Investigation and Evaluation of Life Cycle Assessment of Printed Electronics and Its Environmental Impacts Analysis

Rajeev Kanth,Qiansu Wan,Pasi Liljeberg,Aulis Tuominen,Li‐Rong Zheng,Hannu Tenhunen

2010-01-01

Abstract:This paper presents cradle to gate life cycle assessment of printed electronics resources. In this work an attempt has been made to investigate and evaluate the life cycle assessment and the enviro ...

What problem does this paper attempt to address?

Life cycle assessment of printed antenna: Comparative analysis and environmental impacts evaluation

rajeev kumar kanth,qiansu wan,harish kumar,pasi liljeberg,lirong zheng,hannu tenhunen

DOI: https://doi.org/10.1109/ISSST.2011.5936899

2011-01-01

Abstract:This paper presents cradle to grave life cycle assessment of printed electronics resources. In this work, an attempt has been made to investigate and evaluate the life cycle assessment and environmental impacts of printed electronics resources such as polymer substrate-printed RFID antenna. Life cycle inventory analysis for these resources has been carried out to quantify total systems' inputs and outputs that are relevant to the environmental impacts especially emissions to air, fresh water, industrial soil and sea water.
Evaluating sustainability, environment assessment and toxic emissions in life cycle stages of printed antenna

rajeev kumar kanth,qiansu wan,harish kumar,pasi liljeberg,qiang chen,lirong zheng,hannu tenhunen

DOI: https://doi.org/10.1016/j.proeng.2012.01.891

2012-01-01

Procedia Engineering

Abstract:In this work cradle to grave life cycle assessment of printed electronics resources have been presented. An attempt has been made to investigate and evaluate the life cycle assessment and environmental impacts of printed electronics resources such as polymer substrate-printed RFID antenna. Life cycle inventory analysis for these resources has been carried out to quantify total systems’ inputs and outputs that are relevant to the environmental impacts especially emissions to air, fresh water, industrial soil and sea water. The results show that printed electronics materials are considerably more environment friendly than materials needed for PCB electronics. We have obtained the mass of emissions in each life cycle stages which verify that technology wise printed antenna causes less harmful and hazardous impacts to the environment.
Evaluating Sustainability, Environmental Assessment and Toxic Emissions During Manufacturing Process of RFID Based Systems

Rajeev Kumar Kanth,Pasi Liljeberg,Hannu Tenhunen,Qiansu Wan,Yasar Amin,Botao Shao,Qiang Chen,Li-Rong Zheng,Harish Kumar

DOI: https://doi.org/10.1109/dasc.2011.175

2011-01-01

Abstract:The present state of the art research in the direction of embedded systems demonstrate that analysis of life-cycle, sustainability and environmental assessment have not been a core focus for researchers. To maximize a researcher's contribution in formulating environmentally friendly products, devising green manufacturing processes and services, there is a strong need to enhance life-cycle awareness and sustainability understandings among embedded systems researchers, so that the next generation of engineers will be able to realize the goal of a sustainable life-cycle. In this work an attempt has been made to investigate and evaluate the life-cycle management and environmental assessment in fabricating processes of the RFID based systems. We have chosen a general life cycle assessment approach which involves the collection and evaluation of quantitative data on the inputs and outputs of materials and energy associated with the RFID based systems. Based on the developed generic models, we have obtained the results in terms of environmental emissions for a production of paper substrate printed RFID antennas. We also make an attempt to raise several sustainability issues and quantify the toxic emissions during the manufacturing process.
Life Cycle Assessment of Paper Based Printed Interconnections for ECG Monitoring

