Abstract:In recent decades, geoelectrical methods have played a very important role in near-surface investigation. The most widely used of these methods is electrical resistivity tomography (ERT). Regardless of the forward and inversion algorithms used, the original data collected from a survey is the most important factor for quality of the resulted model. However, 3D electrical resistivity survey design continues to be based on data sets recorded using one or more of the standard electrode arrays. There is a recognized need for the 3D survey design to get better resolution using fewer data. Choosing suitable data from the comprehensive data set is a great approach. By reasonable selecting, better resolution can be obtained with fewer electrodes and measurements than conventional arrays. Previous research has demonstrated that the optimized survey design using the 'Compare R' method can give a nice performance.This paper adds target-oriented selection and modified the original 'Compare R' method. The survey design should be focused on specific target areas, which need a priori information about the subsurface properties. We select electrodes and configurations as the target set by the comprehensive set firstly which meets the requirements of the target area. The number of measurements and electrodes is much less than the comprehensive set and the model resolution matrix takes less time to calculate. At the next step for rank, we calculate the sensitivity matrix of the target set only once and then calculate the contribution degree of each measurement separately from it. The time of iterative calculation of the resolution matrix when measurements set changing is less than the original method.The traditional method of evaluating RMS is not appropriate for comparing the quality of collected data by different survey designs. SSIM (structural similarity index) gives more reliable measures of image similarity better than the RMS. The curves of SSIM values in three dimensions and the average SSIM are given as quantitative comparisons. Besides, the frequency of electrodes utilized given to guides on selecting the highest used electrodes. Finally, the curves of the average relative resolution S and the number of electrodes as the number of measurements increase are given, which proves the method works effectively.The results show the significance of using target-oriented optimized survey design, as it selects fewer electrodes and arrays than the original CR method. Also, it produces better resolution than conventional arrays and takes less calculation time. 3D SSIM, frequency of electrodes used, the relationship between average relative resolution, number of electrodes and number of measurements, these quantitative comparison methods can effectively evaluate the data collected in various survey designs.

3D ELECTRICAL RESISTIVITY INVERSION TOMOGRAPHY WITH SPATIAL STRUCTURAL CONSTRAINT

Target-oriented Optimized Survey Design and Quantitative Comparison for 3D Electrical Resistivity Tomography

Strategy for Optimization of Arbitrary Electrode Distribution for 3D Electrical Resistivity Tomography in Urban Zones

Application of Three-Dimensional Electrical Resistivity Tomography in Urban Zones by Arbitrary Electrode Distribution Survey Design

Analysis Of Integrating Ert Data Of Different Array Types: Simulation Study And Observations On An Archaeological Site

Image-guided structure-constrained inversion of electrical resistivity data for improving contaminations characterization

Three-Dimensional Inversion of Borehole-Surface Resistivity Method Based on the Unstructured Finite Element

Two-Dimensional Joint Inversion of Seismic Velocity and Electrical Resistivity Using Seismic Travel Times and Full Channel Electrical Measurements Based on Alternating Cross-Gradient Structural Constraint

Three-Dimensional Anisotropic Inversion for Direct Current Resistivity Method Using Unstructured Tetrahedral Discretization

3D modeling and inversion of the electrical resistivity tomography using steel cased boreholes as long electrodes

3D inversion of 2D electrical resistivity data for geotechnical analysis

Research and application of joint-constrained inversion of transient electromagnetic multivariate parameter

3-D Structurally Constrained Inversion of the Controlled-Source Electromagnetic Data Using Octree Meshes

3-D Cross-Gradient Joint Inversion of Seismic Refraction and Dc Resistivity Data

Two-dimensional Inversion of CSAMT Data and Three-Dimensional Geological Mapping for Groundwater Exploration in Tongkeng Area, Hunan Province, China

An efficient joint inversion strategy for 3D seismic travel time and DC resistivity data based on cross-gradient structure constraint

Quasi-2D inversion of surface large fixed-loop transient electromagnetic sounding data

Three-dimensional inversion analysis of transient electromagnetic response signals of water-bearing abnormal bodies in tunnels based on numerical characteristic parameters

Sensitivity study on two-dimensional and three-dimensional magnetotelluric inversions

Two-dimensional Inversion of DC Resistivity Data on Unstructured Grids Using Fuzzy C-means Clustering Model Constraint

Multiscale 3-D Stochastic Inversion of Frequency-Domain Airborne Electromagnetic Data