NiMn2O4 as an efficient cathode catalyst for rechargeable lithium–air batteries

Shuling Li,Jin Xu,Zhong Ma,Shiming Zhang,Xiufang Wen,Xuebin Yu,Jun Yang,Zi-Feng Ma,Xianxia Yuan

DOI: https://doi.org/10.1039/c7cc01995e

IF: 4.9

2017-01-01

Chemical Communications

Abstract:Intermediate spinel structured NiMn2O4-FT performs better than normal spinel oxide NiMn2O4-PH as a cathode bi-functional catalyst for Li–air batteries.

What problem does this paper attempt to address?

Nimn2o4 As An Efficient Cathode Catalyst For Rechargeable Lithium-Air Batteries

Shuling Li,Jin Xu,Zhong Ma,Shiming Zhang,Xiufang Wen,Xuebin Yu,Jun Yang,Zi-Feng Ma,Xianxia Yuan

DOI: https://doi.org/10.1039/c7cc01995e

IF: 4.9

2017-01-01

Chemical Communications

Abstract:NiMn2O4 with different crystal structures was successfully synthesized and evaluated as a cathode catalyst for rechargeable Li-air batteries for the first time. The result reveals that the intermediate spinel structure between normal and inverse spinels demonstrates faster kinetics towards ORR/OER than the normal spinel, leading to a better battery performance.
Radially Oriented Single‐Crystal Primary Nanosheets Enable Ultrahigh Rate and Cycling Properties of LiNi0.8Co0.1Mn0.1O2 Cathode Material for Lithium‐Ion Batteries

Xing Xu,Hua Huo,Jiyuan Jian,Liguang Wang,He Zhu,Sheng Xu,Xiaoshu He,Geping Yin,Chunyu Du,Xueliang Sun

DOI: https://doi.org/10.1002/aenm.201803963

IF: 27.8

2019-01-01

Advanced Energy Materials

Abstract:Ni-rich Li[NixCoyMn1-x-y]O-2 (x >= 0.8) layered oxides are the most promising cathode materials for lithium-ion batteries due to their high reversible capacity of over 200 mAh g(-1). Unfortunately, the anisotropic properties associated with the alpha-NaFeO2 structured crystal grains result in poor rate capability and insufficient cycle life. To address these issues, a micrometer-sized Ni-rich LiNi0.8Co0.1Mn0.1O2 secondary cathode material consisting of radially aligned single-crystal primary particles is proposed and synthesized. Concomitant with this unique crystallographic texture, all the exposed surfaces are active {010} facets, and 3D Li+ ion diffusion channels penetrate straightforwardly from surface to center, remarkably improving the Li+ diffusion coefficient. Moreover, coordinated charge-discharge volume change upon cycling is achieved by the consistent crystal orientation, significantly alleviating the volume-change-induced intergrain stress. Accordingly, this material delivers superior reversible capacity (203.4 mAh g(-1) at 3.0-4.3 V) and rate capability (152.7 mAh g(-1) at a current density of 1000 mA g(-1)). Further, this structure demonstrates excellent cycling stability without any degradation after 300 cycles. The anisotropic morphology modulation provides a simple, efficient, and scalable way to boost the performance and applicability of Ni-rich layered oxide cathode materials.
Spinel NiCo2S4 As Excellent Bi-Functional Cathode Catalysts for Rechargeable Li-O-2 Batteries

Mengting Xu,Xiaoyan Hou,Xuebin Yu,Zi-Feng Ma,Jun Yang,Xianxia Yuan

DOI: https://doi.org/10.1149/2.1151906jes

IF: 3.9

2019-01-01

Journal of The Electrochemical Society

Abstract:Developing bi-functional catalyst is an effective way to improve the kinetics of oxygen electrochemistry and promote the performance of Li-O-2 batteries. In this study, spinel NiCo2S4 with urchin-like and yolk-shell morphologies were successfully synthesized and evaluated as cathode catalysts for rechargeable Li-O-2 batteries. The results demonstrate both NiCo2S4 materials are catalytically active toward ORR/OER, but the urchin-like NiCo2S4 performs better with faster kinetics, higher capacity, lower polarization and longer cycle life. Moreover, cycling performance of the Li-O-2 batteries with urchin-like NiCo2S4 is evidently better than the reported data in literatures for the batteries with many other transition metal sulfides. (c) 2019 The Electrochemical Society.
Spinel LiNixMn2-xO4 as cathode material for aqueous rechargeable lithium batteries

