Improvement of Photocatalytic Oxidation Activity on a WO3/TiO2 Heterojunction Composite Photocatalyst with Broad Spectral Response

Baojun Ma,Jinsu Kim,Ting Wang,Jie Li,Kuen‐Song Lin,Wanyi Liu,Seong-Ihl Woo

DOI: https://doi.org/10.1039/c5ra15378f

IF: 4.036

2015-01-01

RSC Advances

Abstract:WO3/TiO2 that can efficiently use ultraviolet and visible light simultaneously was designed and investigated for photocatalytic O2 evolution.

What problem does this paper attempt to address?

Preparation of WOx-TiO2 and the Photocatalytic Activity under Visible Irradiation

Hai Yan Song,Hong Fu Jiang,Xing Qin Liu,Yin Zhu Jiang,Guang Yao Meng

DOI: https://doi.org/10.4028/www.scientific.net/KEM.336-338.1979

2007-01-01

Key Engineering Materials

Abstract:Nanocrystalline tungsten oxide doped titanium dioxide (WOx-TiO2) powders were prepared by TiCl4 hydrolysis and characterized by XRD, XPS, UV-Vis absorption spectra and TEM. Results showed that WO, not only hindered the growth of TiO2 particles but also greatly increased the transformation temperature (>800 degrees C) from anatase to rutile during sintering; the dominant fraction of tungsten oxides was non-stoichiometric tungsten oxide (WxOy) with Wn+ (4<n<6), which could easily substitute Ti4+ in the lattice of TiO2. The light absorption band of TiO2 changed from the near UV to the visible light range (2.68 eV in 1.0 %WOx-TiO2) because of the tungsten impurity energy level induced by WxTi1-xO2. The photocatalysis experiments demonstrated that the MB in aqueous solution was successfully degraded within 1h using WOx-TiO2 with an optimal WOx dosage of 1% under visible light irradiation.
Fabrication and photocatalytic performance of WO3/TiO2 heterojunction composites

Qianru Zhao,Shuangyang Chen,Binghua Ren,Sinan Liu,Yongchao Zhang,Xi Luo,Wei Feng,Yan Sun

DOI: https://doi.org/10.1016/j.optmat.2022.113266

IF: 3.754

2023-01-01

Optical Materials

Abstract:The rutile TiO2 microspheres and WO3 nanosheets were both synthesized via the hydrothermal treatment and the type-II WO3/TiO2 heterojunction with different mass ratios (1:2, 1:5, and 1:8) was prepared by a simple physical mixing method. The photocatalytic performance of the photocatalysts was investigated by the degradation of Rhodamine B (RhB) dye under simulated sunlight irradiation. Compare with pure TiO2 and WO3, the WO3/TiO2 with a mass ratio of 1:5 exhibited the highest photocatalytic efficiency of 91.5% within 60 min. The active species trapping experiment revealed that holes (h+) and superoxide radical (·O2 −) played main roles in the degradation process. The unique type-II WO3/TiO2 heterojunction not only extended the light absorption range, but also promoted charge carriers transfer and separation, leading to the enhancement of photocatalytic activity.

materials science, multidisciplinary,optics
Application of tungsten oxide and its composites in photocatalysis

Xinyue Gu,Shu Lin,Kezhen Qi,Ya Yan,Ruchun Li,Vadim Popkov,Oksana Almjasheva

DOI: https://doi.org/10.1016/j.seppur.2024.127299

IF: 8.6

2024-04-08

Separation and Purification Technology

Abstract:WO 3 -based photocatalysis has garnered significant interest among researchers worldwide. With a band gap ranging between 2.5 and 2.7 eV, WO 3 emerges as a promising candidate material for photocatalytic applications due to its excellent electrochemical properties, high stability, and ability to enhance photoactivity in various crystalline forms. Noteworthy features of WO 3 include exceptional stability in harsh conditions, cost-effectiveness, high hole drift velocity, and a tunable energy gap. In this comprehensive review, we first explore the diverse morphologies of WO 3 obtained through different preparation methods. Secondly, we investigate the photocatalytic efficiency of WO 3 -based composites. Thirdly, strategies for identifying optimal photocatalysts, such as crystal plane optimization, doping, surface modification, coupling carbon materials, and hetero/homojunction fabrication, are summarized. Additionally, the integration of WO 3 -based composites to form type-II, Z-scheme, and S-scheme configurations is detailed. The review delves into various applications of WO 3 , including pollutant degradation, CO 2 reduction, and water splitting, providing an in-depth analysis. Furthermore, the challenges and prospects associated with WO 3 -based photocatalysts are highlighted, along with discussions on methods to enhance their performance. This review aims to inspire academics to innovate concepts for advancing sustainable energy production in the next generation.