Qiansu Wan,Zhuo Zou,Lirong Zheng

DOI: https://doi.org/10.24018/ejeng.2017.2.6.382

2017-01-01

European Journal of Engineering and Technology Research

Abstract:This paper presents quantitative environment impact evaluation and assessment of inkjet printed flexible cable on soft substrates for Electrocardiography (ECG) monitoring. The studied printed ECG cable is fabricated by inkjet printing of nanoparticles wire on paper substrate which enables wireless transmission of ECG signals between bio-electric electrodes and central medical device. In order to facilitate the inventory analysis, the environmental impacts evaluation of inkjet printing technology has been carried out by comparing with traditional ECG cables. With the life cycle inventory modelling by using GaBi software, the life cycle assessment (LCA) was conducted to qualify the input and output of raw material resources, energy resources used in manufacturing phases and the impacts to environment.
Evaluating the Environmental Sustainability of Electronic Products: A Case Study of Life Cycle Assessment In Coimbatore Region

Krithiga Palanisamy,Sarathi Thasan,Saru Latha,Vasee Haran,S. Natarajan

DOI: https://doi.org/10.1051/matecconf/202338401006

2023-10-28

MATEC Web of Conferences

Abstract:Authors: S. Natarajan, Krithiga Palanisamy, Sarathi Thasan, Saru Latha and Vasee Haran. MATEC Web of Conferences Vol. 384 , page 01006 Published online: 27/10/2023 Keywords: E-waste ; Life Cycle Assessment ; Life Cycle GHG ; Impact categories ; open LCA.
Sustainable Production Insight Through LCA and LCC Analysis of Injection Overmolded Structural Electronics Manufactured through Roll-to-Roll Processes

Minna Räikkönen,Laura Sokka,Lotta Hepo-Oja,Sirpa Nordman,Thomas M Kraft

DOI: https://doi.org/10.1002/gch2.202300015

2023-10-25

Abstract:Printed electronics (PE) have provided new material and application opportunities for devices and systems as well as new manufacturing routes that all need to be considered for commercialization. This paper introduces a case study with universally relevant manufacturing processes and applications in the PE area, focusing on the Life Cycle Assessment (LCA) and Life Cycle Costing (LCC) of the Personal Activity Monitor (PAM) device. In the study, the PAM device's most important costs and environmental impacts during the prototype pilot production and device use phases are identified and assessed. Additionally, the potential environmental impacts of post-consumption scenarios are considered. The LCA results indicate that the roll-to-roll (R2R) assembly of electronics and the R2R injection over-molding are generally the most prominent production process steps affecting the results. From the LCC perspective, the capitial expenditure (CAPEX) contributor is the R2R assembly pilot line, due to its high investment cost and long operating time compare to other production assets. The traditional electronic components are the major operating expenditures (OPEX), especially the microcontroller units (MCUs) and accelerometers, in contrast to the low impact from the printed electronics. There are several advantages to applying LCA and LCC since they provide explanations of the relationships between cost, environmental, design, and manufacturing characteristics.
Future Paper Based Printed Circuit Boards for Green Electronics: Fabrication and Life Cycle Assessment

Jingping Liu,Cheng Yang,Haoyi Wu,Ziyin Lin,Zhexu Zhang,Ronghe Wang,Baohua Li,Feiyu Kang,Lei Shi,Ching Ping Wong

DOI: https://doi.org/10.1039/c4ee01995d

IF: 32.5

2014-01-01

Energy & Environmental Science

Abstract:Paper-based electronics have been considered as one of the most exciting technologies in the near future due to sustainability, low cost, mechanical flexibility, etc. Even though there have been numerous studies regarding this technology, there is not any available quantitative study on how paper electronics would minimize the impact on the environment. This work aims to give the first detailed analysis regarding this important question. To this end, we for the first time designed and prototyped paper-based multilayer printed circuit boards (P-PCBs), which show comparable functions to the currently available organic printed circuit boards (O-PCBs); yet the P-PCBs adopt a "green" preparation process. A life cycle assessment study was performed to quantify the P-PCBs' environmental impacts, e.g. acidification potential, global warming potential, human toxic potential, ozone layer depletion potential, etc. Our current research reveals that the P-PCBs have about two magnitude lower impact on the environment than O-PCBs based on the results of the life cycle assessment, which suggests that the P-PCB technique is beneficial for the environment at the regional or global production level. The current study gives useful information and sheds light on the future technological directions for various paper based electronics studies.
Steering Innovation toward Sustainable Electrochromic Displays: A Prospective Life Cycle Assessment Study

