Validation of Time-Resolved Microwave Conductivity (TRMC) As a Screening Tool for All-Polymer Solar Cells

Supriya Pillai,Neil O. Anderson,Chao Wang,Jonas M. Bjuggren,Martyn Jevric,Mats R. Andersson,Nikos Kopidakis,Chris McNeill

DOI: https://doi.org/10.26180/5d106857726e5

2019-01-01

Abstract:This report describes research validating time-resolved microwave conductivity as a screening tool to discover new, efficient all-polymer solar cell systems.

What problem does this paper attempt to address?

Non-resonant phase sensitive approach for time resolved microwave conductivity in photoactive thin films

Jasleen K. Bindra,Pragya R. Shrestha,Sebastian Engmann,Chad D. Cruz,David J. Gundlach,Emily G. Bittle,Jason P. Campbell

DOI: https://doi.org/10.1016/j.mtadv.2024.100471

IF: 9.918

2024-02-09

Materials Today Advances

Abstract:Time-resolved microwave conductivity (TRMC) is a contactless technique utilized for the investigation of carrier density, transport properties, trapping phenomena, and recombination parameters in charge transport materials. Traditional TRMC methods rely on resonant cavities or resonators, which impose limitations on the frequency range and accuracy of measurements. In this study, we introduce an innovative approach that employs a non-resonant coplanar transmission line and a microwave interferometric detection scheme to investigate the phase-dependent complex microwave conductivity. Additionally, we demonstrate unique calibration techniques for determining the absolute complex microwave conductivity by combining transient photoconductivity (TPC) and electron spin resonance (ESR) as complementary methods. By utilizing a phase-sensitive microwave interferometer, our detection scheme significantly enhances measurement sensitivity and eliminates the need for a resonant cavity. This broadband detection system enables direct measurement of phase-dependent changes in film conductivity (Δσ). Moreover, it allows us to measure subtle variations in sample photoconductivity upon optical excitation and accommodates greatly restricted volumes (∼nL) consistent with typical device sizes. Here we demonstrate the utility of this technique on a series of poly(3-hexylthiophene) (P3HT) and the electron acceptor [6,6]-phenylC61-butyric acid methyl ester (PCBM) thin films with varying concentrations of PCBM and film thickness.

materials science, multidisciplinary
Matrix Organization and Merit Factor Evaluation as a Method to Address the Challenge of Finding a Polymer Material for Roll Coated Polymer Solar Cells

Eva Bundgaard,Francesco Livi,Ole Hagemann,Jon E. Carlé,Martin Helgesen,Ilona M. Heckler,Natalia K. Zawacka,Dechan Angmo,Thue T. Larsen‐Olsen,Gisele A. dos Reis Benatto,Bérenger Roth,Morten V. Madsen,Mats R. Andersson,Mikkel Jørgensen,Roar R. Søndergaard,Frederik C. Krebs,Thue T. Larsen-Olsen

DOI: https://doi.org/10.1002/aenm.201402186

IF: 27.8

2015-02-19

Advanced Energy Materials

Abstract:The results presented demonstrate how the screening of 104 light‐absorbing low band gap polymers for suitability in roll coated polymer solar cells can be accomplished through rational synthesis according to a matrix where 8 donor and 13 acceptor units are organized in rows and columns. Synthesis of all the polymers corresponding to all combinations of donor and acceptor units is followed by characterization of all the materials with respect to molecular weight, electrochemical energy levels, band gaps, photochemical stability, carrier mobility, and photovoltaic parameters. The photovoltaic evaluation is carried out with specific reference to scalable manufacture, which includes large area (1 cm2), stable inverted device architecture, an indium‐tin‐oxide‐free fully printed flexible front electrode with ZnO/PEDOT:PSS (poly(3,4‐ethylenedioxythiophene):polystyrene sulfonate), and a printed silver comb back electrode structure. The matrix organization enables fast identification of active layer materials according to a weighted merit factor that includes more than simply the power conversion efficiency and is used as a method to identify the lead candidates. Based on several characteristics included in the merit factor, it is found that 13 out of the 104 synthesized polymers outperformed poly(3‐hexylthiophene) under the chosen processing conditions and thus can be suitable for further development. A screening of 104 polymer materials for use in roll‐coated polymer solar cells is reported. By synthesis, characterization, and photovoltaic performances of 104 polymers it is demonstrated that finding suitable materials for large scale roll‐to‐roll fabricated polymer solar cells is an enormous challenge. The study shows that 13 polymers out of 104 outperform poly(3‐hexylthiophene) (P3HT) and are suitable for further development.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,energy & fuels
Detailed investigation of TLM contact resistance measurements on crystalline silicon solar cells

Siyu Guo,Geoffrey Gregory,Andrew M. Gabor,Winston V. Schoenfeld,Kristopher O. Davis