engineering, chemical
Highly efficient water purification by WO3-based homo/heterojunction photocatalyst under visible light

Kunihiko Kato,Takashi Shirai

DOI: https://doi.org/10.1016/j.jallcom.2021.163434

IF: 6.2

2022-04-01

Journal of Alloys and Compounds

Abstract:Bandgap engineering has attracted increasing interest in the field of semiconductive materials with specific electrical and optical characteristics for various applications, such as solar energy harvesting, energy-related applications, and photocatalysts. Here, we propose a novel and facile method to obtain a combination of type-II structure and Ohmic contact by the fabrication of WO3/Ti-WOx/TiHyOz homo/heterojunction on a WO3 photocatalyst using ball milling. The morphology and structural characterizations of the material are obtained using UV–vis, SEM/EDS, XRD, Raman spectroscopy, and XPS. It is revealed that titanium hydride (TiH2) facilitates simultaneous WO3 reduction and cation doping, which generates intervalent W ions (W5+, W4+) with oxygen deficiency, leading to the formation of new band structures at the WO3/Ti-WOx/TiHyOz interface. As a result, the homo/heterojunction significantly extends light absorption above 400 nm and facilitates the spatial separation of photoexcited carriers, which significantly enhances the photocatalytic performance to degrade azo-dye water pollutants under visible light irradiation.

materials science, multidisciplinary,chemistry, physical,metallurgy & metallurgical engineering
Improved Visible-Light Photocatalytic Degradation of Pollutants under the Synergistic Effect of BiOI/BiFeWO6 P-N Heterojunction and Oxygen Vacancies

Yiming Sun,Cong Lu,Yongli Yin,Haifeng Zhou,Peng Liang

DOI: https://doi.org/10.1016/j.apsusc.2023.157588

IF: 6.7

2023-01-01

Applied Surface Science

Abstract:The construction of p-n heterojunctions has become an effective way to develop high performance photocatalysts to remove pollutants from water. Herein, the BiOI/BiFeWO6 composites abundant in oxygen vacancies (OVs) was rationally designed by combining calcination and solvothermal methods to remove different kinds of pollutants, including rhodamine B (RhB), tetracycline (TC), ciprofloxacin (CIP) and hexavalent chromium (Cr(VI)). The surface properties, structural characterizations and photocatalytic activity of BiOI/BiFeWO6 were investigated. Scanning electron microscope (SEM) and transmission electron microscope (TEM) showed that the morphology of BiOI/BiFeWO6 was BiFeWO6 nanoparticles loaded on BiOI sheet structure. The formation of BiOI/BiFeWO6 heterojunction was demonstrated by the shift of the peaks of Bi and I elements in X-ray photoelectron spec-troscopy (XPS). Moreover, the existence of OVs was confirmed by the O 1 s spectrum and electron spin resonance (ESR). By comparison with neat BiOI and BiFeWO6, the BiOI/BiFeWO6 composite showed excellent photo -catalytic properties under visible light. The strategy that the p-n heterojunction and OVs work together opens up new avenues to fabricate future high-efficiency photocatalysts.
Research Progress of Tungsten Oxide-Based Catalysts in Photocatalytic Reactions

Zenan Ni,Qiuwen Wang,Yuxin Guo,Huimin Liu,Qijian Zhang

DOI: https://doi.org/10.3390/catal13030579

IF: 3.9

2023-03-14

Catalysts

Abstract:Photocatalysis technology is a potential solution to solve the problem of environmental pollution and energy shortage, but its wide application is limited by the low efficiency of solar energy conversion. As a non-toxic and inexpensive n-type semiconductor, WO3 can absorb approximately 12% of sunlight which is considered one of the most attractive photocatalytic candidates. However, the narrow light absorption range and the high recombination rate of photogenerated electrons and holes restrict the further development of WO3-based catalysts. Herein, the studies on preparation and modification methods such as doping element, regulating defects and constructing heterojunctions to enlarge the range of excitation light to the visible region and slow down the recombination of carriers on WO3-based catalysts so as to improve their photocatalytic performance are reviewed. The mechanism and application of WO3-based catalysts in the dissociation of water, the degradation of organic pollutants, as well as the hydrogen reduction of N2 and CO2 are emphatically investigated and discussed. It is clear that WO3-based catalysts will play a positive role in the field of future photocatalysis. This paper could also provide guidance for the rational design of other metallic oxide (MOx) catalysts for the increasing conversion efficiency of solar energy.

