Abstract:The laser cladding of the T15 high-speed steel (HSS) was accomplished and its typical microstructure was determined. The microstructure characterization of the clad layer showed three phases of microstructure, planar, cellular and equiaxed growth zones. Electron probe micro-analyzer (EPMA) showed high content in alloying elements at the cellular and equiaxed zones that contained V, C, Cr and W. Further, the analysis at the inter-granular zone presented the highest concentration in elements such as Mo, Cr and W. This showed the presence of carbides which were identified as MCI and M6C at the cellular zone, and M7C3 and M23C6 at the equiaxed and inter-granular zones. The precipitation characterization along the line starting from the substrate and passing through the clad layer identified the austenite matrix and revealed the fluctuation in the alloying elements content, where its amplitude and count increased while passing through the planar zone and hitting the equiaxed zone. Equilibrium phase diagram thermodynamic calculation proved the presence of MCI, M6C and M23C6 which precipitated respectively as the solidification proceeded. The M6C carbide was rich in Fe and W with the presence of V and Cr. MCI carbide had high content of C and V also with dissolved content of W and Cr. Finally, M23C6 carbide contained high amounts of W, Cr and Mo. Scheil–Gulliver simulation model showed the presence of M6C and MCI similar to the equilibrium phase diagram results, additionally, two carbides were revealed and identified as M7C3 and MCII carbides. The M23C6 was absent from the Scheil–Gulliver model. This is due to the assumption that in the Scheil–Gulliver model, the solid stage has no diffusion, and the M23C6 was proved to precipitate in later stages of solidification as shown in the equilibrium phase diagram results. Finally, transmission electron microscopy (TEM) and x-ray diffraction (XRD) showcased the presence of the carbides predicted from the equilibrium phase diagram.

On Intertrack Fluctuation of Hardness and Carbides in T15 Steel Laser Cladding Using Thermodynamic Calculation

Thermodynamic Calculation and Characterization of Carbide Precipitation in Laser-Deposited Material for High-Speed Steel Alloy

The Improvement of the Wear Resistance of T15 Laser Clad Coating by the Uniformity of Microstructure

Microstructure evolution and wear resistance of laser cladded 316L stainless steel reinforced with in-situ VC-Cr7C3

Influence of Heat Treatment on Microstructure and Mechanical Properties of Laser Cladding Coatings

Experimental Study on the Wear Properties of 42CrMo Steel with Different Microstructures and T15 Laser Cladding

Thermal Stability of Laser-Clad Tool Steel with Fine Tungsten Carbide Particle Addition

Study on microstructure and properties of laser-clad Fe-based (Ti, V)C composite coatings

Effect of the Laser Cladding Parameters on Microstructure and Elevated Temperature Wear of FeCrNiTiZr Coatings

Study on the friction and wear performance of laser cladding WC-TiC/Ni60 coating on the working face of shield bobbing cutter

Temperature Field Simulation and Experimental Confirmation of Laser Cladding High-Entropy Alloy Coating on Cr12MoV

Multicomponent Multiphase Modeling of Dissimilar Laser Cladding Process with High-Speed Steel on Medium Carbon Steel

Effect of Cr on Wear Resistance and Mechanism of Preset-Powder Laser Cladding T15 Alloy Steel Coating

Effect of cladding speed on the microstructure and hardness of high-hardness B-bearing Cr17Ni2 coating

Effect of Cr on Microstructure and Properties of WVTaTiCrx Refractory High-Entropy Alloy Laser Cladding

Investigating microstructural and tribological properties of WTaMoHfNi high-entropy refractory alloy applied to GTD-111 superalloy by ultrasonic-assisted laser cladding

Preparation and the Mechanical and Tribological Properties of Laser Cladding Coating

Effect of Heat Treatment on Microstructure and Tribocorrosion Performance of Laser Cladding Ni-65 WC Coating

Computational and Experimental Investigation of Micro-Hardness and Wear Resistance of Ni-Based Alloy and TiC Composite Coating Obtained by Laser Cladding

Effect of Deep Cryogenic Treatment on Microstructure and Wear Resistance of LC3530 Fe-Based Laser Cladding Coating

Microstructure Characteristics and Elevated-Temperature Wear Mechanism of FeCoCrNiAl High-Entropy Alloy Prepared by Laser Cladding