A. Kamal Kamali,Daye Lee,Romain Futsch,Edis Glogic,Aline Rougier,Guido Sonnemann

DOI: https://doi.org/10.1021/acssuschemeng.3c06079

IF: 8.4

2024-01-16

ACS Sustainable Chemistry & Engineering

Abstract:Printed electrochromic displays (ECDs) have promising applications in visual communications. A cradle-to-gate ex-ante prospective life cycle assessment (LCA) was conducted on six ECD architectures to uncover the environmental implications of material and technological choices. Several materials were considered in ECD fabrication, including silver, carbon, and indium tin oxide (ITO) electrodes, plastic- and paper-based substrates, and two electrolytes. The architectures differed in technology maturity levels, ranging from pilot-scale and lab-scale prototypes to conceptual designs. Regardless of their technological maturity, all architectures were scaled up to emulate impact burdens as if they were produced on an optimized industrial production scale. The analysis of ECD architectures at the early development stage, especially conceptual designs, determines their environmental viability without the need for experimental testing, resulting in significant savings of time and resources. The all-silver architecture was associated with the highest environmental impacts across all endpoint and midpoint indicators, except for the water consumption indicator. On the other hand, the all-carbon architecture exhibited the lowest environmental impacts, followed by the carbon-ITO architecture and all-ITO architecture. Based on the environmental impact results, we could identify ECD architectures that merit further development and those that have limited potential for improvement, thus recommending to cease research and development of ECD architectures employing silver electrodes. The approach employed in this LCA guides scaling-up and predicting the environmental impacts of conceptual ECD architectures. This may benefit LCA practitioners and researchers engaged in ex-ante prospective LCA studies. Furthermore, the findings of this LCA might be applicable to other electronic devices, where silver, ITO, and carbon could be interchangeably used as electrodes.

chemistry, multidisciplinary,engineering, chemical,green & sustainable science & technology
Life cycle assessment study of a Chinese desktop personal computer.

Huabo Duan,Martin Eugster,Roland Hischier,Martin Streicher-Porte,Jinhui Li

DOI: https://doi.org/10.1016/j.scitotenv.2008.10.063

2009-01-01

Abstract:Associated with the tremendous prosperity in world electronic information and telecommunication industry, there continues to be an increasing awareness of the environmental impacts related to the accelerating mass production, electricity use, and waste management of electronic and electric products (e-products). China's importance as both a consumer and supplier of e-products has grown at an unprecedented pace in recent decade. Hence, this paper aims to describe the application of life cycle assessment (LCA) to investigate the environmental performance of Chinese e-products from a global level. A desktop personal computer system has been selected to carry out a detailed and modular LCA which follows the ISO 14040 series. The LCA is constructed by SimaPro software version 7.0 and expressed with the Eco-indicator'99 life cycle impact assessment method. For a sensitivity analysis of the overall LCA results, the so-called CML method is used in order to estimate the influence of the choice of the assessment method on the result. Life cycle inventory information is complied by ecoinvent 1.3 databases, combined with literature and field investigations on the present Chinese situation. The established LCA study shows that that the manufacturing and the use of such devices are of the highest environmental importance. In the manufacturing of such devices, the integrated circuits (ICs) and the Liquid Crystal Display (LCD) are those parts contributing most to the impact. As no other aspects are taken into account during the use phase, the impact is due to the way how the electricity is produced. The final process steps – i.e. the end of life phase – lead to a clear environmental benefit if a formal and modern, up-to-date technical system is assumed, like here in this study.
Application of Life Cycle Assessment on Electronic Waste Management: A Review

