Abstract:Grain boundary (GB) strengthening of metallic materials faces limitations as grain sizes are reduced to the nanoscale, primarily due to the transition from the strengthening to the softening effects. Understanding the intrinsic mechanisms behind such pronounced transitions is essential for optimizing the mechanical properties of nanocrystalline (NC) alloys. In this work, the critical grain size responsible for this transition is determined for NC CoCrNi medium-entropy alloys using molecular dynamics simulation, and the underlying mechanisms concerning varying temperatures and strain rates are systematically investigated for the samples with the critical grain size. The transition from Hall-Petch (HP) strengthening to Inverse Hall-Petch (IHP) softening is established by decreasing the average grain sizes from 21 nm to 3 nm. The critical grain size for the current alloys is estimated to be 12 nm, and the underlying deformation mechanisms are illustrated as follows: In the IHP regime, GB-mediated deformation becomes dominant, leading to softening. Conversely, in the HP regime, dislocation slip dominates the deformation mode, contributing to strengthening. It is found that an increase in temperature from 77 K to 1100 K leads to a decrease in the average flow stress and Young's modulus. Meanwhile, the deformation mechanisms change from dislocation slip (77K-700K) to GB-mediated deformation (700 K-1100 K). Furthermore, the underlying mechanisms correlating to the critical strain rate are uncovered. It can be attributed to the shift in deformation mechanisms from dislocation slip at relatively low strain rate regimes (5 x 10(7) s(-1)-2 x 10(9) s(-1)) to dislocation drag at relatively high strain rate regimes (2 x 10(9) s(-1)-5 x 10(9) s(-1)). Our atomistic insights into the tensile response of NC CoCrNi may provide a crucial basis for designing superior properties to meet the growing demands of advanced engineering fields.

Hall-petch Relationship and Strain Rate Sensitivity of Nanocrystalline Mg - 5wt% A1 Alloy

Deformation Behaviour of Nanocrystalline Mg-Al Alloys During Nanoindentation

Hall-Petch relationship and deformation mechanism of pure Mg at room temperature

Precipitation Size and Strain Rate Dependence of Dislocation-Amorphous Nanopillar Interaction Mechanism in Magnesium

Effect of Grain Size on Tensile Deformation Behavior of Nano-Polycrystalline Al and Al–Mg Alloys with Grain Boundary Segregation of Mg

Effect of Grain Size, Temperature, and Tensile Strain Rate on Mechanical Response of CoCrNi Medium-Entropy Alloys

Unraveling the Strain-Dependent Hall-Petch Slope in Low-to-high Mg Content Al-Mg Alloys

Influence of Grain Size on Strain Rate Sensitivity in Rolled Mg–3Al–3Sn Alloy at Room Temperature

Atomic Simulation of Mechanical Behavior of Mg in A Super-Lattice of Nanocrystalline Mg and Amorphous Mg-Al Alloy

Atomic-scale Analysis of Deformation Behavior of Face-Centered Cubic Nanocrystalline High-Entropy Alloys with Different Grain Sizes at High Strain Rates

Twinning-Induced Abnormal Strain Rate Sensitivity and Indentation Creep Behavior in Nanocrystalline Mg Alloy.

Grain-size effect on the deformation of Mg–3Al–3Sn alloy: Experiments and elastic-viscoplastic self-consistent modeling

Effect of Grain Size on Mechanical Property of Mg–3Al–1Zn Alloy

Mapping the Strain-Rate and Grain-Size Dependence of Deformation Behaviors in Nanocrystalline Face-Centered-cubic Ni and Ni-based Alloys

Influence of Grain Size on Deformation Mechanisms in Rolled Mg–3Al–3Sn Alloy at Room Temperature

Orientation dependence of intracrystalline and grain boundary deformation behavior in Mg-2Y using nanoindentation and CPFEM

Breaks in the Hall-Petch Relationship after Severe Plastic Deformation of Magnesium, Aluminum, Copper, and Iron

Influence of Texture on Hall–Petch Relationships in an Mg Alloy

Nanoscale Deformation of Multiaxially Forged Ultrafine-Grained Mg-2Zn-2Gd Alloy with High Strength-High Ductility Combination and Comparison with the Coarse-Grained Counterpart

Influence of Mg Content, Grain Size and Strain Rate on Mechanical Properties and DSA Behavior of Al-Mg Alloys Processed by ECAP and Annealing

Hot deformation behavior of novel high-strength Mg-0.6Mn-0.5Al-0.5Zn-0.4Ca alloy