DOI: https://doi.org/10.1016/j.solener.2017.05.015

IF: 7.188

2017-07-01

Solar Energy

Abstract:The transmission line method (TLM) is often used in characterizing the contact resistance of c-Si solar cells by cutting cells into strips parallel to the busbars. When applying this method to industrial solar cells, we found various problems that have not been sufficiently explained in prior work. In this paper, we investigate different factors that influence the accuracy of this measurement, using both simulation and experimental methods. The following factors are shown to influence the extracted contact resistivity and are investigated in this work: (1) strip width; (2) edge shunting; (3) current flow through the intermediate unprobed fingers; (4) non-uniform contact resistance; and (5) non-uniform sheet resistance. In cases where the contact resistivity values determined from the TLM measurements and simulations were found to be inaccurate, we introduce correction procedures and measurement guidelines that reduce error. For example, when strip width is a factor, the measurement error of a 30mm sample is reduced from 95.5% to 4.5% using a correction procedure validated by simulation. Furthermore, the methods are also shown to be very effective when applied to industrial solar cells. TLM measurements have an important role to play in both cell R&D and factory quality control, and this work can serve as a guide towards more accurate contact resistivity measurements.

energy & fuels
Real-time monitoring polymerization degree of organic photovoltaic materials toward no batch-to-batch variations in device performance

Lin-Yong Xu,Wei Wang,Xinrong Yang,Shanshan Wang,Yiming Shao,Mingxia Chen,Rui Sun,Jie Min

DOI: https://doi.org/10.1038/s41467-024-45510-w

IF: 16.6

2024-02-10

Nature Communications

Abstract:Abstract Polymerization degree plays a vital role in material properties. Previous methodologies of molecular weight control generally cannot suppress or alleviate batch-to-batch variations in device performance, especially in polymer solar cells. Herein, we develop an in-situ photoluminescence system in tandem with a set of analysis and processing procedures to track and estimate the polymerization degree of organic photovoltaic materials. To support the development of this protocol, we introduce polymer acceptor PYT constructed by near-infrared Y-series small molecule acceptors via Stille polymerization, and shed light on the correlations between molecular weight, spectral parameters, and device efficiencies that enable the design of the optical setup and confirm its feasibility. The universality is verified in PYT derivatives with stereoregularity and fluoro-substitution as well as benzo[1,2-b:4,5-b’]dithiophene-based polymers. Overall, our result provides a tool to tailor suitable conjugated oligomers applied to polymer solar cells and other organic electronics for industrial scalability and desired cost reduction.

multidisciplinary sciences
Machine Learning for Ultra High Throughput Screening of Organic Solar Cells: Solving the Needle in the Haystack Problem

Markus Hußner,Richard Adam Pacalaj,Gerhard Olaf Müller‐Dieckert,Chao Liu,Zhisheng Zhou,Nahdia Majeed,Steve Greedy,Ivan Ramirez,Ning Li,Seyed Mehrdad Hosseini,Christian Uhrich,Christoph Josef Brabec,James Robert Durrant,Carsten Deibel,Roderick Charles Ian MacKenzie

DOI: https://doi.org/10.1002/aenm.202303000

IF: 27.8

2023-12-04

Advanced Energy Materials

Abstract:A machine learning method is demonstrated that can extract mobility (mu) and recombination time constants (tau) directly from light JV curves, this removes the need for transient and frequency domain measurements. Once trained the model can be applied in a matter of seconds, allowing historical data sets to be efficiently mined to reveal the underlying causes of device performance. Finally, measurements from solar cells are discussed in terms of information entropy. Over the last two decades the organic solar cell community has synthesized tens of thousands of novel polymers and small molecules in the search for an optimum light harvesting material. These materials are often crudely evaluated simply by measuring the current–voltage (JV) curves in the light to obtain power conversion efficiencies (PCEs). Materials with low PCEs are quickly disregarded in the search for higher efficiencies. More complex measurements such as frequency/time domain characterization that could explain why the material performed as it is often not performed as they are too time consuming/complex. This limited feedback forced the field to advance using a more or less random walk of material development and has significantly slowed progress. Herein, a simple technique based on machine learning that can quickly and accurately extract recombination time constants and charge carrier mobilities as a function of light intensity simply from light/dark JV curves alone. This technique reduces the time to fully analyze a working cell from weeks to seconds and opens up the possibility of not only fully characterizing new devices as they are fabricated, but also data mining historical data sets for promising materials the community has overlooked.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,energy & fuels
Experimental Validation of Optimized Solar Cell Capacitance Simulation for Rheology‐Modulated Carbon‐Based Hole Transport Layer‐Free Perovskite Solar Cell

Sreeram Valsalakumar,Shubhranshu Bhandari,Tapas K. Mallick,Justin Hinshelwood,Senthilarasu Sundaram

