Abstract:The interactions among thermal history, plastic deformation and residual stresses in the friction stir welding (FSW) process under different welding parameters have been widely considered a crucial issue and still not fully understood. In the present study, a novel three-dimensional fully coupled thermo-mechanical finite element (FE) model based on coupled Eulerian-Lagrangian approach (CEL) has been developed to simulate the FSW process of aluminium alloy AA 6082-T6 and to analyse the thermo-mechanical interaction mechanisms under different welding conditions. The numerical model successfully simulates the plunge, dwell, and welding steps in FSW and captures the evolution of temperature, plastic deformation, and residual stresses in the welded joint. The obtained results were validated by experimental testing with observed cross-weld thermal history, optical macrography and residual stress measurement using the neutron diffraction technique. The results reveal that the tool rotation speed governs the temperature evolution; the peak temperature increased from 740 to 850 °K when the tool rotation speed rose from 800 to 1100 rpm. The rotational speed also affected the plastic deformation, material flow, and the volume of material being stirred during the welding process. Higher plastic deformation is formed in the stirring zone by increasing the tool angular velocity. This behaviour led to an increase in the stirring effect of the welding tool, reduction of the tunnel defect size and enhancing the quality of weldments. The distribution of residual stresses in different zones of the FSW joints has been found to have an M-shaped profile. A significant tensile residual stress is characterised in the edge of the nugget zone in both longitudinal and transverse directions, balanced by compressive stresses in the thermo-mechanically affected zone, heat-affected zone and base metal. The presented FE modelling provides a reliable insight into the effects of the welding parameters on the weld quality of FSW joints and process optimisation with minimised experimental trials.

Effect of Tool-Workpiece Interface Temperature Control on the Weld Quality of a Bobbin-Tool Friction-Stir-welded Aluminum Alloy

Temperature-dependent friction coefficient and its effect on modeling friction stir welding for aluminum alloys

Temperature Monitoring and Material Flow Characteristics of Friction Stir Welded 2A14-t6 Aerospace Aluminum Alloy

Thermal Cycling, Microstructure, and Mechanical Properties of Al-Mg-Si-Cu Alloy Bobbin Tool Friction Stir Welded Joints Based on Thermal Index

Numerical and experimental study on the thermal process, material flow and welding defects during high-speed friction stir welding

Flow-coupled Thermo-Mechanical Analysis of Frictional Behaviors at the Tool-Workpiece Interface During Friction Stir Welding

Effects of Tool Tilt Angle on the In-Process Heat Transfer and Mass Transfer During Friction Stir Welding

Effects of tool pin thread on temperature field and material mixing in friction stir welding of dissimilar Al/Mg alloys

Finite-element Analysis of the Tool Tilt Angle Effect on the Formation of Friction Stir Welds

Effect of Temperature and Material Flow Gradients on Mechanical Performances of Friction Stir Welded AA6082-T6 Joints

Effects of Pin Thread on the In-Process Material Flow Behavior During Friction Stir Welding: A Computational Fluid Dynamics Study

Tool rotational speed impact on temperature variations, mechanical properties and microstructure of friction stir welding of dissimilar high-strength aluminium alloys

Influence of Friction Stir Processing on Weld Temperature Distribution and Mechanical Properties of TIG-Welded Joint of AA6061 and AA7075

Heat generation, plastic deformation and residual stresses in friction stir welding of aluminium alloy

Effect of tool revolutionary pitch on heat transfer and material flow in Al/steel friction stir lap welding

The effect of tool pin size and taper angle on the thermal process and plastic material flow in friction stir welding

Influence of welding parameters on the interface temperature field of TC4 titanium alloys/304 stainless steel friction stir lap joints

Numerical Study of Temperature Evolution During Friction Element Welding

Development of Computational Approach for Analyzing In-Process Thermal-Mechanical Condition during Friction Stir Welding for Prediction of Material Bonding Defect

Thermal Analysis of Friction Stir Welding Process under Different Control and Energy Parameters

The performance of a Co-based alloy tool in the friction stir welding of TA5 alloy