Abstract:Inorganic chloroaluminate molten salts are of interest as electrolytes for the high-rate plating of aluminum because of their high conductivity and low cost. Unfortunately, low-melting Lewis acidic inorganic chloroaluminate molten salts such as AlCl3-rich AlCl3-NaCl are problematic because of the loss of volatile AlCl3, which restricts their use to sealed systems. Most common Lewis neutral chloroaluminate salts that are based on a single alkali chloride salt, e.g., equimolar AlCl3-NaCl or NaAlCl4, are problematic as well because of their high melting points. However, Hjuler et al.1 described a complex mixture of inorganic haloaluminate salts, LiAlCl4-NaAlCl4-NaAlBr4-KAlCl4 (3:2:3:2) [or LiAlBr4-NaAlCl4-KAlCl4 (3:5:2)] with a melting point of only 86 oC. This Lewis neutral salt was originally formulated for use as an electrolyte for rechargeable Al/molten salt/Ni3S2batteries. The facile electrodeposition of aluminum from this salt was also demonstrated. Any electrolyte solution that is used for the continuous electrodeposition or plating of aluminum normally requires an aluminum anode to resupply the aluminum species that is reduced at the cathode and lost from the solution during the plating process. Much research has been directed at the mechanism of the plating reaction at the cathode in haloaluminate melts, but little attention has been directed to the reactions taking place at the anode. As described in a now classical paper by Holleck and Giner,2passivation phenomena at the aluminum anode may ultimately limit the rate of the plating process in these molten salts as well as their use as battery electrolytes. In this presentation, we describe the behavior of the aluminum anode in the LiAlCl4-NaAlCl4-NaAlBr4-KAlCl4 molten salt at 130 oC. The anodization of Al in this melt is a complex process. Figure 1 shows current - time plots recorded at an Al rotating disk electrode at different applied potentials, E app, versus the equilibrium potential, E eq. (0 V versus Al). As shown in the Levich plots in Fig. 2, for E appup to 0.60 V, the anodization of Al is a mass transport-limited process according to the well-known reversible reaction: Al + 7AlX4 - ↔ 4Al2X7 - + 3e- (1) where X = Cl + Br. However, as E app is increased above this value, the current decreases significantly over a short time period, indicating that the amount of AlX4 - supplied by mass transport is not sufficient to support the reaction in Eq. 1. This results in passivation of the Al anode with AlX3(s) according to the reaction Al + 3AlX4 - ↔ 4AlX3(s) + 3e- (2) Once the Al electrode develops a passive layer, the current reaches a steady-state value determined by the rate of AlX3(s) formation (Eq. 2) and dissolution according to the reaction AlX3(s) + AlX4 - ↔ Al2X7 - (3) The Levich plot in Figure 2 suggests that this dissolution process is also mass transport limited. References 1H. A. Hjuler, S. von Winbush, R. W. Berg, and N. J. Bjerrum, J. Electrochem. Soc., 136, 901-906 (1989). 2G. L. Holleck and J. Giner, J. Electrochem. Soc., 119, 1161-1166 (1972). Acknowledgement This work was funded by the Strategic Environmental Research and Development Program (SERDP) through contract DE-AC05-00OR22725 to Oak Ridge National Laboratory with subcontract to the University of Mississippi.

Alumina Solubility in Na_3AlF_6-K_3AlF_6-AlF_3 Molten Salt System Prospective for Aluminum Electrolysis at Lower Temperature

Alumina Solubility and Dissolution Rate in NaF-KF-AlF3-LiF-CaF2 Low-Temperature Electrolyte

Micro-structure studies of the molten binary K3AlF6–Al2O3 system by in situ high temperature Raman spectroscopy and theoretical simulation

Study on the Structure and Transport Properties of Molten Salts of NaF–KF–AlF3 Electrolytes by First-Principles Molecular Dynamics Simulation

Electrical Conductivity of Low-Temperature KF-Naf-AlF3 Melts with CaF2 and Al2O3 Addition

Reduction of the Operating Temperature of Aluminum Electrolysis: Low Temperature Electrolyte

Molecular Dynamics Investigation on Structural and Transport Properties of Na3AlF6–Al2O3 Molten Salt

Phase Equilibrium in the Ternary System K2O–Al2O3–H2O at 323.15, 333.15, 343.15, and 353.15 K

Study on the dissolution of aluminium carbide formed on the graphite cathode in aluminium electrolysis

Approach of the Molten Salt Chemistry for Aluminium Production: High Temperature NMR Measurements, Molecular Dynamics and DFT Calculations

Dissolution characteristics of black aluminum dross in Na3AlF6-AlF3-Al2O3 molten salt system

Estimation of the proportions of aluminum-fluorine species in NaF-AlF 3 mixtures by in situ Raman spectroscopy and theoretical simulations

Corrosion of Two Iron-Based Aluminaforming Alloys in NaCl-MgCl2 Molten Salts at 600 °C

Chemical Properties of Chromium Oxide in KF-NaF-AlF3 Based Low Temperature Electrolyte Melt

Aluminum Anodization in the Low-Melting LiAlBr4-NaAlCl4-KAlCl4 Molten Salt

LOW-TEMPERATURE ELECTROLYTIC PRODUCTION OF Al-REM ALLOYS IN CRYOLITE MELTS

Structural correlation and chemistry of molten NaF–ScF3 with dissolved metal aluminium: TG/DTA, XRD, NMR and molecular dynamics simulations

Performance Evaluation of Low-Temperature KF-NaF-AlF₃ Electrolytes for Aluminum Electrolysis Using Vertical Inert Cu-Ni-Fe Alloy Anodes

Mass- and Heat Transfer During Dissolution of Alumina

Ion-ion interactions enhance aluminum solubility in alkaline suspensions of nano-gibbsite (α-Al(OH)3) with sodium nitrite/nitrate

Impurity Behavior in Aluminum Extraction by Low-Temperature Molten Salt Electrolysis