Faxing Wang,Shiying Xiao,Yi Shi,Lili Liu,Yusong Zhu,Yuping Wu,Jiazhao Wang,Rudolf Holze

DOI: https://doi.org/10.1016/j.electacta.2013.01.106

IF: 6.6

2013-01-01

Electrochimica Acta

Abstract:Ni-doped spinel LiNixMn2−xO4 (x=0, 0.05, 0.10) samples were prepared by a sol–gel method. Structure and morphology of the samples were characterized by X-ray diffraction, scanning electron microscopy, Brunnauer–Emmet–Teller method and inductively coupled plasma atomic absorption spectrometry. The electrochemical behavior as a cathode material (positive mass) for aqueous rechargeable lithium batteries (ARLBs) was investigated by cyclic voltammetry, electrochemical impedance spectroscopy, capacity measurements and cycling tests. The results show that the LiNi0.1Mn1.9O4 electrode presents the best rate and cycling performance but low reversible capacity. In contrast, the LiNi0.05Mn1.95O4 electrode shows a higher reversible capacity and relatively good cycling behavior. At a current density of 150mAg−1, LiNi0.05Mn1.95O4 delivers a reversible capacity of 102mAhg−1. At the relative high current densities of 1500 and 3000mAg−1, the LiNi0.05Mn1.95O4 electrode still delivers reversible capacities of 95.0 and 88.7mAhg−1, respectively. The Ni-doped samples show excellent cycling life in 0.5molL−1 Li2SO4 aqueous solution. The capacity retention ratios for LiNi0.05Mn1.95O4 and LiNi0.10Mn1.90O4 after 800 cycles at a current density of 1500mAg−1 are 79.4% and 91.1%, respectively, much higher than that for the undoped LiMn2O4 at only 37.8%.
Facile synthesis of spinel CuCo2O4 nanocrystals as high-performance cathode catalysts for rechargeable Li-air batteries.

Ying Liu,Lu-Jie Cao,Chen-Wei Cao,Man Wang,Kwan-Lan Leung,Shan-Shan Zeng,T F Hung,C Y Chung,Zhou-Guang Lu

DOI: https://doi.org/10.1039/c4cc04682j

IF: 4.9

2014-01-01

Chemical Communications

Abstract:CuCo2O4 nanoparticles have been synthesized by a simple and low-cost urea combustion method and characterized as bifunctional catalysts for non-aqueous Li-air batteries. The resulting CuCo2O4 catalyst has been demonstrated to effectively reduce the charge-discharge polarization of Li-air batteries in a simulated air environment (80% Ar : 20% O-2).
Ternary Spinel MCo2O4 (M = Mn, Fe, Ni, and Zn) Porous Nanorods as Bifunctional Cathode Materials for Lithium-O2 Batteries

Saad Gomaa Mohamed,Yuan-Quei Tsai,Chih-Jung Chen,Yi-Ting Tsai,Tai-Feng Hung,Wen-Sheng Chang,Ru-Shi Liu

DOI: https://doi.org/10.1021/acsami.5b02180

2015-06-10

Abstract:The development of Li-O2 battery electrocatalysts has been extensively explored recently. The Co3O4 oxide has attracted much attention because of its bifunctional activity and high abundance. In the present study, toxic Co(2+) has been replaced through the substitution on the tetrahedral spinel A site ions with environmental friendly metals (Mn(2+), Fe(2+), Ni(2+), and Zn(2+)), and porous nanorod structure are formed. Among these spinel MCo2O4 cathodes, the FeCo2O4 surface has the highest Co(3+) ratio. Thus, oxygen can be easily adsorbed onto the active sites. In addition, Fe(2+) in the tetrahedral site can easily release electrons to reduce oxygen and oxidize to half electron filled Fe(3+). The FeCo2O4 cathode exhibits the highest discharging plateau and lowest charging plateau as shown by the charge-discharge profile. Moreover, the porous FeCo2O4 nanorods can also facilitate achieving high capacity and good cycling performance, which are beneficial for O2 diffusion channels and Li2O2 formation/decomposition pathways.
Electrochemical Performance Ni Doped Spinel LiMn2O4 Cathode for Lithium Ion Batteries