chemistry, physical
WO3-based photocatalysts: morphology control, activity enhancement and multifunctional applications

Pengyu Dong,Guihua Hou,Xinguo Xi,Rong Shao,Fan Dong

DOI: https://doi.org/10.1039/c6en00478d

2017-01-01

Abstract:WO3, a visible-light responsive photocatalyst, absorbs light up to 480 nm with several intriguing advantages such as low cost, harmlessness, and stability in acidic and oxidative conditions. In this review, the relationship between the morphology control and the photocatalytic activity of WO3 is analyzed in detail. In particular, the WO3 exposed {002}-dominant facet with high-surface-energy generally shows excellent photocatalytic performance, and the quantum-confined WO3 nanoparticles exhibit a promising future. Furthermore, some main strategies for improving the photocatalytic activity of WO3, such as surface hybridization with graphene, noble metal deposition, semiconductor coupling, and alkali hydroxide loading, are systematically summarized and highlighted. In the noble metal/WO3 composite, the noble metal always works as an electron pool and catalyzes O-2 reduction through a multi-electron reduction process to form H2O2 and H2O instead of the traditional single-electron process. In addition, the preparation methods, photocatalytic enhancement factors and possible photocatalytic mechanisms for the WO3/semiconductor composites are described. Moreover, various photocatalytic applications of WO3-based photocatalysts, such as photodegradation of organics, air purification, self-cleaning, CO2 photoreduction, heavy metal ion treatment, hydrogen evolution from splitting water, and bacterial disinfection, are introduced and summarized. Finally, the main conclusions and future perspectives of WO3-based photocatalysts are pointed out. It is anticipated that this review could offer guidelines for designing novel WO3-based photocatalysts with low cost and high efficiency, which can possess promising prospects of application to meet the urgent demands of highly efficient solar energy conversion in the areas of renewable energy and environmental purification.
Cs-Doped WO3 with Enhanced Conduction Band for Efficient Photocatalytic Oxygen Evolution Reaction Driven by Long-Wavelength Visible Light

Dong Li,Siyu Tian,Qiuhua Qian,Caiyun Gao,Hongfang Shen,Fei Han

DOI: https://doi.org/10.3390/molecules29133126

IF: 4.6

2024-06-30

Molecules

Abstract:Cesium doped WO3 (Cs-WO3) photocatalyst with high and stable oxidation activity was successfully synthesized by a one-step hydrothermal method using Cs2CO3 as the doped metal ion source and tungstic acid (H2WO4) as the tungsten source. A series of analytical characterization tools and oxygen precipitation activity tests were used to compare the effects of different additions of Cs2CO3 on the crystal structure and microscopic morphologies. The UV-visible diffuse reflectance spectra (DRS) of Cs-doped material exhibited a significant red shift in the absorption edge with new shoulders appearing at 440-520 nm. The formation of an oxygen vacancy was confirmed in Cs-WO3 by the EPR signal, which can effectively regulate the electronic structure of the catalyst surface and contribute to improving the activity of the oxygen evolution reaction (OER). The photocatalytic OER results showed that the Cs-WO3-0.1 exhibited the optimal oxygen precipitation activity, reaching 58.28 µmol at 6 h, which was greater than six times higher than that of WO3-0 (9.76 μmol). It can be attributed to the synergistic effect of the increase in the conduction band position of Cs-WO3-0.1 (0.11 V) and oxygen vacancies compared to WO3-0, which accelerate the electron conduction rate and slow down the rapid compounding of photogenerated electrons-holes, improving the water-catalytic oxygen precipitation activity of WO3.
Improved visible-light photocatalytic degradation of pollutants under the synergistic effect of BiOI/BiFeWO 6 p-n heterojunction and oxygen vacancies