DOI: https://doi.org/10.1002/aesr.202300244

2024-02-29

Advanced Energy and Sustainability Research

Abstract:The rheology of materials influences the nature of thin films for photovoltaic application. This report demonstrates the performance of rheology‐modulated hole transport layer‐free carbon counter electrode perovskite devices using SCAPS‐1D theoretical analysis. Alongside this, the simulated results are validated utilizing the experimental pathway of real‐world device fabrication, illustrating the parallel importance of theoretical and experimental research. The hole transport layer (HTL)‐free carbon‐based perovskite solar cell (C‐PSC) has attracted the attention of researchers due to its ease of fabrication and reduced costs in the manufacturing process. The rheological and physical characteristics of the solutions influence the layer quality of different device fabrication methods. Herein, the HTL‐free structure of C‐PSC through solar cell capacitance simulator (SCAPS) simulations is analyzed and validated with experimental results using rheology‐varied mesoporous‐TiO2 (m‐TiO2) paste. Regarding the m‐TiO2 rheology, two different samples (Type 1 and Type 2) are used, and six different configurations by thickness variation are analyzed utilizing SCAPS simulations. For Type 1 and Type 2, the best configurations exhibit theoretical efficiencies of 16.40% and 16.81%, respectively, without the influence of the resistance factor. After replicating similar designs in experiments, the efficiencies become 10.12% and 12.20%, respectively. Further, results are investigated by SCAPS simulations incorporating series and shunt resistance values, resulting in efficiencies of 10.56% and 12.59% for Type 1 and Type 2, respectively, which is comparable with actual devices. Finally, the variation of theoretical and experimental results is scrutinized with the help of impedance spectroscopy and external quantum efficiency, demonstrating the significance of this work for commercialization aspects.
Machine learning for ultra high throughput screening of organic solar cells: Solving the needle in the hay stack problem

Markus Hußner,Pacalaj A. Richard,Olaf G. Müller-Dieckert,Chao Liu,Zhisheng Zhou,Nahdia Majeed,Steve Greedy,Ivan Ramirez,Ning Li,Seyed Mehrdad Hosseini,Christian Uhrich,Christoph J. Brabec,James R. Durrant,Carsten Deibel,Roderick C. I. MacKenzie

2023-09-07

Abstract:Over the last two decades the organic solar cell community has synthesised tens of thousands of novel polymers and small molecules in the search for an optimum light harvesting material. These materials were often crudely evaluated simply by measuring the current voltage curves in the light to obtain power conversion efficiencies (PCEs). Materials with low PCEs were quickly disregarded in the search for higher efficiencies. More complex measurements such as frequency/time domain characterisation that could explain why the material performed as it did were often not performed as they were too time consuming/complex. This limited feedback forced the field to advance using a more or less random walk of material development and has significantly slowed progress. Herein, we present a simple technique based on machine learning that can quickly and accurately extract recombination time constants and charge carrier mobilities as a function of light intensity simply from light/dark JV curves alone. This technique reduces the time to fully analyse a working cell from weeks to seconds and opens up the possibility of not only fully characterising new devices as they are fabricated, but also data mining historical data sets for promising materials the community has over looked.

Applied Physics
Advancing Accuracy in Perovskite Tandem Solar Cell Efficiency via Transfer Matrix-Based Realistic Device Simulations

Nikhil Shrivastav,Jaya Madan,Rahul Pandey

DOI: https://doi.org/10.1007/s11664-024-11141-6

IF: 2.1

2024-06-12

Journal of Electronic Materials

Abstract:Numerous researchers have dedicated efforts toward enhancing the efficiency of solar cells, particularly through the utilization of multi-junction or tandem solar cell configurations. However, a common approach employed by many researchers involves the use of the standard absorption formula (SAF) to determine the transmitted spectrum from the top cell to illuminate the bottom cells. The SAF method relies on conventional absorption calculations, neglecting reflection, refraction, and parasitic absorption losses. In this study, the transfer matrix (TRM) method, which accounts for reflection and refraction losses and an interference effect, is reported for the accurate calculation of a filtered spectrum. A comparative analysis between the SAF and TRM approaches reveal that the TRM technique provides a more accurate representation of the transmitted spectrum, particularly when considering reflection, refraction, and parasitic absorption losses. The primary aim of this research is to precisely predict the efficiency of tandem configurations by integrating multiple low-bandgap semiconductor bottom cells (BCs) with a top cell (TC) based on high-bandgap perovskite (PVK). Furthermore, the optimization of current matching is achieved by adjusting the thicknesses of the top absorber layer (TAL) and bottom absorber layer (BAL) based on the obtained filtered spectra. Tandem devices optimized using the TRM approach exhibit superior performance, achieving efficiencies of 28.72% (PVK/c-Si), 27.88% (PVK/CIGS), and 29.99% (PVK/PVK). This comparative investigation underscores the importance of considering reflection and refraction losses in tandem solar cell design and highlights the effectiveness of the TRM technique in enhancing device performance.

engineering, electrical & electronic,materials science, multidisciplinary,physics, applied
Machine learning-based screening of complex molecules for polymer solar cells