Cui YongLi,Bao WenJing,Yuan Zheng,Zhuang QuanChao,Sun Zhi

DOI: https://doi.org/10.4028/www.scientific.net/amr.347-353.290

2011-01-01

Advanced Materials Research

Abstract:LiNixMn2-xO4 (x=0, 0.05, 0.1, 0.2, 0.3, 0.4, 0.5) compounds with spinel crystal structure are synthesized by sol-gel method. The dependence of the physicochemical properties of these compounds has been extensively investigated by using X-ray diffraction (XRD), scanning electron microscope (SEM), cyclic voltammogram (CV) and charge-discharge test. It is found that as Mn is replaced by Ni, the initial capacity decreases, but the capacity retention is enhanced. Of all the LiNixMn2-xO4 (x=0, 0.05, 0.1, 0.2, 0.3, 0.4) compounds, the LiNi0.2Mn1.8O4 has best electrochemical performance, about 120mAhg-1 discharge capacity, its capacity retention rate of 96.6% after 100 cycles. However the LiNi0.5Mn1.5O4 sample shows excellent electrochemical performance at 4.7 V high potential, 150 mAhg-1 discharge capacity, above 110 mAhg-1 of capacity retention after 42 cycles of charge/discharge. The prepared LiNi0.5Mn1.5O4 powders sintered at 750 °C here has Fd3m space group.
Efficient and Durable Bifunctional Oxygen Catalysts Based on NiFeO@MnOx Core-Shell Structures for Rechargeable Zn-Air Batteries

Yi Cheng,Shuo Dou,Jean-Pierre Veder,Shuangyin Wang,Martin Saunders,San Ping Jiang

DOI: https://doi.org/10.1021/acsami.6b16180

2017-03-08

Abstract:Rechargeable Zn-air battery is limited by the sluggish kinetics and poor durability of the oxygen catalysts. In this Research Article, a new bifunctional oxygen catalyst has been developed through embedding the ultrafine NiFeO nanoparticles (NPs) in a porous amorphous MnOx layer, in which the NiFeO-core contributes to the high activity for the oxygen evolution reaction (OER) and the amorphous MnOx-shell functions as active phase for the oxygen reduction reaction (ORR), promoted by the synergistic effect between the NiFeO core and MnOx shell. The synergistic effect is related to the electron drawing of NiFeO core from MnOx shell, which decreases the affinity and adsorption energy of oxygen on MnOx shell and significantly increases the kinetics of ORR. The electrocatalytic activity and durability of NiFeO@MnOx depends strongly on the NiFeO:MnOx ratio. NiFeO@MnOx with NiFeO:MnOx weight ratio of 1:0.8 shows the best performance for reversible ORR and OER, with a potential gap (ΔE) of 0.792 V to achieve a current density of 3 mA cm-2 for ORR (EORR=3) and 5 mA cm-2 for OER (EOER=5) in 0.1 M KOH solution. The high activity of the NiFeO@MnOx(1:0.8) has been demonstrated in a Zn-air battery. Zn-air battery fabricated using the NiFeO@MnOx(1:0.8) oxygen electrode shows similar initial performance with that of Pt-Ir/C oxygen electrode but a much better durability under charge and discharge cycles as the result of the structure confinement effect of amorphous MnOx. The results demonstrate NiFeO@MnOx as an effective bifunctional oxygen catalysts for rechargeable metal-air batteries.
Molybdenum Nitride/N-Doped Carbon Nanospheres for Lithium-O-2 Battery Cathode Electrocatalyst