Yiming Sun,Cong Lu,Yongli Yin,Haifeng Zhou,Peng Liang

DOI: https://doi.org/10.1016/j.apsusc.2023.157588

IF: 6.7

2023-05-24

Applied Surface Science

Abstract:The construction of p-n heterojunctions has become an effective way to develop high performance photocatalysts to remove pollutants from water. Herein, the BiOI/BiFeWO 6 composites abundant in oxygen vacancies (OVs) was rationally designed by combining calcination and solvothermal methods to remove different kinds of pollutants, including rhodamine B (RhB), tetracycline (TC), ciprofloxacin (CIP) and hexavalent chromium (Cr(VI)). The surface properties, structural characterizations and photocatalytic activity of BiOI/BiFeWO 6 were investigated. Scanning electron microscope (SEM) and transmission electron microscope (TEM) showed that the morphology of BiOI/BiFeWO 6 was BiFeWO 6 nanoparticles loaded on BiOI sheet structure. The formation of BiOI/BiFeWO 6 heterojunction was demonstrated by the shift of the peaks of Bi and I elements in X-ray photoelectron spectroscopy (XPS). Moreover, the existence of OVs was confirmed by the O 1s spectrum and electron spin resonance (ESR). By comparison with neat BiOI and BiFeWO 6 , the BiOI/BiFeWO 6 composite showed excellent photocatalytic properties under visible light. The strategy that the p-n heterojunction and OVs work together opens up new avenues to fabricate future high-efficiency photocatalysts.

chemistry, physical,physics, applied, condensed matter,materials science, coatings & films
Photocatalytic Activity of WOx-TiO2 under Visible Light Irradiation

XZ Li,FB Li,CL Yang,WK Ge

DOI: https://doi.org/10.1016/s1010-6030(01)00446-4

IF: 5.141

2001-01-01

Journal of Photochemistry and Photobiology A Chemistry

Abstract:With an attempt to extend light absorption of the TiO2-based photocatalysts toward the visible light range and eliminate the rapid recombination of excited electrons/holes during photoreaction, new photocatalyst (WOx-TiO2) powder was prepared by a sol–gel method. The photooxidation efficiency of WOx-TiO2 catalyst was also evaluated by conducting a set of experiments to photodegrade methylene blue (MB) in aqueous solution. The photocatalytic activity of WOx-TiO2 was examined by X-ray diffraction (XRD), UV–VIS absorption spectra, X-ray photoelectron emission spectroscopy (XPS), photoluminescence spectra (PL), surface photovoltage spectra (SPS) and electron-field-induced surface photovoltage spectra (EFISPS). The experiments demonstrated that the MB in aqueous solution was successfully photodegraded using WOx-TiO2 under visible light irradiation. It was found that an optimal WOx dosage of 3% in WOx-TiO2 achieved the highest rate of MB photodegradation in this experimental condition. It has been confirmed that WOx-TiO2 could be excited by visible light (E<3.2eV) and the recombination rate of electrons/holes in WOx-TiO2 declined due to the existence of WO3 doped in TiO2. The order of its photoactivity from weak to strong had a good agreement with that of PL intensity and that of EFISPS intensity from strong to weak.
Synthesis, characterization and photocatalytic activity of porous WO 3 /TiO 2 hollow microspheres

liuyang yang,zhichun si,duan weng,youwei yao

DOI: https://doi.org/10.1016/j.apsusc.2014.05.230

IF: 6.7

2014-01-01

Applied Surface Science

Abstract:Porous WO3/TiO2 hollow microspheres were prepared by a spray drying method for photodegradation of methylene blue and phenol. The catalysts were characterized by X-ray diffraction, Field Emission Scanning Electron Microscope, High Resolution Transmission Electron Microscope, N2 adsorption–desorption measurements, Raman spectrometer, UV–Vis Diffuse Reflectance Spectroscopy and Zeta-Meter measurements. The results showed that the tungsten oxides mainly existed in highly dispersed amorphous form on anatase when the loading amount of tungsten oxide was below 3mol%. The improved photocatalytic activity under UV light irradiation of the WO3/TiO2 catalyst mainly arises from the enhanced charge separation efficiency rather than the improved light absorbance by highly dispersed amorphous tungsten oxides. Highly dispersed amorphous WOx can form a shallowly trapped site due to its similar band structure with TiO2. The strongly electron-withdrawing of tungsten oxide in highly dispersed state facilitates the electron transition between titanium and WOx, and consequently improves the charge separation. The enhanced acidity of catalyst by WOx in reactant environment also improved the charge separation efficiency due to the timely transition of holes and electrons accumulated on TiO2 and WOx, respectively. However, the improved photocatalytic activity under visible light irradiation of the WO3/TiO2 catalyst mainly arises from light harvest. TiO2 containing 3 mol% WO3 displayed the highest photocatalytic activity under UV light irradiation while that containing 4 mol% WO3 present highest activity under visible light irradiation.
A photochromic composite with enhanced carrier separation for the photocatalytic activation of benzylic C–H bonds in toluene