Peter Bjørn Jørgensen,Murat Mesta,Suranjan Shil,Juan Maria García Lastra,Karsten Wedel Jacobsen,Kristian Sommer Thygesen,Mikkel N. Schmidt

DOI: https://doi.org/10.1063/1.5023563

IF: 4.304

2018-06-28

The Journal of Chemical Physics

Abstract:Polymer solar cells admit numerous potential advantages including low energy payback time and scalable high-speed manufacturing, but the power conversion efficiency is currently lower than for their inorganic counterparts. In a Phenyl-C_61-Butyric-Acid-Methyl-Ester (PCBM)-based blended polymer solar cell, the optical gap of the polymer and the energetic alignment of the lowest unoccupied molecular orbital (LUMO) of the polymer and the PCBM are crucial for the device efficiency. Searching for new and better materials for polymer solar cells is a computationally costly affair using density functional theory (DFT) calculations. In this work, we propose a screening procedure using a simple string representation for a promising class of donor-acceptor polymers in conjunction with a grammar variational autoencoder. The model is trained on a dataset of 3989 monomers obtained from DFT calculations and is able to predict LUMO and the lowest optical transition energy for unseen molecules with mean absolute errors of 43 and 74 meV, respectively, without knowledge of the atomic positions. We demonstrate the merit of the model for generating new molecules with the desired LUMO and optical gap energies which increases the chance of finding suitable polymers by more than a factor of five in comparison to the randomised search used in gathering the training set.
A Round Robin Study of Polymer Solar Cells and Small Modules Across China

Thue T. Larsen-Olsen,Suren A. Gevorgyan,Roar R. Sondergaard,Markus Hosel,Zhouwei Gu,Hongzheng Chen,Yao Liu,Pei Cheng,Yan Jing,Hui Li,Jizheng Wang,Jianhui Hou,Yongfang Li,Xiaowei Zhan,Jiang Wu,Jian Liu,Zhiyuan Xie,Xiaoyan Du,Liming Ding,Chen Xie,Rong Zeng,Yiwang Chen,Wenwu Li,Ting Xiao,Ni Zhao,Fei Chen,Liwei Chen,Jun Peng,Wanli Ma,Biao Xiao,Hongbin Wu,Xiangjian Wan,Yongshen Chen,Ruibing Chang,Cuihong Li,Zhishan Bo,Bian Ji,Wenjing Tian,Shuanghong Chen,Linhua Hu,Sungyuan Dai,Frederik C. Krebs

DOI: https://doi.org/10.1016/j.solmat.2013.06.029

2013-01-01

Abstract:A round robin study across 15 laboratories in China was carried out using single junction devices with an active area of 1cm2 and differently sized small module with an active area of 20 and 24cm2 respectively. The devices represented the state of the art in terms of processing as they did not employ indium or vacuum and were prepared using only printing and coating techniques on flexible substrates. The devices were studied in their flexible form and thus approach the vision of what the polymer solar cell is. The main purpose of the work was to establish and chart geographic and cultural differences in what constitutes a competent IV-characterization procedure and also to establish the spread in measured data across the globe. The main finding is that efficiency data deviated up to 30% from the mean while an overall relative standard deviation of 12% was observed. Collating this spread with previous findings points toward a seemingly region-independent i.e. global observation of the uncertainty in the IV-characterization of a polymer solar cell. Finally, we highlight what might be done to improve the accuracy of the reported data.
Critical Role of Non-Halogenated Solvent Additives in Eco-Friendly and Efficient All-Polymer Solar Cells

Saeah Kim,Huijeong Choi,Myeongjae Lee,Hyeseung Jung,Yukyung Shin,Seul Lee,Kyungkon Kim,Myung Hwa Kim,Kyungwon Kwak,BongSoo Kim

DOI: https://doi.org/10.3390/polym15061354

IF: 5

2023-03-09

Polymers

Abstract:Organic solar cells (OSCs) demonstrating high power conversion efficiencies have been mostly fabricated using halogenated solvents, which are highly toxic and harmful to humans and the environment. Recently, non-halogenated solvents have emerged as a potential alternative. However, there has been limited success in attaining an optimal morphology when non-halogenated solvents (typically o-xylene (XY)) were used. To address this issue, we studied the dependence of the photovoltaic properties of all-polymer solar cells (APSCs) on various high-boiling-point non-halogenated additives. We synthesized PTB7-Th and PNDI2HD-T polymers that are soluble in XY and fabricated PTB7-Th:PNDI2HD-T-based APSCs using XY with five additives: 1,2,4-trimethylbenzene (TMB), indane (IN), tetralin (TN), diphenyl ether (DPE), and dibenzyl ether (DBE). The photovoltaic performance was determined in the following order: XY + IN < XY + TMB < XY + DBE ≤ XY only < XY + DPE < XY + TN. Interestingly, all APSCs processed with an XY solvent system had better photovoltaic properties than APSCs processed with chloroform solution containing 1,8-diiodooctane (CF + DIO). The key reasons for these differences were unraveled using transient photovoltage and two-dimensional grazing incidence X-ray diffraction experiments. The charge lifetimes of APSCs based on XY + TN and XY + DPE were the longest, and their long lifetime was strongly associated with the polymer blend film morphology; the polymer domain sizes were in the nanoscale range, and the blend film surfaces were smoother, as the PTB7-Th polymer domains assumed an untangled, evenly distributed, and internetworked morphology. Our results demonstrate that the use of an additive with an optimal boiling point facilitates the development of polymer blends with a favorable morphology and can contribute to the widespread use of eco-friendly APSCs.