Kejun Zhang,Lixue Zhang,Xiao Chen,Xiang He,Xiaogang Wang,Shanmu Dong,Lin Gu,Zhihong Liu,Changshui Huang,Guanglei Cui

DOI: https://doi.org/10.1021/am400209u

IF: 9.5

2013-01-01

ACS Applied Materials & Interfaces

Abstract:Molybdenum nitride/N-doped carbon nanospheres (MoN/N-C) are synthesized by hydrothermal method followed by ammonia annealing. The as-prepared MoN/N-C nanospheres manifest considerable electrocatalytic activity toward oxygen reduction reaction in nonaqueous electrolytes because of its nanostructure and the synergetic effect between MoN and N-C. Furthermore, the MoN/N-C nanospheres are explored as cathode catalyst for Li-O-2 batteries with tetra-(ethylene glycol) dimethyl ether as the electrolyte. The assembled batteries deliver alleviated overpotentials and improved battery lifespan, and their excellent performances should be attributed to the unique hierarchical structure and high fraction of surface active sites of cathode catalyst.
Mesoporous Nico2o4 Nanoflakes As Electrocatalysts for Rechargeable Li-O-2 Batteries

Lixue Zhang,Shengliang Zhang,Kejun Zhang,Gaojie Xu,Xiang He,Shanmu Dong,Zhihong Liu,Changshui Huang,Lin Gu,Guanglei Cui

DOI: https://doi.org/10.1039/c3cc40393a

IF: 4.9

2013-01-01

Chemical Communications

Abstract:Herein, we report the facile synthesis of mesoporous NiCo2O4 nanoflakes and their application in nonaqueous Li-O-2 batteries as cathode catalysts. The assembled Li-O-2 batteries presented lower over-potentials and enhanced cyclability, which should be attributed to the superior electrocatalytic activity and the mesoporous nanostructure of NiCo2O4.
Metal–Organic Framework-Derived Porous NiCo-Layered Double Hydroxide@MnO 2 Hierarchical Nanostructures as Catalytic Cathodes for Long-Life Li–O 2 Batteries

Mingjie Ding,Peng Wang,Zhiwei Zhang,Longwei Yin

DOI: https://doi.org/10.1021/acsaem.0c01626

IF: 6.4

2020-12-31

ACS Applied Energy Materials

Abstract:The commercial application of lithium–oxygen (Li–O2) batteries has been seriously hindered by their large overpotential and inferior cycling performance caused by the insoluble and insulated traits of the discharge product, Li2O2. Herein, hierarchical hollow NiCo-LDH/MnO2 hybrid nanostructures derived from metal–organic frameworks (MOFs) are successfully constructed as cathodes for Li–O2 batteries to fundamentally improve the decomposition kinetics of Li2O2. The hollow NiCo-LDH/MnO2 nanostructures assembled by hollow NiCo-LDH and MnO2 nanosheets possess a highly special surface area, abundant open active sites, and a fast diffusion path for Li+ and oxygen species. As expected, accelerated sluggish oxygen reduction reaction/oxygen evolution reaction kinetics and reduced charge/discharge overpotentials can be obtained. The toroidal Li2O2 assembled by nanoflakes formed on the surface of the cathode can be conducive to form a low-impedance Li2O2/cathode contact interface to achieve the reversible formation and decomposition of Li2O2. The Li–O2 battery based on the NiCo-LDH/MnO2 cathode shows a high charge/discharge specific capacity of 13,380 mA h g–1 at 100 mA g–1 and a continuous cycling stability for 162 cycles at a fixed capacity of 500 mAh g–1 as well as a low overpotential of 0.63 V. Moreover, the application of MOF-derived porous hierarchical nanostructures expands the selection range of electrocatalysts and offers a new idea of structure design for Li–O2 batteries.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsaem.0c01626?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsaem.0c01626</a>.Experimental details, SEM images, TEM images, N2 adsorption/desorption isotherms, EDS image, survey spectrum and electrochemical analysis (discharge/charge curves, Nyquist plots, rate performance, and cycling stability performance), contents of MnO2 in the NiCo 2-X sample calculated from XPS, comparison of the performance of the NiCo 2-X nanocomposite electrodes, and SEM images and XPS spectra of electrodes after discharge and charge (<a class="ext-link" href="/doi/suppl/10.1021/acsaem.0c01626/suppl_file/ae0c01626_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

