Abstract:CONSPECTUS: To tackle the foreseen energy crisis and serious environmental problem caused by conventional energy resources, solar cells, or photovoltaics (PV), a technology that can directly convert sunlight to electricity has been considered to be one of the most important and cost-effective clean energy techniques that benefit the environment. So far, silicon-based PVs have dominated the market due to mature fabrication techniques and their relatively good power conversion efficiency (PCE) and excellent stability. In the past decades, metal halide perovskite PVs have been a major direction of current PV research owing to their intriguing optoelectronic performance. The record PCE of perovskite PV cells has unprecedently increased from an original 3.8 to 25.5%. The typical structure of a photovoltaic perovskite is ABX(3), where A refers to a monovalent cation such as methylammonium (MA(+)), cesium (Cs+), or formamidinium (FA(+)); B refers to a divalent cation such as Pb2+ or Sn2+; and X refers to a halide anion. In general, a perovskite PV device consists of an active layer of the perovskite absorber, which is connected by a hole-transporting layer (HTL) and an electron-transporting layer (ETL). In the beginning, the strategies to improve the PCEs mainly focused on developing an effective method to grow a smooth and continuous polycrystalline film. After the improvement of the baseline PCE of the perovskite PVs, various techniques were employed to reduce the defects of perovskite formed at grain boundaries and surfaces, further pushing the PCEs of perovskite PV devices to over 20%. In the meantime, the discovery of suitable and low-cost interfacial materials such as electron-transporting materials and hole-transporting materials has appealed to the attention of the perovskite research community to accelerate the commercialization of the perovskite PVs. In this Account, we start from our efforts to develop facile and effective fabrication strategies to obtain smooth and continuous polycrystalline perovskite thin films, including vapor-assisted and moisture-assisted perovskite crystal growth. The strategies and the in-depth mechanisms of preventing the formation of specific detrimental defects accumulated at grain boundaries or the surface are also portrayed by designing various passivation molecules with certain functional groups, such as carbonyl groups, amine groups, or sulfonic groups. Some systematically designed electron- or hole-transporting materials to improve the charge extraction and collection efficiency in perovskite PV devices are discussed as well. Finally, future perspectives for further enhancing the long-term stability and PCE are proposed to accelerate the commercialization of perovskite PV devices in the next decade.

Moderate Hot Antisolvent Treatment for Efficient 2D Alternating Cation Perovskite Solar Cells

Antisolvent Engineering On Low-Temperature Processed Cspbi3 Inorganic Perovskites For Improved Performances Of Solar Cells

Stable 2D Alternating Cation Perovskite Solar Cells with Power Conversion Efficiency >19% via Solvent Engineering

Stable 2D Alternating Cation Perovskite Solar Cells with Power Conversion Efficiency >19% Via Solvent Engineering

Tailored Key Parameters of Perovskite for High-Performance Photovoltaics

Concerted regulation on vertical orientation and film quality of two-dimensional ruddlesden-popper perovskite layer for efficient solar cells

Antisolvents Treatment of Cs 0.15 FA 0.85 PbI 3 Boosting Efficiency for Perovskite Solar Cells

Green antisolvent additive engineering to improve the performance of perovskite solar cells

Enhanced Efficiency and Stability of Perovskite Solar Cells by 2D Perovskite Vapor-Assisted Interface Optimization

Stable Quasi‐2D Perovskite Solar Cells with Efficiency over 18% Enabled by Heat–Light Co‐Treatment

Solvation Effect in Precursor Solution Enables over 16% Efficiency in Thick 2D Perovskite Solar Cells

Synergistic Effect of Additives on 2D Perovskite Film Towards Efficient and Stable Solar Cell

Hot-Antisolvent Assisted Morphological Regulation of Perovskites for Semitransparent Photovoltaics Employing Hot-Pressing Approach

Acetic Acid Assisted Crystallization Strategy for High Efficiency and Long-Term Stable Perovskite Solar Cell

Tailoring Organic Cation of 2D Air‐Stable Organometal Halide Perovskites for Highly Efficient Planar Solar Cells

Molecular Engineering for Two-Dimensional Perovskites with Photovoltaic Efficiency Exceeding 18%

Improving Crystallization and Stability of Perovskite Solar Cells Using a Low-Temperature Treated A-Site Cation Solution in the Sequential Deposition

Highly Efficient Guanidinium‐Based Quasi 2D Perovskite Solar Cells Via a Two‐Step Post‐Treatment Process

Orientation Regulation of Phenylethylammonium Cation Based 2D Perovskite Solar Cell with Efficiency Higher Than 11%

Boosting efficiency and stability of 2D alternating cation perovskite solar cells via rational surface-modification: Marked passivation efficacy of anion

An efficient post-treatment strategy with acetylacetone for low temperature CsPbI2Br solar cells