazilian Tropical Forest with Single-Baseline Single-Polarization TanDEM-X SAR Interferometry

Digital terrain, surface, and canopy height model generation with dual-baseline low-frequency InSAR over forest areas

Mapping Large-Scale Forest Height by Integrating Tandem-X and Multi-Source Remote Sensing Data: a Case Study of Spain

Automated Estimation of Sub-Canopy Topography Combined with Single-Baseline Single-Polarization TanDEM-X InSAR and ICESat-2 Data

Tropical Forest Height and Underlying Topography from Tandem-X SAR Interferometry

Large-Scale Forest Height Mapping from TanDEM-X, ICESat-2 and Landsat 8 Data Using a Machine-Learning Method

Forest Canopy Height Estimation Combining Dual-Polarization PolSAR and Spaceborne LiDAR Data

Sub-Canopy Topography Estimation from TanDEM-X DEM by Fusing ALOS-2 PARSAR-2 InSAR Coherence and GEDI Data.

Improved Forest Height Mapping Using Multibaseline Low-Frequency PolInSAR Data Based on Effective Selection of Dual-Baseline Combinations

A TSVD-Based Method for Forest Height Inversion from Single-Baseline PolInSAR Data

High-resolution Sub-Canopy Topography Mapping Via TanDEM-X DEM Combined with Future P-band BIOMASS PolInSAR Data

A Multi-Baseline Forest Height Estimation Method Combining Analytic and Geometric Expression of the RVoG Model