Xing Cao,Zheng Chen,Rui Lin,Weng-Chon Cheong,Shoujie Liu,Jian Zhang,Qing Peng,Chen Chen,Tong Han,Xuanjue Tong,Yu Wang,Rongan Shen,Wei Zhu,Dingsheng Wang,Yadong Li

DOI: https://doi.org/10.1038/s41929-018-0128-z

IF: 37.8

2018-09-01

Nature Catalysis

Abstract:Photocatalysis based on the use of semiconducting materials is an emerging alternative to conventional thermochemical catalysis, and it has the potential to promote chemical synthesis under greener and milder conditions. However, heterogeneous photocatalytic organic reactions are still in their infancy, limited by the low-efficiency carrier separation of the currently available photocatalytic materials. Here, we report photochromic Bi2WO6–x/amorphous BiOCl (p-BWO) nanosheets, which, distinct from pristine Bi2WO6, show blue colouration upon visible light irradiation and are bleached by atmospheric oxygen. Studies on the microscopic structure of the material reveal the existence of abundant W(vi)O6–x units, which serve as the sites for the fast and continuous consumption of photogenerated electrons, thereby effectively facilitating the separation of electron–hole pairs. The prepared composite features a remarkable enhancement in performance for the photocatalytic oxidation of toluene with a conversion rate 166-fold higher compared with that of pristine Bi2WO6.

chemistry, physical
Improved Visible Light Photocatalytic Activity of WO3 Through CuWO4 for Phenol Degradation

Haihang Chen,Xianqiang Xiong,Linlin Hao,Xiao Zhang,Yiming Xu

DOI: https://doi.org/10.1016/j.apsusc.2016.07.145

IF: 6.7

2016-01-01

Applied Surface Science

Abstract:Development of a visible light photocatalyst is challenging. Herein, we report a significant activity enhancement of WO3 upon addition of CuWO4. Reaction was carried out under visible light for phenol degradation in aqueous suspension in the presence of H2O2. A maximum reaction rate was observed at 1.0 wt% CuWO4, which was 2.1 and 4.3 times those measured with WO3 and CuWO4, respectively. Similar results were also obtained from the photocatalytic formation of OH radicals, and from the electrochemical reduction of O-2. A possible mechanism responsible for the improved activity of WO3 is proposed, involving the electron transfer from CuWO4 to WO3, followed by the reduction of H2O2 over WO3. (C) 2016 Elsevier B.V. All rights reserved.
Enhanced photocatalytic performance of tungsten-based photocatalysts for degradation of volatile organic compounds: a review

Qiang Cheng,Gao-Ke Zhang

DOI: https://doi.org/10.1007/s42864-020-00055-5

2020-09-01

Tungsten

Abstract:Photocatalytic oxidation process for the degradation of volatile organic compounds (VOCs) contaminants is a promising technology. But until now, the low photocatalytic activity of the conventional TiO2 photocatalyst under visible-light irradiation hinders the deployment of this technique for VOCs degradation. WO3 has been proved to be a suitable photocatalytic material for degradation of various VOCs as its appropriate band-gap, high stability and great capability. Nevertheless, the actual implementation of WO3 is still restricted by short lifetime of photoexcited charge carriers and low light energy conversion efficiency: its photocatalytic performance is needed to be improved. This review discusses the process of tungsten-based photocatalyst for removal of VOCs and summarizes a variety of strategies to improve the VOCs oxidation performances of WO3, such as controlling the morphology structure, engendering chemical defects, coupling heterojunction, doping suitable dopants and loading a co-catalyst. In addition, the practical application of tungsten-based photocatalyst is discussed.

