Research on Finger Position Control of DLR/HIT Hand

Jingdong Zhao

2009-01-01

Abstract:Finger position control is base of force control and dexterous manipulation with multi-finger.Coordinate and layered control space of a finger for DLR/HIT hand have been build.Based on sliding mode control and trajectory planning,finger position control in joint space and cartesian space is designed and achieved.

What problem does this paper attempt to address?

Impedance Control of Single Finger of the HIT/DLR Dextrous Robot Hand

LIU Yi-wei,JIN Ming-he,YANG Lei

DOI: https://doi.org/10.3969/j.issn.1001-2257.2005.10.021

2005-01-01

Abstract:Using 6 DOFs force/torque sensor,the cartesian position based impedance control of single finger is implemented.According to the force/torque sensing information of the fingertip sensor,reference position will be modified in term of aim impedance model,and the inner position controller is used to control the finger to follow anticipant track.
A stable grasping control strategy for HIT/DLR multi-fingered hand

Bin Wang,Li Jiang,Hong Liu

DOI: https://doi.org/10.3321/j.issn:1671-4512.2007.12.020

2007-01-01

Abstract:A new position/torque control strategy for multi-fingered dexterous hand stable grasping was proposed. Based on impedance control, the position signal was added to the torque control and a system observer was used for the switch between these two control models. Both trajectory tracking in free space and precise torque tracking in constrained space could be realized respectively. Because the kernel control model was the same during the transition, the stability could be assured and precise grasping force of the multi-fingered hand could be realized in constrained space. Experimental results show the effectiveness and feasibility of the control strategy.
A new control strategy for DLR's multisensory articulated hand

Hong Liu,J. Butterfass,S. Knoch,P. Meusel,G. Hirzinger

DOI: https://doi.org/10.1109/37.753935

1999-04-01

IEEE Control Systems

Abstract:Concerns a multisensory 12-DOF 4-finger hand in which all actuators are integrated in the palm or the fingers. It was necessary to use a specially designed miniaturized linear actuator. For telemanipulation our first approach was to make the hand follow the desired states commanded from higher levels, e.g., dataglove. This requires accurate tracking, compliance in the constrained environment, and smooth transition between these two modes. The tracking control problem is to design a control scheme which generates the appropriate control signal so as to ensure that the joint angle follows any specified reference trajectory as closely as possible. Compliance is needed for fine manipulation and also for the protection of the hand. Transition control is essentially the problem of making the energy conversion more effective and smooth. We propose a parallel torque/position control strategy for this task. The robust trajectory tracking in free space is implemented by sliding mode control; the compliant motion in the constrained environment is realized by using impedance control; and a parallel observer based on contact torques and system states has been built to determine the switch between these two kind of controllers for the transition control from or to contact motion.
Research on Fingers of HIT Dexterous Robot Hand and Impedance Control

Liu Yijun,Liu Yiwei

DOI: https://doi.org/10.3969/j.issn.1000-4998.2008.07.002

2008-01-01

Abstract:The finger with flexibility in touching is a key factor in multi-finger dexterous manipulation.The resistance control is one of the main methods to realize the robot flexible control.Based on the fingers of HIT dexterous robot hand,design of their force/torque sensors is described,including a finger tip 6D force/torque sensor and two articulation torque sensors.With the finger tip 6D force/torque sensor acting as force feedback,the resistance control in Cartesian space is implemented.
Multi- fingered manipulation with HIT/DLR hand

Ping HE,Xiao-hui GAO,Lei YANG,Hong LIU,He-gao CAI

DOI: https://doi.org/10.3321/j.issn:0367-6234.2005.11.028

2005-01-01

Abstract:A new approach to construct the position/orientation mapping between finger joints and a manipulated object during the grasping of an HIT/DLR hand is presented and the complete kinematic equations of the hand are given with plane grasping manipulation. A hierarchical structure is adopted to simplify the resolution of the kinematics and is helpful in preventing kinematic computation from big matrices, such as the grasping matrix and the hand Jacobian matrix. Finally, a grasping manipulation with an HIT/DLR hand was carried out and the experimental results proved that the new kinematic algorithm could satisfy the position control requirement of grasping manipulation.
Autonomous Control of Multi-Fingered Hand