polymer science
Realizing the nanoscale quantitative thermal mapping of scanning thermal microscopy by resilient tip-surface contact resistance models.

Yifan Li,Tuo Ji,Jiahua Zhu,N. Mehra

DOI: https://doi.org/10.1039/C8NH00043C

2018-08-20

Nanoscale Horizons

Abstract:Quantitative assessment of thermal properties by scanning thermal microscopy (SThM) is a demanded technology, but still not yet available due to the presence of unpredictable thermal contact resistance (TCR) at the tip/substrate interface. The TCR is mainly affected by three major interfacial characteristics including surface roughness, hardness and contacting force. In this work, the TCR is mathematically derived into linear and non-linear models based on the interfacial micro-characteristics. The models have the capability to predict the TCR for both rough and smooth surfaces with satisfactory accuracy. With a predictable TCR, the heat transport across the tip/substrate nanointerface can be precisely described and thus quantitative thermal properties can be predicted from SThM measurements. The models are tested in three polymeric material systems, PDMS, epoxy and PVA. The thermal conductivity from the model prediction matches very well (<10% error) with the measured values from bulk polymer samples. Such models use general surface features as inputs, so they have wide applicability to other similar materials, especially polymers. Moreover, the models have been shown to be valid in doped PVA samples when extrapolated to predict thermal conductivity beyond the range of model development. This work extends the capability of SThM in quantitative measurement and enables a unique platform for thermal conductivity measurement at nanometer spatial resolution.

Engineering,Medicine,Materials Science,Physics
Time-Resolved Radio Frequency Conductivity (TRRFC) Studies of Charge-Carrier Dynamics in Aqueous Semiconductor Suspensions

H HERRMANN,ST MARTIN,MR HOFFMANN

DOI: https://doi.org/10.1021/j100045a025

1995-01-01

Abstract:The time-resolved radio-frequency conductivity (TRRFC) method provides a useful tool for in situ measurements of charge carrier dynamics in aqueous suspensions of semiconductor particles. In this report, the effects of pH on surface states of ZnO and the effects of hole scavengers (2-propanol) are examined. The experimental results are interpreted in terms of surface mediated recombination processes, in which holes are trapped in a fast process by surficial sites on the ZnO. Recombination rates appear to be governed by the reaction rate of electrons with surface-trap sites. At higher pH (i.e., pH 12), electrostatic repulsion due to a negatively charged ZnO surface leads to slower surface recombination rates compared to lower pH (i.e., pH 7) conditions. Addition of a hole scavenger significantly decreases the absolute charge-carrier concentration as detected by TRRFC. This decrease is attributed to the loss of trapped surface holes or surface-bound OH due to oxidation of the hole scavenger. When 2-propanol is used as a solvent, the holes react in a fast step with the solvent at the semiconductor interface within the time resolution of the experiment. The observed TRRFC signal is then due to electrons which are thought to be predominantly transferred to dissolved oxygen (O-2) leading to the formation of hydroperoxyl radicals (HO2) and subsequently hydrogen peroxide (H2O2).
Toward Fast Screening of Organic Solar Cell Blends

Artem Levitsky,Giovanni Maria Matrone,Aditi Khirbat,Ilaria Bargigia,Xiaolei Chu,Oded Nahor,Tamar Segal-Peretz,Adam J Moulé,Lee J Richter,Carlos Silva,Natalie Stingelin,Gitti L Frey

DOI: https://doi.org/10.1002/advs.202000960

2020-06-18

Abstract:The ever increasing library of materials systems developed for organic solar-cells, including highly promising non-fullerene acceptors and new, high-efficiency donor polymers, demands the development of methodologies that i) allow fast screening of a large number of donor:acceptor combinations prior to device fabrication and ii) permit rapid elucidation of how processing affects the final morphology/microstructure of the device active layers. Efficient, fast screening will ensure that important materials combinations are not missed; it will accelerate the technological development of this alternative solar-cell platform toward larger-area production; and it will permit understanding of the structural changes that may occur in the active layer over time. Using the relatively high-efficiency poly[(5,6-difluoro-2,1,3-benzothiadiazol-4,7-diyl)-alt-(3,3'''-di(2-octyldodecyl)-2,2';5',2'';5'',2'''-quaterthiophen-5,5'''-diyl)] (PCE11):phenyl-C61-butyric acid-methyl-ester acceptor (PCBM) blend systems, it is demonstrated that by means of straight-forward thermal analysis, vapor-phase-infiltration imaging, and transient-absorption spectroscopy, various blend compositions and processing methodologies can be rapidly screened, information on promising combinations can be obtained, reliability issues with respect to reproducibility of thin-film formation can be identified, and insights into how processing aids, such as nucleating agents, affect structure formation, can be gained.
Multifaceted Characterization Methodology for Understanding Nonidealities in Perovskite Solar Cells: A Passivation Case Study