English Else
Enhanced photocatalytic ammonia oxidation over WO3@TiO2 heterostructures by constructing an interfacial electric field

Zhaonian Li,Daorong Li,Zhanzhao Feng,Shuqi Lv,Qingxuan Zhang,Yanru Yu,Ying Tian,Runfeng Huang,Hongxia Chen,Kunfeng Zhang,Hongxing Dai

DOI: https://doi.org/10.1016/j.chemosphere.2024.141811

IF: 8.8

Chemosphere

Abstract:WO3 nanorods and xWO3@TiO2 (WO3/TiO2 mass ratio (x) = 1-5) photocatalysts were synthesized using the hydrothermal and sol-gel methods, respectively. The photocatalytic activities of xWO3@TiO2 for NH3 oxidation first increased and then decreased with a rise in TiO2 content. Among them, the heterostructured 3WO3@TiO2 photocatalyst showed the highest NH3 conversion (58 %) under the simulated sunlight irradiation, which was about two times higher than those of WO3 and TiO2. Furthermore, the smallest amounts of by-products (i.e., NO and NO2) were produced over 3WO3@TiO2. The enhancement in photocatalytic performance (i.e., NH3 conversion and N2 selectivity) of 3WO3@TiO2 was mainly attributed to the formed interfacial electric field between WO3 and TiO2, which promoted efficient separation and transfer of photogenerated charge carriers. Based on the results of reactive species trapping and active radical detection, photocatalytic oxidation of NH3 over 3WO3@TiO2 was governed by the photogenerated holes and superoxide radicals. This work combines two strategies of morphological regulation and interfacial electric field construction to simultaneously improve light utilization and photogenerated charge separation efficiency, which promotes the development of full-spectrum photocatalysts for the removal of ammonia.
Construction of photocatalyst by modification of argentum noble metal and hydrogen doping into WO 3 nanoparticles: Enhancing the solar energy utilization

Jun Li,Na Luo,Yinhai Wang,Han Li,Tao Zhang,Xingui Tang,Zhengfa Hu

DOI: https://doi.org/10.1016/j.fuel.2023.128966

IF: 7.4

2023-06-26

Fuel

Abstract:Solar energy is considered sustainable green energy to prevent environmental pollution. Tungsten trioxide (WO 3 ) is one of the attractive solar energy-driven photocatalysts and photocatalytic supports. Besides, Hydrogen (H) has a small size and can move into many inorganic compounds, and occupy the sites in microstructure as well, with little space structure expansion. H doping in semiconductors attracts more and more attention due to its effect of providing free carriers, resulting in localized surface plasmon resonances which can improve the utilization efficiency of solar energy. In our research, we developed a new method to prepare the H-doped WO 3 whose color turned green, and to prepare Ag/H x WO 3 , which could extend the solar light response range to near-infrared. Furthermore, the photocatalytic activity to degrade RhB solution under UV light and visible light was both improved. The density of free electrons is based on the Drude model to discuss the mechanism of photocatalysis upon the visible. The contact of noble metal Ag and H x WO 3 can play a vital effect in the separation of photogenerated electron-hole pairs. The localized surface plasmon resonances and green coloration bring the tungsten trioxide more remarkable performance together. Results showed that constructed photocatalysis of this work greatly enhanced the utilization rate of solar energy. Photocatalytic for the Degradation of liquid organic pollutants with H x WO 3 is believed to have a bright feature.

energy & fuels,engineering, chemical
Photoelectrochemical H2 evolution on WO3/BiVO4 enabled by single-crystalline TiO2 overlayer modulations

