Abstract:This article investigates the microstructure evolution, phase formation, and magnetic properties of Co2FeCr0.5Alx (x = 0.9, 1.2) complex component alloys, as a function of heat treatment temperatures (at 500, 600, 700, and 1150°C), using XRD, optical microscopy, electron microscopy and vibrating sample magnetometry (VSM). The alloy with 20.4 at% Al (x= 0.9), identified here as C1, consisted of microscale BCC1 phase and BCC nanoscale particles containing mainly Fe and Cr, and B2 matrix with mainly Al and Co. Partial transformation of the BCC1 phase to an FCC phase was observed at 700°C and full transformation at 1150°C, through twinning. For the sample with 25.5 at% Al (x= 1.2), identified as sample C2, there were only nanoscale BCC particles in the B2 matrix with the same element segregation between the phases as C1. This increase in Al (from x= 0.9 to 1.2) content stabilised the B2 matrix phase, reduced the grain size, and increased both saturation magnetisation (Ms) and coercivity (Hc). Moreover, increasing the heat treatment temperature resulted in an increase in grain size of the B2 matrix, volume fraction and average size of the micro BCC 1 and nanoscale BCC phases for both C1 and C2, which also modified the soft magnetic properties, with Ms and Hc increasing up to 600°C followed by a decrease until 1150°C. Using the structural information as inputs for density functional theory calculations of Hc and Ms, it has been found that the Hc is influenced by the grain size of the matrix, and the volume fraction and size of the BCC1 phase at temperature higher than 600°C for C1 and 700°C for C2, but is controlled by nanoscale BCC particles below these temperatures. The Ms is controlled by the elemental diffusion and segregation. Thus, the best combination of Hc and Ms was seen with antiferromagnetic Cr segregated and partitioning in the microscale BCC1 phase, and a B2 matrix with less Cr rich precipitation, formed at 500°C, where the misfit strain between B2 matrix and nanoscale BCC was low.

Phase Selection and Mechanical Properties of CoCrFexNiMn Multicomponent Alloys with Equivalent Electron Concentrations

Effect of Co Addition on the Phase Structure and Magnetic Properties of Fe-Si-Al Alloys

Unveiling the Precipitation Behavior and Mechanical Properties in G-phase Strengthened CrFe2Ni2Ti0.2Six Multi-Principal Element Alloys

Multi-component Phase-Field Simulation of Microstructural Evolution and Elemental Distribution in Fe–Cu–Mn–Ni–Al Alloy

Design Multicomponent Eutectic Alloys in the Co–Cr–Fe–Ni–Nb System Using Simple Mixing Method

The Alloying Strategy to Tailor the Mechanical Properties of θ-Al13Fe4 Phase in Al-Mg-Fe Alloy by First-Principles Calculations

Insight into the microstructure and micromechanical behavior and mechanism of the constitutional phase of FeNiCrAl 0.63 multi-principal element alloy

Exploring the Relationship between the Structural Characteristics and Mechanical Behavior of Multicomponent Fe-Containing Phases: Experimental Studies and First-Principles Calculations

Effect of Fe content on microstructures and mechanical properties of eutectic Co-Cr-Fe-Ni-Hf multi-principal element alloys

Phase transformation - induced strengthening of an additively manufactured multi- principal element CrMnFeCoNi alloy

Phase selection of BCC/B2 phases for the improvement of tensile behaviors in FeNiCrAl medium entropy alloy

Multiscale-phase-driven strength-ductility synergy in Fe3Cr2CoNiAlx high entropy alloys

Effects of Fe on microstructure and mechanical properties of CoCrNiFeAl multi-principle elements alloys

Alloying behavior of W and Mo in the as-cast dual-phase FeNiCrAl multi-component alloys

Composition and phase structure dependence of magnetic properties for Co2FeCr0.5Alx (x=0.9, 1.2) multi principal component alloys

Formation of hypoeutectic structure and strengthening mechanism of Co4Cr1.5Fe1.5Ni5 high entropy alloy alloyed by Al

Study on Microstructure and Mechanical Properties of CrCuFeNiV Multi Principal Element Alloy

Damping capacity and mechanical properties of Fe3Cr2NiCuAl medium entropy alloys by tuning phase constituents

Controlled Valence Electron Concentration Approach to Tailor the Microstructure and Phase Stability of an Entropy-Enhanced AlCoCrFeNi Alloy

Design and microstructural development of a new eutectic Fe-Co-Ni-B multi-principal element alloy system

Tunability of the Mechanical Properties of (Fe50mn27ni10cr13)100-Mo High-Entropy Alloys Via Secondary Phase Control