Abstract:Purpose Since the biomedical implants with an improved compressive strength, near bone elastic modulus, controlled porosity, and sufficient surface roughness, can assist in long term implantation. Therefore, the fine process tuning plays its crucial role to develop optimal settings to achieve these desired properties. This paper aims to find applications for fine process tuning in laser powder bed fusion of biomedical Ti alloys for load-bearing implants. Design/methodology/approach In this work, the parametric porosity simulations were initially performed to simulate the process-induced porosity for selective laser-melted Ti 6 Al 4 V as per full factorial design. Continually, the experiments were performed to validate the simulation results and perform multiresponse optimization to fine-tune the processing parameters. Three levels of each control variable, namely, laser power – Pl (180, 190, 200) W, scanning speed – Vs (1500, 1600, 1700) mm/s and scan orientation – Θ{1(0,0), 2(0,67°), 3(0,90°)} were used to investigate the processing performance. The measured properties from this study include compressive yield strength, elastic modulus, process-induced porosity and surface roughness. Finally, confirmatory experiments and comparisons with the already published works were also performed to validate the research results. Findings The results of porosity parametric simulation and experiments in selective laser melting of Ti 6 Al 4 V were found close to each other with overall porosity (less than 10%). The fine process tuning was resulted in optimal settings [Pl (200 W), Vs (1500 mm/s), Θ (0,90°)], [Pl (200 W), Vs (1500 mm/s), Θ (0,67°)], [Pl (200 W), Vs (1500 mm/s), Θ (0,0)] and [Pl (200 W), Vs (1500 mm/s), Θ (0,0)] with higher compressive strength (672.78 MPa), near cortical bone elastic modulus (12.932 GPa), process-induced porosity (0.751%) and minimum surface roughness (2.72 μm). The morphology of the selective laser melted (SLMed) surface indicated that the lack of fusion pores was prominent because of low laser energy density among the laser and powder bed. Confirmatory experimentation revealed that an overall percent improvement of around 15% was found between predicted and the experimental values. Originality/value Since no significant works are available on the collaborative optimization and fine process tuning in laser powder bed fusion of biomedical Ti alloys for different load bearing implants. Therefore, this work involves the comprehensive investigation and multi-objective optimization to determine optimal parametric settings for better mechanical and physical properties. Another novel aspect is the parametric porosity simulation using Ansys Additive to assist in process parameters and their levels selection. As a result, selective laser melted Ti alloys at optimal settings may help in examining the possibility for manufacturing metallic implants for load-bearing applications.

Evaluation of Treatment Effect and Mechanism Analysis of Ti6AL4V Porous Scaffolds Prepared by Selective Laser Melting with Different Chemical Polishing Processes

Study on the Effect of Dynamic Chemical Polishing Treatment on Porous Titanium Alloy Scaffolds Fabricated Using Laser Powder Bed Fusion

Effect of electropolishing on mechanical property enhancement of Ti6Al4V porous materials fabricated by selective laser melting

Microstructure development of Ti scaffold by laser powder bed fusion with chemical polishing and its mechanical properties, biocompatibility

Optimization of Structural and Processing Parameters for Selective Laser Melting of Porous 316L Bone Scaffolds

Influence of HIP Treatment on Mechanical Properties of Ti6Al4V Scaffolds Prepared by L-PBF Process

Effects of Process Parameters on the Microstructure and Properties of Selective Laser Melting 316L Negative Re-entrant Hexagonal Honeycomb Porous Bone Scaffolds

Influence of the Pore Size and Porosity of Selective Laser Melted Ti6Al4V ELI Porous Scaffold on Cell Proliferation, Osteogenesis and Bone Ingrowth.

Improving osteoinduction and osteogenesis of Ti6Al4V alloy porous scaffold by regulating the pore structure

Chemical etching of Ti‐6Al‐4V biomaterials fabricated by selective laser melting enhances mesenchymal stromal cell mineralization

Post-Processing Treatment Impact on Mechanical Properties of SLM Deposited Ti-6Al-4 V Porous Structure for Biomedical Application

Effect of lattice type on biomechanical and osseointegration properties of 3D-printed porous Ti6Al4V scaffolds

Fabrication of Customized Ti6AI4V Heterogeneous Scaffolds with Selective Laser Melting: Optimization of the Architecture for Orthopedic Implant Applications.

Trabecular-like Ti-6Al-4V Scaffolds for Orthopedic: Fabrication by Selective Laser Melting and in Vitro Biocompatibility

Effect of Microarc Oxidation-Treated Ti6Al4V Scaffold Following Low-Intensity Pulsed Ultrasound Stimulation on Osteogenic Cells in Vitro

Influence of process parameters on the organization and properties of 316L-SCBCC bracket formed by selective zone laser melting

Effect of Post-Processing Methods on the Surface Quality of Ti6Al4V Fabricated by Laser Powder Bed Fusion

Preparation and mechanical performance analysis of porous Ti6Al4V scaffold fabricated by direct ink writing

Surface modification of porous titanium and titanium alloy implants manufactured by selective laser melting: A Review

Manufacturability study in laser powder bed fusion of biomedical Ti alloys for orthopedic implants: an investigation of mechanical properties, process-induced porosity and surface roughness