Mianqiang Xue,Zhenming Xu

DOI: https://doi.org/10.1007/s00267-016-0812-1

2016-01-01

Environmental Management

Abstract:Electronic waste is a rich source of both valuable materials and toxic substances. Management of electronic waste is one of the biggest challenges of current worldwide concern. As an effective and prevailing environmental management tool, life cycle assessment can evaluate the environmental performance of electronic waste management activities. Quite a few scientific literatures reporting life cycle assessment of electronic waste management with significant outcomes have been recently published. This paper reviewed the trends, characteristics, research gaps, and challenges of these studies providing detailed information for practitioners involved in electronic waste management. The results showed that life cycle assessment studies were most carried out in Europe, followed by Asia and North America. The research subject of the studies mainly includes monitors, waste printed circuit boards, mobile phones, computers, printers, batteries, toys, dishwashers, and light-emitting diodes. CML was the most widely used life cycle impact assessment method in life cycle assessment studies on electronic waste management, followed by EI99. Furthermore, 40% of the reviewed studies combined with other environmental tools, including life cycle cost, material flow analysis, multi-criteria decision analysis, emergy analysis, and hazard assessment which came to more comprehensive conclusions from different aspects. The research gaps and challenges including uneven distribution of life cycle assessment studies, life cycle impact assessment methods selection, comparison of the results, and uncertainty of the life cycle assessment studies were examined. Although life cycle assessment of electronic waste management facing challenges, their results will play more and more important role in electronic waste management practices.
Product life cycle assessment and environmental efficiency assessment

Yuhua Cao,Guozhang Chen,Guoning Qi,Xinjian Gu,Hongguang Peng

DOI: https://doi.org/10.1007/978-3-642-38442-4_146

2013-01-01

Abstract:With growing human demand for a variety of economic, resources and environment exerting a profound human impact on the environment, in order to deal with economic, resource and environment relationship, life cycle assessment (LCA) and environmental efficiency evaluation are widely used. In order to more accurately conduct the environmental assessment of the product, it is needed to rationally utilize life cycle assessment and environmental efficiency evaluation, put accurate environmental load data into effective use of the evaluation of environmental efficiency, in which environmental efficiency indicators and the performance factor index correctly reflects the value of the product enhancement and mitigation of environmental load. © Springer-Verlag Berlin Heidelberg 2013.
The Need for Design-for-Recycling of Paper-Based Printed Electronics – a Prospective Comparison with Printed Circuit Boards

Akshat Sudheshwar,Nadia Malinverno,Roland Hischier,Bernd Nowack,Claudia Som

DOI: https://doi.org/10.2139/ssrn.4208558

2022-01-01

SSRN Electronic Journal

Abstract:The present study compares conventional printed circuit boards (having glass-fibre and epoxy substrates and etched copper circuits) with paper-based printed electronics (offering flexible, bio-based, and biodegradable substrates with circuit design printed using silver-based inks) and assesses the relevance of e-waste recycling to the latter's sustainability. Therefore, a comparative life cycle assessment between these two options has been undertaken and the global warming impacts were calculated.The impact assessment results underscore that printed electronics offer a consistent sustainability advantage over printed circuit boards only through recycling of silver in the former at the end-of-life. Hence, design-for-recycling and recycling as e-waste are crucial to the sustainability of the current generation of printed electronics. Other foreseen waste treatment options for paper-based printed electronics, such as composting, and paper recycling, are likely to limit the sustainability advantage of printed electronics to circuits with small conductive areas.
Life cycle assessment of a new smart label for intelligent packaging

Laura Sokka,Marja Välimäki,Kaisa-Leena Väisänen,Jari Keskinen,Elina Jansson,Matti Mäntysalo,Jyrki Ollila,Tuomas Happonen,Liisa Hakola,Maria Smolander