materials science, multidisciplinary,chemistry, physical,energy & fuels
Spinel LiMn 2 O 4 nanoparticles dispersed on nitrogen-doped reduced graphene oxide nanosheets as an efficient electrocatalyst for aluminium-air battery

jie li,wenzhang li,yaomin li,qiyuan chen,yang liu

DOI: https://doi.org/10.1016/j.ijhydene.2015.05.153

IF: 7.2

2015-01-01

International Journal of Hydrogen Energy

Abstract:Nitrogen-doped reduced graphene oxide nanosheets modified with LiMn2O4 (LMO) nanoparticles as low cost, nontoxic and efficient catalyst for oxygen reduction reaction (ORR) were synthesized by a simple two step hydrothermal method. The physical properties and the activity of the composites toward ORR were investigated using X-ray diffraction (XRD) spectroscopy, transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), energy dispersive X-ray (EDX) spectra, and electrochemical measurements, including cyclic voltammograms (CV), steady state polarization curves and electrochemical impedance spectroscopy (EIS) in O2-saturated 0.1 M KOH electrolyte. The LiMn2O4 supported on nitrogen-doped reduced graphene oxide (LMO/N-rGO) showed more positive onset potential, half wave potential, faster charge transfer, and a higher cathodic peak current in alkaline media than that of LiMn2O4/rGO and N-rGO. Furthermore, air electrodes with hybrid catalysts were fabricated to test the discharged performance in Al-air batteries under ambient air condition. The batteries with LMO/N-rGO cathode displayed the higher energy density of 585 mAh g−1 and sluggish potential drop. The improved catalytic activity and battery performance of LMO/N-rGO can be attributed to the effect of active sites induced by nitrogen, and synergic covalent coupling between the nitrogen-doped graphene sheets and spinel lithium manganese oxide. These results confirm that LMO/N-rGO is a promising material for air cathodes with good activity and stability in aluminium-air battery.
Ultrathin Porous NiCo2O4 Nanosheets for Lithium–Oxygen Batteries: an Excellent Performance Deriving from an Enhanced Solution Mechanism

Xin Guo,Jinqiang Zhang,Yufei Zhao,Bing Sun,Hao Liu,Guoxiu Wang

DOI: https://doi.org/10.1021/acsaem.9b00450

IF: 6.4

2019-01-01

ACS Applied Energy Materials

Abstract:Lithium–oxygen batteries are of interest for long-range electric vehicles owing to their high theoretical energy density. However, the poor cycling performance and low round-trip efficiency deriving from the sluggish oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) kinetics severely impede their practical application. Ingenious design of cathode catalysts is imperative to overcome these challenges. Here, we report ultrathin porous NiCo2O4 nanosheets with abundant oxygen vaccines as an efficient cathode catalyst toward both OER and ORR for Li–O2 batteries. From combined theoretical calculation with experimental results, a unique enhanced solution mechanism is proposed in the ether-based electrolyte system. Benefiting from the porous 2D architecture of the cathode and the hierarchical toroidal products, the Li–O2 batteries using NiCo2O4 cathodes deliver a high discharge capacity of 16 400 mAh g–1 at 200 mA g–1 and an excellent cycling performance up to 150 cycles with a restricted capacit...
Cation-Substitution-Tuned Oxygen Electrocatalyst of Spinel Cobaltite MCo2O4 (M = Fe, Co, and Ni) Hexagonal Nanoplates for Rechargeable Zn-Air Batteries