Jonathan Parion,Santhosh Ramesh,Sownder Subramaniam,Henk Vrielinck,Filip Duerinckx,Hariharsudan Sivaramakrishnan Radhakrishnan,Jef Poortmans,Johan Lauwaert,Bart Vermang

DOI: https://doi.org/10.1002/solr.202400529

IF: 9.1726

2024-09-21

Solar RRL

Abstract:Characterization is used for the study of surface treatment in perovskite solar cells. Current–voltage measurements show a 90 mV increase in open‐circuit voltage, 11 % increase in fill‐factor and 4 % increase in efficiency. Capacitance‐based measurements show an increase in ionic resistance in the perovskite bulk and an activation energy of 0.41 eV, pointing toward a reduction in ion‐assisted charge carrier recombination. A multifaceted characterization approach is proposed, aiming to establish a link between nanoscale electrical properties and macroscale device characteristics. Current–voltage (I–V) measurements are combined with admittance spectroscopy (AS) and deep‐level transient spectroscopy (DLTS) for the analysis of charge‐related performance losses with time‐of‐flight secondary‐ion mass spectrometry to complete the understanding of ionic motion in the device. This is applied to the study of surface treatment in perovskite solar cells, which implements several strategies to improve band alignment, perovskite grain growth, and chemical passivation. An increase of both open‐circuit voltage (Voc) and fill factor of respectively 90 mV and 11% is shown after surface treatment, with an absolute efficiency increase of 4%. AS measurements, coupled with a lumped elements model, rule out the impact of transport layers as the origin of the performance improvement, rather pointing toward a reduction in ionic resistance in the perovskite bulk. Analysis of the DLTS response yields an activation energy of 0.41 eV, which is likely related to the same ionic mechanism discovered with AS. Finally, both of these techniques enable to show that the surface treatment main contribution is to reduce ion‐related recombination of charge carriers.

energy & fuels,materials science, multidisciplinary
Unraveling the Correlations between Mechanical Properties, Miscibility, and Film Microstructure in All‐Polymer Photovoltaic Cells

Kangkang Zhou,Kaihu Xian,Qingchun Qi,Mengyuan Gao,Zhongxiang Peng,Junwei Liu,Yang Liu,Saimeng Li,Youdi Zhang,Yanhou Geng,Long Ye

DOI: https://doi.org/10.1002/adfm.202201781

IF: 19

2022-05-08

Advanced Functional Materials

Abstract:The key mechanical properties of five all‐polymer photovoltaic blend films are determined with a set of complementary characterization methods. The composition dependences of the film stretchability and elastic moduli of these all‐polymer blends with different miscibility are well elucidated. Notably, the elastic moduli of these all‐polymer blend films with various morphologies can be predicted by mechanical models for the first time. The rapid development of low bandgap polymer acceptors has promoted the efficiency up to ≈17% for all‐polymer solar cells (all‐PSCs). Nevertheless, the polymeric blend film, core to the photoelectric conversion of all‐PSCs, has not been thoroughly understood in terms of the influence and regulatory factors of mechanical properties, which hinders the advances in flexible and wearable applications. Herein, a range of characterization methods is combined to investigate the mechanical properties, miscibility, and film microstructure of the blends based on several representative polymer donors (PTzBI‐Si, PTVT‐T, PM6 and PTQ10) and a benchmark polymer acceptor N2200, and to further reveal the miscibility‐property relationships of the miscibility property. The results stress that fracture behaviors and elastic moduli of these blends with varied compositions show different changing trends, which are affected by molecular interactions and aggregated structure of the blends. The elastic moduli of the four all‐polymer blends can be nicely predicted by different models that are deduced from macromolecular mechanics. Most crucially, the correlations between elastic modulus, morphology, and miscibility of all‐polymer blends are elucidated for the first time. The derived relationships is validated with another high‐efficiency blend and will be the key to the successful fabrication of mechanically robust and stretchable all‐PSCs with high efficiency.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
In situ monitoring drying process to disclose the correlation between molecular weights of polymer acceptor with flexible spacer and performance of all-polymer solar cells

Jiale Xiang,Sven Englund,Zewdneh Genene,Guanzhao Wen,Yanfeng Liu,Nannan Yao,Rui Zhang,Leiqiang Qin,Lei Wang,Ergang Wang,Wei Zhang,Fengling Zhang

