Abstract:Nowadays, the number of emergency situations related to fires is quite high. The high percentage of human deaths is mainly due to poisoning by gaseous toxic substances including carbon monoxide. The most problematic issue is the development or application of existing catalysts in means of individual protection of human respiratory organs – respirators, gas masks, self-rescuers. The compositions based on thermally modified tripoli obtained by the method of impregnation of the carrier by moisture content with compounds of copper(II), palladium(II) and potassium bromide were investigated. According to X-ray phase analysis, it was established that thermally modified tripoli is a polyphase crystalline mineral containing the following main phases: a-quartz, a-tridymite, b-cristobalite, a-cristobalite. The influence of the initial concentration of CO, which does not exceed 15 MPC, on the kinetic and stoichiometric parameters of the reaction varied in the range from 100 to 300 mg/m3. It was noted that the reaction rate in the stationary mode (Wst) is directly proportional to the increase in the initial concentration of carbon monoxide in the gas phase. The values of the constant kI and the degree of CO conversion (ηst) do not depend on CinCO, which also confirms the first order of CO concentration. Particular attention is paid to the aspects of ensuring protection against carbon monoxide when its concentration exceeds 15 MPC. Usually, special equipment, such as filtering self-rescuers, is used to clean the air from carbon monoxide at concentrations from 1000 to 6500 mg/m3. The catalyst developed by us is intended for use in lightweight personal respiratory protective equipment (RPE) at concentrations not exceeding 15 MPC. Therefore, there was an interest in researching the possibilities of using this catalyst in the self-saving filter system. The concentration of carbon monoxide in the gas-air mixture was varied from 400 to 2500 mg/m3 in the presence of the К2PdCl4-Cu(NO3)2-КBr/300-Tr(K) system. It was established that Wst increases in direct proportion with an increase in the gas-air mixture up to 1250 mg/m3, which indicates the first order of the reaction according to carbon monoxide. It was found that at CinCO = 1000 mg/m3 only under the condition τ ́ = 1.13 s (mk = 10 g) the К2PdCl4-Cu(NO3)2-KBr/Tr catalyst provides air purification below the breakthrough CO concentration (CfCO = 200 mg/m3). Experiments on the influence of SO2 on the activity of carbon monoxide oxidation catalysts have shown that they lose their activity, so in air purification systems from CO, it is necessary to provide for the stage of capturing sulfur dioxide.

A Novel Approach for Active and Synchronous Removal of Fire-Generated CO Based on Co-La0.1 Catalyst: from Lab-Scale to Full-Scale Tests

A novel approach for active and synchronous removal of fire-generated CO based on Co-La 0.1 catalyst: From lab-scale to full-scale tests

A Catalyst Powder-Based Spraying Approach for Rapid and Efficient Removal of Fire-Generated CO：From Laboratory to Pilot Scale.

A catalyst powder-based spraying approach for rapid and efficient removal of fire-generated CO:From laboratory to pilot scale

Rapid and efficient removal of CO in CH4 and CH4/coal dust hybrid explosions: A novel approach of spraying catalyst powder

Low Temperature CO Catalytic Oxidation and Kinetic Performances of KOH-Hopcalite in the Presence of CO2

Research on an In-situ Synchronous CO Elimination Method in Blasting Operations and Engineering Experimental Application Based on Nano-CO Catalysts

Enhancing low-temperature CO removal in complex flue gases: A study on La and Cu doped Co3O4 catalysts under real-world combustion environment

Catalytic Destruction of A Surrogate Organic Hazardous Air Pollutant As A Potential Co-Benefit for Coal-Fired Selective Catalytic Reduction Systems

Three-Dimensional Spherical CuCoAlO<sub>X</sub> Catalyst with a Micro-/ Nanoporous Structure for Low-Temperature CO-SCR Denitration

Three-Dimensional Spherical CuCoAlO<sub><i>x</i></sub> Catalyst with a Micro-/Nanoporous Structure for Low-Temperature CO-SCR Denitration

CATALYST BASED ON PALLADIUM(II), COPPER(II) COMPOUNDS AND THERMALLY-MODIFIED TRIPOLI FOR THE PREPARATION OF RESPIRATORY REMEDIES FROM CARBON MONOXIDE IN EMERGENCY SITUATIONS

Simultaneous abatement of NO x and CO using tandem catalyst system via reactant- and energy- Co-promoting effect

Novel insights for simultaneous NOx and CO Removal: Cu+-Sm3+-Ov-Ti4+ asymmetric active site promoting NH3-SCR coupled with CO oxidation reaction

Increasing Cerium Dispersion Favours Lattice Oxygen Activity of Cobalt Oxides for CO Catalytic Combustion

Catalytic polymer self-cleavage for CO2 generation before combustion empowers materials with fire safety

Engineering Co3O4@3DOM LaCoO3 multistage-pore nanoreactor with superior SO2 resistance for toluene catalytic combustion

Effect of Co3O4 Powder on the Explosion Characteristics and CO Products of Methane-Air Mixture

MOFs-derived self-sacrificing template strategy to double-shelled metal oxides nanocages as hierarchical interfacial catalyst for suppressing smoke and toxic gases releases of epoxy resin

Theoretical Investigation of Chemical Reaction Kinetics of CO Catalytic Combustion over NiNx-Gr

Theoretical Study on the Reaction Kinetics of CO Oxidation by Nitrogen-Doped Graphene Catalysts with Different Ligand Structures