Peng Tan,Zhen Wu,Bin Chen,Haoran Xu,Weizi Cai,Shaowei Jin,Zongping Shao,Meng Ni

DOI: https://doi.org/10.1149/2.1311914jes

IF: 3.9

2019-01-01

Journal of The Electrochemical Society

Abstract:The spinel cobalt oxide (Co3O4) nanoplate exposed with hexagonal {111} facets is demonstrated to be a highly active catalyst, while the effect of cation substitution on the oxygen electrocatalysis is still unclear. Herein, the electrocatalytic activity of cation-substituted spinel cobaltite MCo2O4 (M = Fe, Co, and Ni) nanoplates with the {111} facets is investigated systematically by experiments and theoretical calculations. For both oxygen reduction and evolution reactions, Ni-substituted Co3O4 hexagonal nanoplates show the best activity. It is mainly attributed to the increased surface energy per unit area and the enhanced oxygen species absorption ability, which are also evidenced by density functional theory calculations. Moreover, the three kinds of MCo2O4 nanoplates are applied in Zn-air batteries and the corresponding electrochemical performance is tested. Among the three batteries, NiCo2O4 hexagonal nanoplates also enable the highest peak power density of 110.3 mW cm(-2) and the most stable discharge-charge voltage profiles for 50 cycles, indicating that NiCo2O4 nanoplates are the promising catalyst for further Zn-air battery applications. Besides, this work illustrates that the substitution of Co by Ni or Fe can remarkably change the electronic structural states, thus tuning the electrochemical properties of the hexagonal Co3O4 nanoplates. (C) 2019 The Electrochemical Society.
Lithium Manganese Spinel Cathodes for Lithium‐Ion Batteries

Yimeng Huang,Yanhao Dong,Sa Li,Jinhyuk Lee,Chao Wang,Zhi Zhu,Weijiang Xue,Yao Li,Ju Li

DOI: https://doi.org/10.1002/aenm.202000997

IF: 27.8

2020-06-23

Advanced Energy Materials

Abstract:Spinel LiMn2O4, whose electrochemical activity was first reported by Prof. John B. Goodenough's group at Oxford in 1983, is an important cathode material for lithium‐ion batteries that has attracted continuous academic and industrial interest. It is cheap and environmentally friendly, and has excellent rate performance with 3D Li+ diffusion channels. However, it suffers from severe degradation, especially under extreme voltages and during high‐temperature operation. Here, the current understanding and future trends of the spinel cathode and its derivatives with cubic lattice symmetry (LiNi0.5Mn1.5O4 that shows high‐voltage stability, and Li‐rich spinels that show reversible hybrid anion‐ and cation‐redox activities) are discussed. Special attention is given to the degradation mechanisms and further development of spinel cathodes, as well as concepts of utilizing the cubic spinel structure to stabilize high‐capacity layered cathodes and as robust framework for high‐rate electrodes. "Good spinel" surface phases like LiNi0.5Mn1.5O4 are distinguished from "bad spinel" surface phases like Mn3O4.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,energy & fuels
Enhancing The Electrochemical Performance Of The Limn2o4 Hollow Microsphere Cathode With A Lini0.5mn1.5o4 Coated Layer

Wei Liu,Jun Liu,Kunfeng Chen,Shaomin Ji,Yanling Wan,Yichun Zhou,Dongfeng Xue,Peter Hodgson,Yuncang Li

DOI: https://doi.org/10.1002/chem.201303675

2014-01-01

Chemistry - A European Journal

Abstract:Spinel cathode materials consisting of LiMn2O4@LiNi0.5Mn1.5O4 hollow microspheres have been synthesized by a facile solution-phase coating and subsequent solid-phase lithiation route in an atmosphere of air. When used as the cathode of lithium-ion batteries, the double-shell LiMn2O4@LiNi0.5Mn1.5O4 hollow microspheres thus obtained show a high specific capacity of 120mAhg(-1) at 1C rate, and excellent rate capability (90mAhg(-1) at 10C) over the range of 3.5-5V versus Li/Li+ with a retention of 95% over 500cycles.
A Novel NiCoMnO4 Anode Material: Construction of Nanosheet Architecture and Superior Electrochemical Performances