DOI: https://doi.org/10.1088/2058-8585/ad2279

IF: 3.1

2024-01-26

Flexible and Printed Electronics

Abstract:Within the past years, there has been a growing demand for sustainable, cost-efficient on-line sensing of chemical and physical properties and locations of products. Measuring of products' physical properties, such as temperature and humidity, could improve product safety and efficiency of logistic operations. In the future measurement of temperature of food items could also aid in reducing food wastage. The aim of this study was to calculate the life cycle environment impacts of a temperature logger, hereafter called smart label, primarily targeted for the monitoring of the packed food products. According to the results, the largest normalised impacts of the smart label production are resource use (both use of fossil fuels and use of minerals and metals), eutrophication and particulate matter formation. The main materials causing these impacts were the printed electronics inks and adhesives. In addition, energy used in the production, and plastics used as substrates had large impacts on the results. It should be noted that the present calculations have mainly been made on a laboratory scale. The impacts are likely to get smaller on an industrial scale with more efficient production. In the future, the label could potentially bring environmental benefits through product savings when used in products with high environmental load.

materials science, multidisciplinary
Comparison of life cycle assessment for laminating and glazing processes based on simapro

Qingbin Cui,Fenjuan Shao

DOI: https://doi.org/10.1108/prt-09-2021-0116

2022-01-20

Abstract:Purpose Both glazing and laminating play a certain role in finishing and protecting the surface of printed matter. This study makes a comparative analysis of the two through life cycle assessment (LCA) and theoretically explores the difference between them. Design/methodology/approach In this study, the life cycle of laminating and glazing processes was calculated through using Simapro software, and the results were compared and analyzed. Findings Twelve environmental categories were used to quantitatively analyze the environmental impact of the product. The results showed that the results of the 12 environmental categories involved in the analysis of glazing was less than that of laminating, indicating that the impact of the glazing on the environment was less than that of laminating on the environment. Research limitations/implications In order to simplify the study, we only calculated and analyzed the laminating and glazing. Practical implications Green packaging is the future, 3R1D, reduce, reuse, recycle and degradable. According to the calculation results, corresponding suggestions can be put forward from production, processing, use, waste and other aspects, and make corresponding contributions to the development of green packaging. Originality/value The contribution and impact of each stage to the product life cycle can be studied. In addition, different waste disposal methods have different impacts on the environment, and the higher the recovery ratio, the better the environmental benefits of the product. Recycling should then be promoted as proportionately as possible in practice in order to reduce the environmental impact .

engineering, chemical,materials science, coatings & films,chemistry, applied
A Review on Recyclable Printed Electronics: Fabrication Methods, Inks, Substrates, Applications and Environmental Impacts

Jenny Wiklund,Alp Karakoc,Toni Palko,Huseyin Yigitler,Kalle Ruttik,Riku Jäntti,Jouni Paltakari

DOI: https://doi.org/10.20944/preprints202106.0017.v1

2021-06-01

Abstract:Innovations in industrial automation, information and communication technology (ICT), renewable energy, monitoring and sensing fields have been paving the way for smart devices, which can acquire and convey information to the internet, in every aspect of our lives. Since there is ever-increasing demand for large yet affordable production volumes for such devices, printed electronics has been attracting great attention in both industrial and academic research. In order to understand the potential and future prospects of the printed electronics, the present paper summarizes the basic principles and conventional approaches while providing the recent progresses in the fabrication and material technologies, applications and environmental impacts.
Quantifying the environmental footprint of rigid substrate printed antenna

rajeev kumar kanth,pasi liljeberg,hannu tenhunen,yasar amin,qiang chen,lirong zheng,h d kumar

