Abstract:Diesel particulate filters (DPFs) are well assessed aftertreatment devices, equipping almost every modern diesel engine on the market to comply with today’s stringent emission standards. However, an accurate estimation of soot loading, which is instrumental to ensuring optimal performance of the whole engine-after-treatment assembly, is still a major challenge. In fact, several highly coupled physical-chemical phenomena occur at the same time, and a vast number of engine and exhaust dependent parameters make this task even more daunting. This challenge may be solved with models characterized by different degrees of detail (0-D to 3-D) depending on the specific application. However, the use of real-time, but accurate enough models, may be the primary hurdle that has to be overcome when confronted with advanced exhaust emissions control challenges, such as the integration of the DPF with the engine or other critical aftertreatment components (selective catalytic reduction or other NOx control components), or to properly develop model-based OBD sensors. This paper aims at addressing real time DPF modeling issues with special regard to key parameter settings, by using the 1-D code called ExhAUST (exhaust aftertreatment unified simulation tool), which was jointly developed by the University of Rome Tor Vergata and West Virginia University. ExhAUST is characterized by a novel and unique full analytical treatment of the wall that allows a highly detailed representation of the soot loading evolution inside the DPF porous matrix. Numerical results are compared with experimental data gathered at West Virginia University engine laboratory using a MY2004 Mack®MP7-355E, an 11 liter, 6-cylinder, inline heavy-duty diesel engine coupled to a Johnson Matthey CCRT diesel oxidation catalyst + CDPF, catalyzed DPF exhaust aftertreatment system. To that aim, the engine test bench was equipped with a DPF weighing system to track soot loading over a specifically developed engine operating procedure. Results indicate that the model is accurate enough to capture soot loading and back pressure histories with regard to different steady state engine operating points, without a need for any tuning procedure of the key parameters. Thus, the use of ExhAUST for application to advanced after-treatment control appears to be a promising tool at this stage.

Multi-objective optimization of performance characteristic of diesel particulate filter for a diesel engine by RSM-MOPSO during soot loading

Multi-objective Impact Mechanism on the Performance Characteristic for a Diesel Particulate Filter by RF-NSGA III-TOPSIS During Soot Loading

Sensitivity Analysis of Diesel Particulate Filters to Geometric Parameters During Soot Loading and Its Multi-Objective Optimization

Multidisciplinary Design Optimization of the Diesel Particulate Filter in the Composite Regeneration Process

Comparison of the Use of Real Diesel Soot and Soot Surrogate in the Performance Analysis of Diesel Particulate Filters

Multiobjective Optimization of Diesel Particulate Filter Regeneration Conditions Based on Machine Learning Combined with Intelligent Algorithms

Methodology of diesel particulate filter testing on test bed for non-road engine application

Effects of Structural Optimization Design of Gasoline Particulate Filter on Soot Emission and Performance of GDI Engine

The state-of-the-art of soot load estimation in diesel particulate filters: A review

Multi-Optimization of Injection Parameters Affecting Emissions in a Diesel Engine Fueled with Fischer–Tropsch Fuel Based on NSGA-II

The Application of Two Closely Coupled DPFs as the After-treatment System

Multi-objective Optimization of Composite Regeneration Performance of a CeO2-based Catalyzed Diesel Particulate Filter

Multi-objective Optimization of Emission Parameters of a Diesel Engine Using Oxygenated Fuel and Pilot Injection Strategy Based on RSM-NSGA III

Lumped model for evaluating dynamic filtration and pressure drop behaviour in diesel particulate filters

Optimization of Flow Field Uniformity of Compact System for Diesel Engine

Soot Modeling for Advanced Control of Diesel Engine Aftertreatment

Impact of multi-injection strategies on morphology, nanostructure and oxidation reactivity of diesel soot particles

Numerical simulation of diesel particulate filter flow characteristics optimization: From the perspective of pore structure parameters and inlet velocity

Modeling of Soot Fragmentation That Proceeds in a Catalyzed Diesel Particulate Filter of a Diesel Engine

A review of regeneration mechanism and methods for reducing soot emissions from diesel particulate filter in diesel engine

Effect of DMDF on the PM Emission from a Turbo-Charged Diesel Engine with DDOC and DPOC