Mengjiao Liu,Li Wang,Yanlin Mu,Jianmin Ma,Yan Zhao,Yi Wang,Xin Lai,Jian Bi,Daojiang Gao

DOI: https://doi.org/10.1016/j.scriptamat.2017.10.030

IF: 6.302

2018-01-01

Scripta Materialia

Abstract:Novel NiCoMnO4 nanosheets have been designed and fabricated via a facile hydrothermal derived process. The microstructure results reveal that the as-prepared material has a typical spinel structure and possesses a nanosheet morphology. Due to the unique chemical composition and nanostructure, the NiCoMnO4 nanosheets exhibit a very high reversible capacity of 1329.3mAhg−1 at 200mAg−1 after 100cycles and show excellent rate performance of 501.6mAhg−1 even at 5000mAg−1 when used as anode material for lithium-ion batteries (LIBs).
Porous Cobalt-Manganese Oxide Nanocubes Derived from Metal Organic Frameworks As A Cathode Catalyst for Rechargeable Li-O-2 Batteries

Jian Zhang,Liangjun Wang,Leilei Xu,Xiaoming Ge,Xiao Zhao,Min Lai,Zhaolin Liu,Wei Chen

DOI: https://doi.org/10.1039/c4nr05865h

IF: 6.7

2015-01-01

Nanoscale

Abstract:The development of cathode catalysts with a porous structure is essential to design Li-O-2 batteries with a high rate performance and good cycle stability. Herein, spinel-type porous cobalt-manganese oxide (Co-Mn-O) nanocubes derived from metal organic frameworks were employed as an electrocatalyst in a Li-O-2 battery. The battery with the porous Co-Mn-O nanocubes electrode showed a low overpotential and enhanced capacity. The synergistic effects of large specific surface area, porous structure, and the high electrocatalytic activity of the porous Co-Mn-O nanocubes electrode endowed the Li-O-2 battery with a good rate performance and excellent cycle stability up to 100 cycles.
A gradient oxy-thiophosphate-coated Ni-rich layered oxide cathode for stable all-solid-state Li-ion batteries

Jianwen Liang,Yuanmin Zhu,Xiaona Li,Jing Luo,Sixu Deng,Yang Zhao,Yipeng Sun,Duojie Wu,Yongfeng Hu,Weihan Li,Tsun-Kong Sham,Ruying Li,Meng Gu,Xueliang Sun

DOI: https://doi.org/10.1038/s41467-022-35667-7

IF: 16.6

2023-01-10

Nature Communications

Abstract:Abstract High-energy Ni-rich layered oxide cathode materials such as LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) suffer from detrimental side reactions and interfacial structural instability when coupled with sulfide solid-state electrolytes in all-solid-state lithium-based batteries. To circumvent this issue, here we propose a gradient coating of the NMC811 particles with lithium oxy-thiophosphate (Li 3 P 1+x O 4 S 4x ). Via atomic layer deposition of Li 3 PO 4 and subsequent in situ formation of a gradient Li 3 P 1+x O 4 S 4x coating, a precise and conformal covering for NMC811 particles is obtained. The tailored surface structure and chemistry of NMC811 hinder the structural degradation associated with the layered-to-spinel transformation in the grain boundaries and effectively stabilize the cathode|solid electrolyte interface during cycling. Indeed, when tested in combination with an indium metal negative electrode and a Li 10 GeP 2 S 12 solid electrolyte, the gradient oxy-thiophosphate-coated NCM811-based positive electrode enables the delivery of a specific discharge capacity of 128 mAh/g after almost 250 cycles at 0.178 mA/cm 2 and 25 °C.

multidisciplinary sciences
Preparation of NiO/multiwalled Carbon Nanotube Nanocomposite for Use As the Oxygen Cathode Catalyst in Rechargeable Li–O 2 Batteries