Li Jiang,Hong Liu

DOI: https://doi.org/10.1080/10020070612330031

2006-01-01

Abstract:This paper describes a novel autonomous control strategy of multi-fingered hand based on a modular control system of dexterous manipulation. A simple proportional-integral-derivative (PID) position control with friction compensation, which requires few friction parameters, is used to realize accurate and smooth trajectory tracking in pregrasp phase. In grasp and manipulation phases, an event-driven switcher is adopted to determine the switching between unconstrained position control and constrained torque control, and an improved explicit integral force control strategy is implemented to realize Simultaneously stable contact transition and accurate force tracking. Experimental results have verified the effectiveness of the proposed autonomous control strategy of multi-fingered hand.
Research on control system for 5-DOFs humanoid prosthetic hand with force/position sensing

Fan Zhongbin,Jiang Li,Liu Hong

DOI: https://doi.org/10.3969/j.issn.2095-2783.2010.08.001

2010-01-01

Abstract:A control system was designed for the 5-DOFs (degrees of freedom) humanoid prosthetic hand with force/position sensing that can be actuated individually. The control system has the hierarchical control structure. The bottom controller is based on the DSP+CPLD architecture and can realize the motion control of the prosthetic hand. The controller is integrated in the prosthetic hand body, and the high-level integration of the prosthetic hand is achieved. Based on the position-based impedance control strategy, a target damping coefficient online-adjusting impedance control method is proposed. The method improves the performance of the impedance control system for the prosthetic hand.
The Task-Orientated Control System of a Dexterous Robot Hand with a Multi-Fingered Spatial Coordinating Impedance Control

CHEN Zhaopeng,JIN Minghe,FAN Shaowei,LIU Yiwei,WU Ke,JIANG Li,LIU Hong

DOI: https://doi.org/10.3969/j.issn.1006-7043.201105063

2012-01-01

Abstract:In order to improve the control and manipulation performance,this paper presented a centralized-controller/ decentralized-data-processing real time control architecture for the DLR/HIT II dexterous robot hand,and established a Simulink/QNX-based real time control platform along with an embedded drive control layer.These improvements significantly simplified the development procedure of a controller for a highly integrated mechatronic robot hand,and provided a seamless interface between the dexterous robot hand and multi-DoF humanoid robots.By utilizing the positions of fingertips,this paper proposed an object level frame for an n-fingered robot hand.In order to control the position and pose of the object being grabbed,a spatial coordination impedance controller has been implemented based on 6-DoF spatial virtual spring stiffness and joint torque feedback.The experiments were carried out on a Simulink/QNX-based real time control platform with the proposed real time control system on the DLR/HIT II robot hand.Experimental results show the effectiveness of the designed control system and spatial impedance controller.The control inputs for grasping and manipulation have been reduced to 6 other than the 30 needed for a 5-fingered robotic hand DLR/HIT II.
Experimental Evaluation of Cartesian and Joint Impedance Control with Adaptive Friction Compensation for the Dexterous Robot Hand DLR-Hit II.

Zhaopeng Chen,Neal Y. Lii,Thomas Wimboeck,Shaowei Fan,Hong Liu

DOI: https://doi.org/10.1142/s0219843611002605

2011-01-01

International Journal of Humanoid Robotics

Abstract:This paper presents impedance controllers with adaptive friction compensation for the five-finger dexterous robot hand DLR-HIT II in both joint and Cartesian space. An FPGA-based control hardware and software architecture with real-time communication is designed to fulfill the requirements of the impedance controller. Modeling of the robot finger with flexible joints and mechanical couplings in the differential gear-box are described in this paper. In order to address the friction due to the complex transmission system and joint coupling, an adaptive model-based friction estimation method is carried out with an extended Kalman filter. The performance of the impedance controller with both adaptive and parameter-fixed friction compensations for the robot hand DLR-HIT II are analyzed and compared in this paper. Furthermore, gravity estimation is implemented with Least Squares technique to address uncertainties in gravity compensation due to the close proximity and complexity of robot hand components. Experimental results prove that accurate position tracking and stable torque/force response can be achieved with the proposed impedance controller with friction compensation on five-finger dexterous robot hand DLR-HIT II.
A Novel Grasping Force Control Strategy for Multi-Fingered Prosthetic Hand