Eunoak Park,Santosh S Patil,Hyeonkwon Lee,Vijay S Kumbhar,Kiyoung Lee

DOI: https://doi.org/10.1039/d1nr04763a

IF: 6.7

2021-10-21

Nanoscale

Abstract:Tungsten oxide/bismuth vanadate (WO3/BiVO4) has emerged as a promising photoanode material for photoelectrochemical (PEC) water splitting owing to its facilitated charge separation state differing significantly from single phase materials. Practical implementation of WO3/BiVO4 is often limited by poor stability arising from the leaching of V5+ from BiVO4 during PEC operations. Herein, we demonstrate that the synthesis of a tungsten oxide/bismuth vanadate/titanium oxide (WO3/BiVO4/TiO2) heterostructure onto a fluorine-doped tin oxide-coated glass substrate through a combined simple hydrothermal-spin coating strategy will advance PEC performance while slowing water oxidation kinetics and improving photostability. We show that surface postmodification with a nanometer-thick layer of (1 0 1) monofacet-selective single-crystalline TiO2 provides stable photocurrent density, up to 1.04 mA cm-2 at 1.23 V (compared to a reversible hydrogen electrode in 0.5 M Na2SO4), with excellent quantum efficiency (45% at 460 nm) and long-term photostability (24 h). Interestingly, crystalline TiO2 activation layers behave differently from previous TiO2 amorphous layers, blocking surface defects while improving corrosion resistance, photostability, and the electron transfer process. These results indicate a ≈2.5 times enhancement in photoelectrocatalytic activity related to referenced WO3/BiVO4 photoanodes, encouraging the use of single-crystalline TiO2 modulations to develop a range of materials for PEC/photocatalytic applications.
WO3·nH2O-based photocatalysts: Structural analysis, rational design, and applications in energy conversion and environmental remediation

Fangyuan Zhang,Weiguang Han,Jinyuan Cai,Boxiong Shen,Sheng-Qi Guo

DOI: https://doi.org/10.1016/j.fuel.2024.131289

IF: 7.4

2024-06-01

Fuel

Abstract:Photocatalysis is an attractive “green” solution to the energy crisis and environmental pollution; however, its practical application is still thwarted by low efficiency. As the core link of this technology, the continuous development of new photocatalysts is the main idea to improve efficiency. In the past few decades, a large number of semiconductor materials with photocatalytic activity have been synthesized successively, including transition metal oxides, nitrides, sulfides, carbon based materials, and metal organic frameworks. Considering various factors such as catalytic activity, production cost, and environmental safety, metal oxides are the most promising carriers of photocatalytic materials for development among them, such as titanium dioxide (TiO2). Recently, tungsten trioxide (WO3) based photocatalyst, especially tungsten trioxide hydrates (WO3·nH2O, n = 0.33, 0.5, 1 and 2), has become a new favorite among scholars. Not only due to its wider light response range and higher photocatalytic activity compared to TiO2, but also because the rich hydroxyl groups give it more flexible surface structure regulation possibilities. At present, there are over 200 literatures on WO3·nH2O-based photocatalysts have published; yet, no review article concluding such materials. To promote the development and provide a reference for colleagues, we present a systematic review of the applications and research progress of WO3·nH2O-based photocatalysts in the past decade. Starting from structural analysis, this work summarizes the preparation methods and modification strategies. Subsequently, it explores the application status in energy conversion and environmental pollution control, and finally a critical assessment and outlook of technical challenges and research opportunities for future was proposed.

energy & fuels,engineering, chemical
Efficient promotion of charge transfer and separation in hydrogenated TiO2/WO3 with rich surface-oxygen-vacancies for photodecomposition of gaseous toluene

Juan-Juan Li,Bo Weng,Song-Cai Cai,Jing Chen,Hong-Peng Jia,Yi-Jun Xu

DOI: https://doi.org/10.1016/j.jhazmat.2017.08.077

IF: 13.6

2018-01-01

Journal of Hazardous Materials

Abstract:Oxygen-deficient TiO2/WO3 constructed via the controllable temperature of hydrogen annealing is designed in view of combining the broad visible spectrum absorption with the prominent coupled semiconductor properties. Surface lattice disorder of TiO2/WO3 arises at hydrogen annealing temperature of 200 and 300°C, while critical phase transition from TiO2/WO3 to TiO2/WO2.9 occurs at 400°C, both of which can introduce oxygen vacancies. The hydrogenated TiO2/WO3 with rich surface-oxygen-vacancies exhibits much higher photocatalytic activity for decomposition of gaseous toluene than pristine TiO2/WO3 under visible-light illumination (λ>420nm). The photoelectrochemical analysis shows that the improved electronic properties of oxygen-deficient TiO2/WO3 enable dramatically efficient promotion of photoinduced charge transfer and separation, which is the key factor for the improved photocatalytic activity. It is hoped that the present work could boost ongoing interest for preparing various hydrogenated coupled semiconductors with enhanced activity for diverse photocatalytic applications.

environmental sciences,engineering, environmental
Microwave–assisted synthesis of nanoscale tungsten trioxide hydrate with excellent photocatalytic activity under visible irradiation

Xu–Teng Yu,Heng–Xin Liu,Yanhua Shen,Jian–Ying Xu,Feng–Ying Cai,Taohai Li,Jian Lü,Wei Cao