DOI: https://doi.org/10.1039/d4tc02217c

IF: 6.4

2024-07-18

Journal of Materials Chemistry C

Abstract:Molecular weight (Mn) and conjugation of polymers can profoundly influence the performance of all-polymer solar cells (all-PSCs) via nanostructures of bulk heterojunctions (BHJs). To study the correlation between Mn and the performance of all-PSCs based on acceptor with flexible conjugation-break spacer (FCBS), three batches of acceptors, named PYTS, were synthesized with different number-average Mn from 9, 13 to 19 kDa. Blends with a polymer donor PBDB-T, the all-PSCs based on PYTS with Mn of 9 kDa and 19 kDa exhibit power conversion efficencies (PCE) of 5.99% and 9.43%, respectively, primarily due to increased short-circuit current density (Jsc) from 13.02 to 18.73 mA cm-2. To disclose the impact of Mn on device performance, dynamics of mixed PBDB-T:PYTS solutions to solid BHJs is studied by monitoring the drying process with a home-made in situ multifunctional spectroscopy, which demonstrates that PYTS with Mn of 19 kDa has a longer drying time of the PYTS with Mn of 9 kDa. Prolonged drying of the BHJs with higher Mn PYTS facilitates more tightly packed structures with higher crystallinity. A systematic investigation on the nanostructions of BHJs, charge generation, transport and recombination is carried out with grazing-incidence wide-angle X-ray scattering (GIWAXS), transient absorption spectroscopy (TAS) and characterization of all-PSCs. The results indicate that increased crystallinity in the BHJs benefits exciton dissociation, electron transport, prolonged carrier lifetimes, and decreased non-geminate recombination rate constants in the corresponding devices. Combining the in situ study of drying and the investigation on films and devices provides us a comprehensive understanding of the interplay between Mn, the drying process, the nanostructures of BHJs and device performance. This work not only emphasizes the essential role of Mn in governing the device performance, but also exhibits recorded film formation through the in situ spectroscopy, enabling us to manipulate the nanostructure of BHJs by optimizing Mn of polymers and processing parameters.

materials science, multidisciplinary,physics, applied
Exploring the impact of solvent additives on dielectric properties in polymer photovoltaics: A deconvolution and in-depth study of electrical modulus, complex conductivity, and impedance responses

Soumia Zaim,Abderrahmane Elmlouky,Mohamed Monkade,Reddad Elmoznine

DOI: https://doi.org/10.1016/j.molliq.2024.125004

IF: 6

2024-05-18

Journal of Molecular Liquids

Abstract:Impedance and dielectric spectroscopy is a well-known technique for characterizing interfaces, especially donor/receiver interfaces in bulk heterojunction (BHJ) solar cells. This technique was employed to investigate the interface of poly (4,8-bis-alkyloxybenzo(1,2-b:4,5-b0) dithio-phene-2,6-diyl-alt- (alkyl thieno (3,4-b) thiophene-2-carboxylate)-2,6-diyl) (PBDTTT-C): PC70BM in bulk heterojunction with DIO as additive. For this reason, a simulation was carried out to generate the complex impedance, modulus, and complex conductivity data based on the electrical parameters extracted from the equivalent circuit. Therefore, a new approach based on the coupling of complex functions such as impedance, modulus, and conductivity has been proposed. In addition, an extrapolation and deconvolution approaches are used to highlight the relaxation processes, the BHJ layer process, the two electrical contacts of the interfaces between PEDOT: PSS/PBDTTT-C: PC70BM and PBDTTT-C: PC70BM/Ca process, and the electrode polarization process. In the next step, the remove the low-frequency process enhances the visibility of other processes, particularly observable in the evolution of the electrical modulus and the conduction parameters associated with each process. In the complex functions, there was a good correlation between all parameters derived from both processes. The characteristics of the conduction processes, such as conductivity values at low and high frequencies and ionic strength were then extracted. All these parameters were evaluated and discussed as a function of the thickness of the active layer. Finally, we demonstrate that the electrical modulus and complex conductivity can be perfect tools to characterize the donor/acceptor interfaces.

chemistry, physical,physics, atomic, molecular & chemical
Towards validation of combined-accelerated stress testing through failure analysis of polyamide-based photovoltaic backsheets

Michael Owen-Bellini,Stephanie L Moffitt,Archana Sinha,Ashley M Maes,Joseph J Meert,Todd Karin,Chris Takacs,Donald R Jenket,James Y Hartley,David C Miller,Peter Hacke,Laura T Schelhas