Ting Zhang,Li Jiang,Hong Liu

DOI: https://doi.org/10.1007/s11771-012-1173-4

2012-01-01

Journal of Central South University

Abstract:A grasping force control strategy is proposed in order to complete various fine manipulations by using anthropomorphic prosthetic hand. The position-based impedance control and force-tracking impedance control are used in free and constraint spaces, respectively. The fuzzy observer is adopted in transition in order to switch control mode. Two control modes use one position-based impedance controller. In order to achieve grasping force track, reference force is added to the impedance controller in the constraint space. Trajectory tracking in free space and torque tracking in constrained space are realized, and reliability of mode switch and stability of system are achieved. An adaptive sliding mode friction compensation method is proposed. This method makes use of terminal sliding mode idea to design sliding mode function, which makes the tracking error converge to zero in finite time and avoids the problem of conventional sliding surface that tracking error cannot converge to zero. Based on the characteristic of the exponential form friction, the sliding mode control law including the estimation of friction parameter is obtained through terminal sliding mode idea, and the online parameter update laws are obtained based on Lyapunov stability theorem. The experiments on the HIT Prosthetic Hand IV are carried out to evaluate the grasping force control strategy, and the experiment results verify the effectiveness of this control strategy.
Control System for DLR/HIT II Dexterous Robot Hand and Synchronized Control for Base Joint

兰天,刘伊威,金明河,姜力,樊绍巍,刘宏

DOI: https://doi.org/10.3969/j.issn.1007-449x.2009.04.025

2009-01-01

Abstract:A DSP＆FPGA-based multilevel control system was developed for multi-sensory and multi-DOF dexterous robot hand, in which the drive, control and sensor systems were integrated in the finger. So the five-finger DLR/HIT II dexterous robot hand that resembled the human hand regarding size and movability was realized. A synchronized cross-coupled controller for base joint of dexterous robot hand was designed, including feedforwards of velocity and acceleration, feedbacks of synchronous errors and position errors, and a smooth robust nonlinear feedback compensator. The controller did not require the explicit use of the system dynamic model. Compared with conventional non-synchronized PD friction compensation and trajectory tracking control, experimental results demonstrate the validity of the designed control system and synchronized cross-coupled controller.
Experimental Analysis on Spatial and Cartesian Impedance Control for the Dexterous DLR/Hit II Hand

Zhaopeng Chen,Neal Y. Lii,Thomas Wimboeck,Shaowei Fan,Hong Liu,Alin Albu-Schaeffer

DOI: https://doi.org/10.2316/journal.206.2014.1.206-3669

2014-01-01

International Journal of Robotics and Automation

Abstract:This paper presents an experimental study on impedance control in both Cartesian and object level with adaptive friction compensation for dexterous robot hand based on joint torque feedback. To adaptively decrease the effects of high friction caused by complex transmission systems and joint coupling, a friction observer is proposed based on the extended Kalman filter (EKF) in this paper. A Cartesian impedance controller is implemented on a multi-fingered dexterous robot hand with identical fingers, based on the modelling of each modular finger. In addition, a flexible n-fingered object frame is proposed in this paper, applicable to any finger configuration with three or more fingers (n ≥ 3). This enables the design of a 6-DoF spatial impedance controller. Stability of the closedloop system with friction observer is analysed. A position error of less than 0.16 ◦ is achieved using joint impedance control with adaptive friction compensation, which shows significant improvement in performance, as compared to 1.5 ◦ without compensation, and 0.5 ◦ with fixed-parameters friction compensation. Experimental results confirm the improvement in performance for the robot hand with Cartesian impedance control and adaptive joint friction compensation, demonstrating the effectiveness of spatial impedance controller with the proposed object frame and estimation strategy.
STUDY OF POSITION AND TORQUE FEEDBACK CONTROL SYSTEM OF MULTI-FINGERED DEXTEROUS ROBOT HAND

