Two Orbit Operation at Bessy II - During a User Test Week
P. Goslawski,F Molisch Andreas,Felix Armborst,T. Atkinson,J. Feikes,Andreas Jankowiak,Ji Li,Tom Mertens,Markus Ries,Andreas Schälicke,G. Schiwietz,G. Wüstefeld
DOI: https://doi.org/10.18429/jacow-ipac2019-thyyplm2
2019-01-01
Abstract:Operating a storage ring close to a horizontal resonance and manipulating the transverse non-linear beam dynamics can generate stable Transverse Resonance Island Buckets (TRIBs), which give a 2nd stable orbit in the ring. Both orbits can be populated with different electron bunch filling patterns and provide two different radiation sources to the user community. Such a machine setting has been established at BESSY II and was tested under realistic user conditions in a first ‘TRIBs/Two Orbit User Test Week’ in February 2018. Results and user feedback will be discussed in this contribution. INTRODUCTION & MOTIVATION Fig. 1 shows the source point image when both orbits are populated with electron bunches. The main purpose of all TRIBs studies [1–4] at BESSY II is to carry out all the necessary proof-of-principle experiments to verify if a realistic two orbit user operation mode with TopUp injection is possible. Figure 1: Source point image from a X-ray pinhole camera at a ring dipole at a 1/3 integer resonance. The central beam spot belongs to the main orbit and the three outer spots to the island orbit. The diverse user community of a storage ring based synchrotron light source sets different and often even contradicting demands on the radiation source. High average brightness and photon flux-hungry experiments led to the development of Diffraction Limited Storage Rings using low emittance multi-bend-achromat (MBA) lattices in order to provide transverse coherent radiation. On the other hand time-resolved experiments focus on other parameters such as: photon pulse length for high temporal resolution, which drives the BESSY VSR [5] upgrade project and photon pulse repetition rate for coincidence, relaxation, time-of-flight and pump-probe experiments. ∗ Work supported by BMBF, Verbundforschung † paul.goslawski@helmholtz-berlin.de For the upcoming MBA light sources, so far, only very long bunches of a few hundred pico-seconds length in a homogeneous multi bunch (MB) filling are foreseen to avoid reduced lifetime, intra-beam scattering and collective instabilities. This will make time-resolved experiments more difficult at these facilities, which has already triggered an ongoing discussion and the request for timing modes with different pulse repetition rates [6]. The pulse repetition rate can be easily changed in a storage ring based light source by changing the stored filling pattern. The lowest repetition rate is achieved when only one electron bunch is stored in the ring in a so called Single Bunch (SB) operation mode. Since the bunch moves nearly with the velocity of light the lowest repetition rate is given by the circumference, i.e., the orbital period, of the ring. At BESSY II with 240 m, it is 1.25 MHz (=̂ 0.8 μs). The highest repetition rate is provided when all buckets are filled. It is given by the frequency of the radio frequency system frf, which each turn restores the energy electrons lost during radiation. Many storage rings operate with frf = 500 MHz (=̂ 2 ns bunch spacing) as BESSY II, others at 100 MHz (=̂ 10 ns bunch spacing) as MAX IV. Time-resolved experiments require repetition rates from 0.2 MHz to 20 MHz. Single bunch or few bunch fillings fulfill this requirement [7] to a large extent, but due to the lack of intensity needed for the average brightness experiments, they are offered only for a few weeks per year. Photon pulse and electron bunch separation techniques are an other approach to fulfill the requirements for high average brightness and flexibility in repetition rate, simultaneously. Therefore, at some facilities an advanced electron fill-pattern is stored in the ring [8] and in the best case at each beamline the user can choose the desired radiation source for his experiment. Temporal separation of photon pulses is realized locally at each beamline by blocking and passing photon pulses with mechanical choppers such as rotating discs with slits or with electro-acoustic choppers based on the grazing incidence x-ray diffraction on fast switching surface acoustic waves. Spatial separation of electron bunches in the ring is a more efficient and elegant way to provide different repetition rates, since the radiation sources are already intrinsically spatial separated, in the best case available at all beamlines. Two different methods have been established so far: a) the vertical kicking of one bunch of the filling pattern on another vertical orbit with a fast kicker magnet and b) the PPRE, PulsePicking-Resonant-Excitation, method. Here, one bunch of the filling is blown up by quasi-resonant excitation in the horizontal plane. By blocking the central part of the radiation of all bunches and accepting only light from the bloated 10th Int. Particle Accelerator Conf. IPAC2019, Melbourne, Australia JACoW Publishing ISBN: 978-3-95450-208-0 doi:10.18429/JACoW-IPAC2019-THYYPLM2 MC2: Photon Sources and Electron Accelerators A05 Synchrotron Radiation Facilities THYYPLM2 3419 Co nt en tf ro m th is w or k m ay be us ed un de rt he te rm so ft he CC BY 3. 0 lic en ce (© 20 19 ). A ny di str ib ut io n of th is w or k m us tm ai nt ai n at tri bu tio n to th e au th or (s ), tit le of th e w or k, pu bl ish er ,a nd D O I