DOI: https://doi.org/10.1038/s41598-021-81381-7

2021-01-21

Abstract:Novel methods for advancing reliability testing of photovoltaic (PV) modules and materials have recently been developed. Combined-accelerated stress testing (C-AST) is one such method which has demonstrated reliable reproduction of some field-failures which were not reproducible by standard certification tests. To increase confidence and assist in the development of C-AST, and other new testing protocols, it is important to validate that the failure modes observed and mechanisms induced are representative of those observed in the field, and not the product of unrealistic stress conditions. Here we outline a method using appropriate materials characterization and modelling to validate the failure mechanisms induced in C-AST such that we can increase confidence in the test protocol. The method is demonstrated by applying it to a known cracking failure of a specific polyamide (PA)-based backsheet material. We found that the failure of the PA-based backsheet was a result of a combination of stress factors. Photo-oxidation from ultra-violet (UV) radiation exposure caused a reduction in fracture toughness, which ultimately lead to the cracking failure. We show that the chemical and structural changes observed in the backsheet following C-AST aging were also observed in field-aged samples. These results increase confidence that the conditions applied in C-AST are representative of the field and demonstrates our approach to validating the failure mechanisms induced.
Comprehensive Study of Carrier Recombination in High‐Efficiency CdTe Solar Cells Using Transient Photovoltage

Abasi Abudulimu,Steven Carter,Adam B. Phillips,Deng‐Bing Li,Sabin Neupane,Tyler Brau,Jared Friedl,Ebin Bastola,Manoj K. Jamarkattel,Michael J. Heben,Yanfa Yan,Randy J. Ellingson,Deng-Bing Li

DOI: https://doi.org/10.1002/solr.202400131

IF: 9.1726

2024-04-06

Solar RRL

Abstract:Cadmium telluride (CdTe) solar cells represent a commercially successful photovoltaic technology, with an annual production capacity approaching 20 GW. However, improving the open‐circuit voltage (V OC ) remains challenging. This study aims to deepen the understanding of charge carrier recombination in CdTe solar cells and to explore alternative dynamical characterization methods that address the limitations found in conventionally used time‐resolved photoluminescence (TRPL) for CdTe solar cells. We utilized transient photovoltage (TPV) and transient photocurrent (TPC) techniques to investigate charge carrier dynamics under conditions resembling real‐world solar cell operation. Our results reveal that an effective non‐radiative recombination lifetime of 580 ns dominates the charge dynamics at VOC values below 850 mV. Above this threshold, radiative recombination becomes significant, with a radiative recombination coefficient of 1.1×10‐9 cm3 s‐1. Additionally, the stationary charge carrier density at 1 sun was determined to be around 1×1014 cm‐3. By accurately determining both radiative and non‐radiative recombination, this work provides a comprehensive understanding of carrier dynamics in high‐performing CdTe devices and paves the way for improving the VOC and performance of CdTe solar cells. This article is protected by copyright. All rights reserved.

energy & fuels,materials science, multidisciplinary

Validation of Time-Resolved Microwave Conductivity (TRMC) As a Screening Tool for All-Polymer Solar Cells

Non-resonant phase sensitive approach for time resolved microwave conductivity in photoactive thin films

Matrix Organization and Merit Factor Evaluation as a Method to Address the Challenge of Finding a Polymer Material for Roll Coated Polymer Solar Cells

Detailed investigation of TLM contact resistance measurements on crystalline silicon solar cells

Real-time monitoring polymerization degree of organic photovoltaic materials toward no batch-to-batch variations in device performance

Machine Learning for Ultra High Throughput Screening of Organic Solar Cells: Solving the Needle in the Haystack Problem

Experimental Validation of Optimized Solar Cell Capacitance Simulation for Rheology‐Modulated Carbon‐Based Hole Transport Layer‐Free Perovskite Solar Cell

Machine learning for ultra high throughput screening of organic solar cells: Solving the needle in the hay stack problem

Advancing Accuracy in Perovskite Tandem Solar Cell Efficiency via Transfer Matrix-Based Realistic Device Simulations

Machine learning-based screening of complex molecules for polymer solar cells

A Round Robin Study of Polymer Solar Cells and Small Modules Across China

Critical Role of Non-Halogenated Solvent Additives in Eco-Friendly and Efficient All-Polymer Solar Cells

Realizing the nanoscale quantitative thermal mapping of scanning thermal microscopy by resilient tip-surface contact resistance models.

Time-Resolved Radio Frequency Conductivity (TRRFC) Studies of Charge-Carrier Dynamics in Aqueous Semiconductor Suspensions

Toward Fast Screening of Organic Solar Cell Blends

Multifaceted Characterization Methodology for Understanding Nonidealities in Perovskite Solar Cells: A Passivation Case Study

Unraveling the Correlations between Mechanical Properties, Miscibility, and Film Microstructure in All‐Polymer Photovoltaic Cells

In situ monitoring drying process to disclose the correlation between molecular weights of polymer acceptor with flexible spacer and performance of all-polymer solar cells

Exploring the impact of solvent additives on dielectric properties in polymer photovoltaics: A deconvolution and in-depth study of electrical modulus, complex conductivity, and impedance responses

Towards validation of combined-accelerated stress testing through failure analysis of polyamide-based photovoltaic backsheets

Comprehensive Study of Carrier Recombination in High‐Efficiency CdTe Solar Cells Using Transient Photovoltage