Abstract:In recent years, the popularity of high-power equipment such as electric vehicles demands a higher the energy density, higher the power density, and low cost in lithium-ion batteries (LIBs). The capacity of LIBs is typically limited by the cathode. For example, in LIBs based on LiCoO 2 //graphite system, which have achieved great success in commercialization, the reversible capacity of LiCoO 2 (~137 mAh g -1 ) is lower than that of graphite (~370 mAh g -1 ) [1]. Hence, it is necessary to improve the capacity of the cathode in order to improve the performance of LIBs. Among the cathode materials, Vanadium pentoxide (V 2 O 5 ) is considered as one of the ideal next-generation electrode materials due to its high theoretical capacities (294 mAh g -1 ), high energy densities, good safety and low cost [2]. Nevertheless, its cycle performance and poor rate-capability caused by severe structural changes during the repeated lithiation/de-lithiation, slow diffusion of lithium ion (Li + ), and low electrical conductivity hinders its commercialization [2]. Various attempts to fabricate the nanostructured V 2 O 5 such as nanorods, nanobelts, nanosheet, and hollow spheres have been pursued to remedy the issues. The nanostructures are used to overcome their kinetic limitation by reduction of Li + ion diffusion distance and increase in the electrode/electrolyte contact area. In nanostructures, however, structural collapse and particles agglomeration could emerge during Li + ion penetration procedure [3]. In particular, many studies have focused on the 1D nanostructured V 2 O 5 in length along [010], the fastest growth direction of V 2 O 5 , because of its simplicity in synthesis [4]. However, 1D-nanostructured V 2 O 5 has long Li + ion diffusion distance along [010] direction, which is corresponding to the energy preferred Li + ion diffusion path [5]. 1D diffusion along the short [010] direction in V 2 O 5 can be the fast Li + ion diffusion path for cathode in LIBs. Therefore, to design an optimal structure for V 2 O 5 as cathode materials, the following conditions should be satisfied: i) structures consisted of primary nanostructured units to prevent agglomeration. ii) a short [010] length with high percentage of exposed (010) facets to shorten a Li + ion diffusion path and facilitate the Li + ion intercalation reactions. In this context, we fabricated nanoplates–stacked V 2 O 5 (Li-treated VO) through Li-treatment method in hydrothermal synthesis followed by heat treatment. Li + ions from lithium nitrate (LiNO 3 ), which is added to precursor solution, can inhibit the completely phase transition from xerogel to crystal during hydrothermal process, leading to formation of xerogel/crystal composite. During following heat treatment process, the cleavage and oriented attachment mechanism are accompanied, evolving nanoplates–stacked V 2 O 5 with short [010] length and highly exposed (010) facets (Figure 1). The Li-treated VO electrodes could facilitate the fast and efficient transportation of Li + ion into the [010] channel. In particular, the Li-treated VO electrodes can achieve a reversible capacity of 252 mAh g -1 at 50 mA g -1 in the voltage range of 2.05–4.0 V (vs. Li/Li + ) (Figure 2). Notably, the Li-treated VO electrodes also exhibit a higher rate performance (140 mAh g -1 at 1 A g -1 (Figure 2)) and cycling capability (79 % capacity retention after 100 cycles (Figure 3)) compared to untreated V 2 O 5 nanobelt (VO) electrodes. In addtion, the reversible lithium intercalation reaction and structure stability of Li-treated VO are confirmed by further analyses. Figure 1

High Performance Pillared Vanadium Oxide Cathode for Lithium Ion Batteries

Layered Structure Regulation for Zinc‐Ion Batteries: Rate Capability and Cyclability Enhancement by Rotatable Pillars

Pillar Effect On Cyclability Enhancement For Aqueous Lithium Ion Batteries: A New Material Of Beta-Vanadium Bronze M0.33v2o5 (M = Ag, Na) Nanowires

Artificial Cathode-Electrolyte Interphase towards High-Performance Lithium-Ion Batteries: A Case Study of β-AgVO3

Cations‐Pillared and Polyaniline‐Encapsulated Vanadate Cathode for High‐Performance Aqueous Zinc‐Ion Batteries

Nanoplates-Stacked Vanadium Oxide Cathode Employing Higher Kinetics and Stability in a Lithium-Ion Battery

An elaborate insight of lithiation behavior of V2O5 anode

Novel Polygonal Vanadium Oxide Nanoscrolls as Stable Cathode for Lithium Storage

Towards a Stable Layered Vanadium Oxide Cathode for High-Capacity Calcium Batteries

High-Surface Vanadium Oxides with Large Capacities for Lithium-Ion Batteries: from Hydrated Aerogel to Nanocrystalline Vo2(B), V6o13 and V2o5

Bilayered Vanadium Oxides Pillared by Strontium Ions and Water Molecules as Stable Cathodes for Rechargeable Zn-Metal Batteries

Lithium vanadium oxide (Li1.1V3O8) thick porous electrodes with high rate capacity: utilization and evolution upon extended cycling elucidated via operando energy dispersive X-ray diffraction and continuum simulation

High‐Rate Performance and Ultralong Cycle Life Enabled by Hybrid Organic–Inorganic Vanadyl Ethylene Glycolate for Lithium‐Ion Batteries

Metastable Amorphous Chromium-Vanadium Oxide Nanoparticles with Superior Performance As a New Lithium Battery Cathode

Carbon Nitride Pillared Vanadate Via Chemical Pre-Intercalation Towards High-Performance Aqueous Zinc-Ion Batteries

Amorphous Vanadium Oxide Nanosheets with Alterable Polyhedron Configuration for Fast-Charging Lithium-Ion Batteries.

Organic pillars pre-intercalated V4+-V2O5·3H2O nanocomposites with enlarged interlayer and mixed valence for aqueous Zn-ion storage

Amorphous Vanadium Oxide Nanosheets with Alterable Polyhedron Configuration for FastвАРCharging LithiumвАРIon Batteries

Defect Engineering of Vanadium Pentoxide for Efficient Lithium-Ion Storage

Al/Mn co-doping endows V2O5•4VO2 cathode with enhanced lithium storage performance

Vanadium oxide cathode with synergistic engineering of calcium-ion intercalation and polyaniline coating for high performance zinc-ion batteries