Guangyu Zhao,Li Zhang,Tong Pan,Kening Sun

DOI: https://doi.org/10.1007/s10008-013-2045-z

IF: 2.747

2013-01-01

Journal of Solid State Electrochemistry

Abstract:NiO/multiwalled carbon nanotube (NiO/MWCNT) nanocomposites have been prepared and used for a Li–O2 battery cathode catalyst. Electrochemical measurements demonstrate that the batteries with NiO/MWCNT catalyst have a discharge capacity of 2,500 mAh g−1, a charge capacity of 2,100 mAh g−1, and a rechargeable ability performing better than Ketjenblack (KB) and MWCNTs. KB has the largest discharge capacity (2,700 mAh g−1) due to the highest surface area and pore volume but the worst charging behavior due to poor mass transport in the small-width pore (2.48 nm). MWCNTs have a much better charging performance owing to a larger pore width (8.93 nm) than carbon black. NiO/MWCNTs have the largest charge capacity because of the facilitated mass transport in the comparatively large pores (7.68 nm) and the increased catalytic ability produced by the NiO nanoparticles. These improvements are also responsible for the best cycle and rate performances of the nanocomposites among the three catalysts.

NiMn<sub>2</sub>O<sub>4</sub> as an efficient cathode catalyst for rechargeable lithium–air batteries

Nimn2o4 As An Efficient Cathode Catalyst For Rechargeable Lithium-Air Batteries

Radially Oriented Single‐Crystal Primary Nanosheets Enable Ultrahigh Rate and Cycling Properties of LiNi0.8Co0.1Mn0.1O2 Cathode Material for Lithium‐Ion Batteries

Spinel NiCo2S4 As Excellent Bi-Functional Cathode Catalysts for Rechargeable Li-O-2 Batteries

Spinel LiNixMn2-xO4 as cathode material for aqueous rechargeable lithium batteries

Facile synthesis of spinel CuCo2O4 nanocrystals as high-performance cathode catalysts for rechargeable Li-air batteries.

Ternary Spinel MCo2O4 (M = Mn, Fe, Ni, and Zn) Porous Nanorods as Bifunctional Cathode Materials for Lithium-O2 Batteries

Electrochemical Performance Ni Doped Spinel LiMn2O4 Cathode for Lithium Ion Batteries

Efficient and Durable Bifunctional Oxygen Catalysts Based on NiFeO@MnOx Core-Shell Structures for Rechargeable Zn-Air Batteries

Molybdenum Nitride/N-Doped Carbon Nanospheres for Lithium-O-2 Battery Cathode Electrocatalyst

Mesoporous Nico2o4 Nanoflakes As Electrocatalysts for Rechargeable Li-O-2 Batteries

Metal–Organic Framework-Derived Porous NiCo-Layered Double Hydroxide@MnO 2 Hierarchical Nanostructures as Catalytic Cathodes for Long-Life Li–O 2 Batteries

Spinel LiMn 2 O 4 nanoparticles dispersed on nitrogen-doped reduced graphene oxide nanosheets as an efficient electrocatalyst for aluminium-air battery

Ultrathin Porous NiCo2O4 Nanosheets for Lithium–Oxygen Batteries: an Excellent Performance Deriving from an Enhanced Solution Mechanism

Cation-Substitution-Tuned Oxygen Electrocatalyst of Spinel Cobaltite MCo2O4 (M = Fe, Co, and Ni) Hexagonal Nanoplates for Rechargeable Zn-Air Batteries

Lithium Manganese Spinel Cathodes for Lithium‐Ion Batteries

Enhancing The Electrochemical Performance Of The Limn2o4 Hollow Microsphere Cathode With A Lini0.5mn1.5o4 Coated Layer

A Novel NiCoMnO4 Anode Material: Construction of Nanosheet Architecture and Superior Electrochemical Performances

Porous Cobalt-Manganese Oxide Nanocubes Derived from Metal Organic Frameworks As A Cathode Catalyst for Rechargeable Li-O-2 Batteries

A gradient oxy-thiophosphate-coated Ni-rich layered oxide cathode for stable all-solid-state Li-ion batteries

Preparation of NiO/multiwalled Carbon Nanotube Nanocomposite for Use As the Oxygen Cathode Catalyst in Rechargeable Li–O 2 Batteries