DOI: https://doi.org/10.1109/TSAsia.2012.6397973

2012-01-01

Abstract:Quantifying environmental footprint is an important task for the embedded system researcher as this study keep them aware of environmental impacts' threat toward green and healthy living of human beings. In this work we have presented a study on analysis of sustainability and environmental impacts assessment in manufacturing process of rigid substrate printed antennas. Life cycle assessment approach has been employed to quantify and asses the environmental footprint. A case study has been carried out for epoxy resin substrate based tip truncated equilateral triangle microstrip antenna. The subtractive printing methodology have been conducted to trace the required antenna pattern. The output parameters have been analyzed in terms of global warming potential, ozone layer depletion potential, human toxicity and acidification potential. Gabi's balance approach has been utilized to analyze the environmental emissions to the air, fresh water, sea water, agricultural and industrial soils. The consumption of resources has also been shortly described in this paper.
Review of life cycle assessment on consumer electronic products: Developments and the way ahead

Karpagam Subramanian,Winco K. C. Yung

DOI: https://doi.org/10.1080/10643389.2016.1245550

IF: 12.6

2016-09-16

Critical Reviews in Environmental Science and Technology

Abstract:Life cycle assessment (LCA) has grown rapidly and is now well established within the electronics industry. The growing number of journal publications, conferences, and special issues is a proof for the same. A number of literature reviews have been published till now in this area focusing on different aspects. This study has identified 134 significant journal articles to conduct a systematic and narrative literature review. This review covers a wide range of product categories and analyzes the usefulness of LCA as a decision-making tool within the electronics industry which has not been explored fully in previous reviews conducted in this area of research. For this purpose, we organized LCA studies into 10 main product categories. A narrative review was employed to summarize the significant findings from the LCA studies. Although the central objective of all the studies was to evaluate the environmental impact created by the product, the focus and methods employed differed. A systematic review was used to categorize the overall frameworks used in the studies. The studies were classified based on their research purpose, types of approach, LCIA methods used, system boundaries involved, data collection methods, and data analysis levels. Within the subcategory of research purpose, three research domains were identified and the studies were classified accordingly. Generally it has been revealed that use phase, end of life, and production phase are the dominant phases in that order. However discrepancies occur owing to functional units, data usage, and assumptions made. All these and more make benchmarking difficult. Finally we identified gaps that merit attention in future research. It is also hoped that this review is a good resource for anyone interested in doing research on LCA of electronic products, helping them identify current research trends, provide suggestions for future research, and stimulate interest in creating new research directions.

environmental sciences
Life Cycle Assessment of Electronic Waste Treatment.

Jinglan Hong,Wenxiao Shi,Yutao Wang,Wei Chen,Xiangzhi Li

DOI: https://doi.org/10.1016/j.wasman.2014.12.022

2015-01-01

Abstract:Life cycle assessment was conducted to estimate the environmental impact of electronic waste (e-waste) treatment. E-waste recycling with an end-life disposal scenario is environmentally beneficial because of the low environmental burden generated from human toxicity, terrestrial ecotoxicity, freshwater ecotoxicity, and marine ecotoxicity categories. Landfill and incineration technologies have a lower and higher environmental burden than the e-waste recycling with an end-life disposal scenario, respectively. The key factors in reducing the overall environmental impact of e-waste recycling are optimizing energy consumption efficiency, reducing wastewater and solid waste effluent, increasing proper e-waste treatment amount, avoiding e-waste disposal to landfill and incineration sites, and clearly defining the duties of all stakeholders (e.g., manufacturers, retailers, recycling companies, and consumers).
Evaluation of life cycle assessment in a paper manufacture by analytical hierarchy process