何平,金明河,刘宏,谢宗武

DOI: https://doi.org/10.3321/j.issn:1002-0446.2002.04.006

2002-01-01

ROBOT

Abstract:There was more research on single DOF of single finger than on the basejoint that has two DOFs. This paper gives a brief description of HIT-1 hand, a multi-fingered dexterous hand, and simply analyzes the base joint's kinematics and dynamics model. Then the position and torque feedback control system is constructed based on the model analysis. The traditional PID algorithm has been employed to complete both position control in free space and torque control in constrained environment, and some experimental results has been analyzed.
Adaptive Impedance Control for Dexterous Robot Hand with Elastic Joint

FAN Shao-wei,ZONG Hua,QIU Jing-hui,CHEN Zhao-peng

DOI: https://doi.org/10.3969/j.issn.1007-449x.2012.12.013

2012-01-01

Abstract:This paper present recent results on the joint and Cartesian space impedance control for five-finger dexterous robot hand DLR-HIT Ⅱ with elastic joints,based on joint torque feedback and nonlinearity compensation.Passivity based control strategy was implemented on HIT/DLR Ⅱ dexterous robot hand,with modeling of the elastic joint on the robot hand.To improve the performance of the impedance controller,adaptive friction estimation with extended Kalman filter and gravity compensation based on Least Squares have been investigated on the robot hand.Experimental results show that,for the harmonic drive robot hand with joint torque feedback,accurate position tracking and stable torque/force response can be achieved with Cartesian and joint impedance controller with adaptive friction compensation.
Modeling and Precision Motion Control of Dexterous Object In-Hand Rotation

Jiawei Li,Lu,Cong Wang

DOI: https://doi.org/10.1109/icmech.2019.8722903

2019-01-01

Abstract:This paper presents the modeling and precision motion control of an important class of dexterous object in-hand rotation by three-fingered robot hand. First, we explicitly construct the planar friction model between the fingertip and the object. Then, to precisely regulate the object angle to its desired value while minimizing the deviation of the object center with respect to the fingertip, we propose a novel hybrid control structure consisting of two modules - regular tracking control module and the motion re-planning module. The proposed approach naturally mimics the human motor behavior when rotating an object to a desired angle by pushing and re-positioning the fingers. Finally, a simulation study is also performed by using a high-fidelity virtual physics engine “MuJoCo” to verify the effectiveness of the proposed approach.
Experimental Study on Impedance Control for the Five-Finger Dexterous Robot Hand DLR-HIT II.

Zhaopeng Chen,Neal Y. Lii,Thomas Wimboeck,Shaowei Fan,Minghe Jin,Christoph H. Borst,Hong Liu

DOI: https://doi.org/10.1109/iros.2010.5649356

2010-01-01

Abstract:This paper presents experimental results on the five-finger dexterous robot hand DLR-HIT II, with Cartesian impedance control based on joint torque and nonlinearity compensation for elastic dexterous robot joints. To improve the performence of the impedance controller, system parameter estimations with extended kalman filter and gravity compensation have been investigated on the robot hand. Experimental results show that, for the harmonic drive robot hand with joint toruqe feedback, accurate position tracking and stable torque/force response can be achieved with cartesian and joint impedance controller. In addition, a FPGA-based control architecture with flexible communication is proposed to perform the designed impedance controller.
Cartesian Impedance Control On Five-Finger Dexterous Robot Hand Dlr-Hit Ii With Flexible Joint

Zhaopeng Chen,Neal Y. Lii,Minghe Jin,Shaowei Fan,Hong Liu

DOI: https://doi.org/10.1007/978-3-642-16584-9_1

2010-01-01

Abstract:This paper presents an impedance controller for five-finger dexterous robot hand DLR-HIT II, which is derived in Cartesian space. By considering flexibility in finger joints and strong mechanical couplings in differential gear-box, modeling and control of the robot hand are described in this paper. The model-based friction estimation and velocity observer are carried out with an extended Kalman filter, which is implemented with parameters estimated by Least Squares Method. The designed estimator demonstrates good prediction performance, as shown in the experimental results. Stability analysis of the proposed impedance controller is carried out and described in this paper. Impedance control experiments are conducted with the five-finger dexterous robot hand DLR-HIT II in Cartesian coordinates system to help study the effectiveness of the proposed controller with friction compensation and hardware architecture.
Dsp&Fpga-Based Joint Impedance Controller For Dlr/Hit Ii Dexterous Robot Hand