DOI: https://doi.org/10.1016/j.inoche.2020.108147

IF: 3.428

2020-10-01

Inorganic Chemistry Communications

Abstract:<h2 class="section-title u-h3 u-margin-l-top u-margin-xs-bottom">Highlights</h2><dl class="list"><dt class="list-label">•</dt><dd class="list-description">WO3•1/3H2O nanoparticles were prepared via a microwave–assisted synthetic pathway.</dd><dt class="list-label">•</dt><dd class="list-description">The WO3•1/3H2O showed enhanced photocatalytic dye degradation capacity.</dd><dt class="list-label">•</dt><dd class="list-description">The WO3•1/3H2O exhibited excellent stability and reusability.</dd><dt class="list-label">•</dt><dd class="list-description">Absterct.</dd><dt class="list-label">•</dt><dd class="list-description">Tungsten trioxide hydrate (WO3•1/3H2O) nanoparticles (NPs) were prepared via a microwave–assisted synthetic pathway by using Na2WO4•2H2O and PdCl2 as precursors. Microstructure and morphology of as–prepared WO3•1/3H2O NPs were investigated through X–ray diffraction patterns (XRD), transmission electron microscopy (TEM), and Fourier transform infrared (FT–IR) spectra, while porosity and bandgap through specific surface area and UV–vis absorption spectroscopy. It was found that Pd2+ ions played a crucial role in the formation of WO3•1/3H2O NPs, and thus a possible formation mechanism was proposed based on the growth processes. The photocatalytic property of WO3•1/3H2O NPs were evaluated on the basis of Rhodamine B (RhB) degradation in aqueous solutions under simulated visible irradiation. The photocatalytic experimental results indicated that as–prepared WO3•1/3H2O NPs exhibited much more superior photocatalytic activity by contrast to that of the commercial WO3.</dd></dl>

chemistry, inorganic & nuclear

Improvement of Photocatalytic Oxidation Activity on a WO3/TiO2 Heterojunction Composite Photocatalyst with Broad Spectral Response

Preparation of WO<sub>x</sub>-TiO<sub>2</sub> and the Photocatalytic Activity under Visible Irradiation

Fabrication and photocatalytic performance of WO3/TiO2 heterojunction composites

Application of tungsten oxide and its composites in photocatalysis

Highly efficient water purification by WO3-based homo/heterojunction photocatalyst under visible light

Improved Visible-Light Photocatalytic Degradation of Pollutants under the Synergistic Effect of BiOI/BiFeWO6 P-N Heterojunction and Oxygen Vacancies

Research Progress of Tungsten Oxide-Based Catalysts in Photocatalytic Reactions

WO3-based photocatalysts: morphology control, activity enhancement and multifunctional applications

Cs-Doped WO3 with Enhanced Conduction Band for Efficient Photocatalytic Oxygen Evolution Reaction Driven by Long-Wavelength Visible Light

Improved visible-light photocatalytic degradation of pollutants under the synergistic effect of BiOI/BiFeWO 6 p-n heterojunction and oxygen vacancies

Photocatalytic Activity of WOx-TiO2 under Visible Light Irradiation

Synthesis, characterization and photocatalytic activity of porous WO 3 /TiO 2 hollow microspheres

A photochromic composite with enhanced carrier separation for the photocatalytic activation of benzylic C–H bonds in toluene

Improved Visible Light Photocatalytic Activity of WO3 Through CuWO4 for Phenol Degradation

Enhanced photocatalytic performance of tungsten-based photocatalysts for degradation of volatile organic compounds: a review

Enhanced photocatalytic ammonia oxidation over WO3@TiO2 heterostructures by constructing an interfacial electric field

Construction of photocatalyst by modification of argentum noble metal and hydrogen doping into WO 3 nanoparticles: Enhancing the solar energy utilization

Photoelectrochemical H2 evolution on WO3/BiVO4 enabled by single-crystalline TiO2 overlayer modulations

WO3·nH2O-based photocatalysts: Structural analysis, rational design, and applications in energy conversion and environmental remediation

Efficient promotion of charge transfer and separation in hydrogenated TiO2/WO3 with rich surface-oxygen-vacancies for photodecomposition of gaseous toluene

Microwave–assisted synthesis of nanoscale tungsten trioxide hydrate with excellent photocatalytic activity under visible irradiation