Abstract:The complex process and thermal behavior of laser additive manufacturing will lead to complex microstructure and property evolution. In order to enhance the processing efficiency of a high-strength Al-4.2Mg-0.4Sc-0.2Zr alloy fabricated by laser powder bed fusion (LPBF) additive manufacturing, a temperature gradient induced ductile-brittle transition behavior caused by changes in laser scanning speed for LPBF processed Al-4.2Mg-0.4Sc-0.2Zr alloy was reported in this study. As the laser scan speed increased from 0.4 ms -1 to 2.4 ms -1 , a transition in fracture mode from toughness to brittleness was observed, where the tensile strength was decreased from 547.6 MPa to 472.3 MPa while the elongation decreased from 13.8% to 1.9%. Based on transmission electron microscopy (TEM) and electron backscatter diffraction (EBSD) characterizations, it was attributed to the cross-scale different microstructures from mesoscopic to microscopic as laser scan speed increased, including (i) more porosity in microscale (~30 μm), (ii) slenderer coarse grains and narrow equiaxed grain regions within melt pools in sub-microscale (~1 μm) and (iii) suppression of the Mg segregation along grain boundaries and formation of higher dislocation densities and stacking faults in the nanoscale (~200 nm). These changes in the microstructure caused the specimens processed with high scan speeds (above 1.6 ms -1 ) to be more prone to initiation of cracks during tensile, the ability of synergistic deformation between grains to decrease, and the bonding strength between grains to reduce. By simulating the thermal field of the melt pool, the formation mechanism of the different microstructures was ascribed to the different temperature gradients, which further determined the grain structures and element distributions. This work demonstrated that the structure and properties of LPBF processed high-performance Al alloys can be well tailored by processing parameter control.

Influence of Thermal Effects Via Powder Bed Fusion on the Graded Microstructure and Mechanical Properties of Near-Β Ti–5Al–5Mo–5V–3Cr–1Zr Alloy

Mechanical Properties and Fracture Behavior of Laser Powder-Bed-Fused GH3536 Superalloy

Process-structure-property Modeling for Postbuild Heat Treatment of Powder Bed Fusion Ti-6Al-4V

Influence of Powder Bed Temperature on the Microstructure and Mechanical Properties of Ti-6Al-4V Alloy Fabricated via Laser Powder Bed Fusion

Deep Cryogenic and Thermal Aging Treatments of Ti‐5Al‐5Mo‐5V‐3Cr Alloy Additively Manufactured by Powder Bed Fusion‐Laser Beam

Laser Powder Bed Fusion of Titanium Aluminides: An Investigation on Site-Specific Microstructure Evolution Mechanism

Unravelling heterogeneities in sub-grain cellular structure and micromechanical response of additive manufactured Ti-Nb alloys

Influence of the physicochemical properties of reusable powders on the mechanical properties of Ti6Al4V manufactured via laser powder bed fusion additive manufacturing

The influence of post-thermal treatments on microstructure and mechanical properties in A20X alloy fabricated through powder bed fusion

Effect of high preheating on the microstructure and mechanical properties of high gamma prime Ni-based superalloy manufactured by laser powder bed fusion

Material Characterisation and Computational Thermal Modelling of Electron Beam Powder Bed Fusion Additive Manufacturing of Ti2448 Titanium Alloy

Effects of different heat treatment temperatures on the microstructure and mechanical properties of additive manufacturing Ti65 alloys

The impact of heat treatment on microstructure, residual stress, and mechanical behavior of laser powder bed fusion additively manufactured Ti–6Al–2Sn–4Zr–2Mo alloy

Temperature gradient induced tough-brittle transition behavior of a high-strength Al-4.2Mg-0.4Sc-0.2Zr alloy fabricated by laser powder bed fusion additive manufacturing

Research Viewpoint on Performance Enhancement for Very-High-Cycle Fatigue of Ti-6Al-4V Alloys via Laser-Based Powder Bed Fusion

Comparison of microstructure, crystallographic texture, and mechanical properties in Ti–15Mo–5Zr–3Al alloys fabricated via electron and laser beam powder bed fusion technologies

Effect of Aging Temperature on Microstructure, Mechanical, and Wear Properties of 18Ni-300 Maraging Steel Produced by Powder Bed Fusion

Towards uniform and enhanced tensile ductility of additively manufactured Ti−5Al−5Mo−5V−3Cr alloy through designing gradient interlayer deposition time

Tailoring the microstructure and mechanical property of laser powder bed fusion fabricated Ti–6Al–2Sn–4Zr–2Mo via heat treatment

Achieving superior strength-ductility combination in the heterogeneous microstructured Ti64 alloy via multi-eutectoid elements alloying with CoCrFeNiMn during laser powder bed fusion

Laser powder bed fusion of nano-titania modified 2219 aluminium alloy with superior mechanical properties at both room and elevated temperatures: The significant impact of solute