Tian Lan,Yi Liu,Minghe Jin,Shaowei Fan,HongGen Fang,Jinjun Xia,Hong Liu

DOI: https://doi.org/10.1109/AIM.2009.5229817

2009-01-01

Abstract:A position-based joint impedance controller and a DSP&FPGA-based multilevel control structure were developed to improve the capabilities of robot hand performing task in a variety of environments. Based on finite element analysis technologies, the new torque sensors and giant magnetoresistance (GMR) position sensors were designed and applied, and meet the challenge of joint torque measuring and position measuring. The experimental results of joint impedance control show that proposed strategy not only improves the effectiveness of contact task performance, but also provides compliant interaction of robot hand with a person, thus enables robot hand to work in different environments.
Fuzzy Control Based On Double Position Feedback For Multi-Fingered Dexterous Hand

Yq He,Gc Zhu,Yy Luo,Qx Zhang

2001-01-01

Abstract:A fuzzy control scheme based on double position feedback for multi-fingered dexterous hand is presented. In the inner closed loop, general PID control method based on encoder feedback of motor is adopted, and in the outer closed loop, a new fuzzy control based on position feedback of joint is adopted. In the two-layered position feedback control scheme, the nonlinear tendon-driven system is included in the outer closed loop. Compared with half closed loop structure which has only encoder feedback it can improve stability and robustness of control system. Experiment verify that the control scheme can improve tracking accuracy obviously.
Design of a Novel Finger of DLR/HIT Dextrous Robot Hand Based on Mechatronic Integration

LIU Yi-wei,LIU Hong,JIANG Li,JIN Ming-he,Wei Ran

DOI: https://doi.org/10.3321/j.issn:0367-6234.2005.08.002

2005-01-01

Abstract:With the idea of mechatronic integration,a novel finger of the dextrous robot hand has been designed. The finger with nice envelop has four joints with three DOFs driven by three brushless DC motors with smaller size and more torque. The use of rigid gear head,bevel gears and linkage in the transmission system makes the finger more rigid. Abundant sensors such as joint angle sensors,joint torque sensors and temperature sensors are located in the finger. Integration and modularization are achieved at most by high integration of finger body,driving system,sensors and electronics.

Research on Finger Position Control of DLR/HIT Hand

Impedance Control of Single Finger of the HIT/DLR Dextrous Robot Hand

A stable grasping control strategy for HIT/DLR multi-fingered hand

A new control strategy for DLR's multisensory articulated hand

Research on Fingers of HIT Dexterous Robot Hand and Impedance Control

Multi- fingered manipulation with HIT/DLR hand

Autonomous Control of Multi-Fingered Hand

Research on control system for 5-DOFs humanoid prosthetic hand with force/position sensing

The Task-Orientated Control System of a Dexterous Robot Hand with a Multi-Fingered Spatial Coordinating Impedance Control

Experimental Evaluation of Cartesian and Joint Impedance Control with Adaptive Friction Compensation for the Dexterous Robot Hand DLR-Hit II.

A Novel Grasping Force Control Strategy for Multi-Fingered Prosthetic Hand

Control System for DLR/HIT II Dexterous Robot Hand and Synchronized Control for Base Joint

Experimental Analysis on Spatial and Cartesian Impedance Control for the Dexterous DLR/Hit II Hand

STUDY OF POSITION AND TORQUE FEEDBACK CONTROL SYSTEM OF MULTI-FINGERED DEXTEROUS ROBOT HAND

Adaptive Impedance Control for Dexterous Robot Hand with Elastic Joint

Modeling and Precision Motion Control of Dexterous Object In-Hand Rotation

Experimental Study on Impedance Control for the Five-Finger Dexterous Robot Hand DLR-HIT II.

Cartesian Impedance Control On Five-Finger Dexterous Robot Hand Dlr-Hit Ii With Flexible Joint

Dsp&Fpga-Based Joint Impedance Controller For Dlr/Hit Ii Dexterous Robot Hand

Fuzzy Control Based On Double Position Feedback For Multi-Fingered Dexterous Hand

Design of a Novel Finger of DLR/HIT Dextrous Robot Hand Based on Mechatronic Integration