Mohammad Moosavi,Payam Ghorbannezhad,Majid Azizi,Hamid Zarea Hosseinabadi

DOI: https://doi.org/10.1080/19397038.2021.1982065

2021-09-27

International Journal of Sustainable Engineering

Abstract:Life cycle assessment (LCA) is an attractive approach to implement the waste management system in terms of environmental sustainability. The variety of environmental options has been made an emergence requirement a methodology to choose the best options for decision-makers. This paper aims to generate a comprehensive model to facilitate the life cycle products to develop a cleaner production strategy in paper manufacture. In the first step, the requirement and adopting models are applied to determine the main criteria of LCA. Then, an analytical hierarchy process (AHP) model is designed to assess the LCA qualification of the paper manufacturing process according to the selected criteria. The environmental impact, production process, technical capability, raw material, energy consumption, human resource, manufactured products, and economic are selected as a higher priority after considering the requirement and adopting the decision model. Pair-wise comparative of 52 sub-criteria showed that circulating of water and solid waste reusing from wastewater treatment plant through dissolved air flotation (DAF) and disk filter enables us to have many advantages not only the pollutants removal but also the enhancement of the LCA framework.
A Sensitivity Analysis Approach to Identify Key Environmental Performance Factors

Xi Yu,Aicha Sekhari,Antoine Nongaillard,Abdelaziz Bouras,Suiran Yu

DOI: https://doi.org/10.1155/2014/918795

IF: 1.43

2014-01-01

Mathematical Problems in Engineering

Abstract:Life cycle assessment (LCA) is widely used in design phase to reduce the product’s environmental impacts through the whole product life cycle (PLC) during the last two decades. The traditional LCA is restricted to assessing the environmental impacts of a product and the results cannot reflect the effects of changes within the life cycle. In order to improve the quality of ecodesign, it is a growing need to develop an approach which can reflect the changes between the design parameters and product’s environmental impacts. A sensitivity analysis approach based on LCA and ecodesign is proposed in this paper. The key environmental performance factors which have significant influence on the products’ environmental impacts can be identified by analyzing the relationship between environmental impacts and the design parameters. Users without much environmental knowledge can use this approach to determine which design parameter should be first considered when (re)designing a product. A printed circuit board (PCB) case study is conducted; eight design parameters are chosen to be analyzed by our approach. The result shows that the carbon dioxide emission during the PCB manufacture is highly sensitive to the area of PCB panel.

Investigation and Evaluation of Life Cycle Assessment of Printed Electronics and Its Environmental Impacts Analysis

Life cycle assessment of printed antenna: Comparative analysis and environmental impacts evaluation

Evaluating sustainability, environment assessment and toxic emissions in life cycle stages of printed antenna

Evaluating Sustainability, Environmental Assessment and Toxic Emissions During Manufacturing Process of RFID Based Systems

Life Cycle Assessment of Paper Based Printed Interconnections for ECG Monitoring

Evaluating the Environmental Sustainability of Electronic Products: A Case Study of Life Cycle Assessment In Coimbatore Region

Sustainable Production Insight Through LCA and LCC Analysis of Injection Overmolded Structural Electronics Manufactured through Roll-to-Roll Processes

Future Paper Based Printed Circuit Boards for Green Electronics: Fabrication and Life Cycle Assessment

Steering Innovation toward Sustainable Electrochromic Displays: A Prospective Life Cycle Assessment Study

Life cycle assessment study of a Chinese desktop personal computer.

Application of Life Cycle Assessment on Electronic Waste Management: A Review

Product life cycle assessment and environmental efficiency assessment

The Need for Design-for-Recycling of Paper-Based Printed Electronics – a Prospective Comparison with Printed Circuit Boards

Life cycle assessment of a new smart label for intelligent packaging

Comparison of life cycle assessment for laminating and glazing processes based on simapro

A Review on Recyclable Printed Electronics: Fabrication Methods, Inks, Substrates, Applications and Environmental Impacts

Quantifying the environmental footprint of rigid substrate printed antenna

Review of life cycle assessment on consumer electronic products: Developments and the way ahead

Life Cycle Assessment of Electronic Waste Treatment.

Evaluation of life cycle assessment in a paper manufacture by analytical hierarchy process

A Sensitivity Analysis Approach to Identify Key Environmental Performance Factors