Abstract:Anion exchange membrane fuel cell (AEMFC) has attracting great attention as one of the most clean energy conversion technologies, because it has a facile electrochemical kinetics under alkaline condition and enables the use of non-precious metal catalysts. The reported anion exchange membranes were usually prepared by tethering quaternary ammonium groups (QA) to the backbone of chloromethylated or bromomethylated aromatic polymers by immersing in trimethylamine solution. However, they exhibit much low ionic conductivity and poor alkaline stability, which hinders the further development of AEMFC technology. In order to improve the ionic conductivity of anion exchange membranes, we located multi QA groups on one side chains for enhancing the local density of ionic groups. Therefore, we synthesized a type of small molecule with a quaternary ammonium group and an alkyl bromide. After gethering it onto 1,4-diazabicyclo[2.2.2] octane-functionalized poly(arylene ether ketone) by a quaternization reaction, tri-quaternized poly(arylene ether ketone) (TQPAEK) was successfully prepared with flexible side chains containing multi quaternary ammonium groups. Then a series of anion exchange membranes in OH- form were obtained by solution casting and then alkaline treatment. The ionic exchange capacity of these membranes in the range of 1.75-2.57 meq/g could be adjusted by controlling the degree of bromination of the precursor polymer. The water uptake, swelling ratio and hydroxide conductivity of TQPAEK membranes increased with the increasing IEC values. They also showed good thermal and mechanical stabilities. Especially, the introduction of flexible side chains significantly improved the elongation at the break of membranes, which reached up to 103.2%. Meanwhile, the tensile stress was still higher than 28 MPa. AFM images showed that the hydrophilic/hydrophobic phase-separation morphology was formed in these TQPAEK containing multi-quaternized flexible side chains. Therefore, TQPAEK exhibited high ionic conductivity of 74.35 mS/cm at 80 degrees C. The results indicated that TQPAEK membranes had the potential to be used in alkaline AEMFCs.

Towards Highly Conducting and Stable Poly(fluorenyl Biphenyl)-Based Anion Exchange Membranes by Grafting Dual Y-shaped Side-Chains

Facile Preparation of Novel Cardo Poly(oxindolebiphenylylene) with Pendent Quaternary Ammonium by Superacid-Catalysed Polyhydroxyalkylation Reaction for Anion Exchange Membranes

Poly(olefin)-Based Anion Exchange Membranes Prepared Using Ziegler–Natta Polymerization

Facile Preparation of an Ether-Free Anion Exchange Membrane with Pendant Cyclic Quaternary Ammonium Groups

Novel Cross-Linked Anion Exchange Membranes with Diamines As Ionic Exchange Functional Groups and Crosslinking Groups

Highly conductive fluorine-based anion exchange membranes with robust alkaline durability

Diamine Crossklinked Anion Exchange Membranes Based on Poly(vinyl Benzyl Methylpyrrolidinium)

Poly(arylene Ether Nitrile) Anion Exchange Membranes with Dense Flexible Ionic Side Chain for Fuel Cells

Highly Ion-Conductive and Alkaline Stable Anion Exchange Membranes Containing Bulky Aryl Units and Symmetric Bis-Piperidinium Branches

Durable Poly(binaphthyl-Co-p-terphenyl Piperidinium)-Based Anion Exchange Membranes with Dual Side Chains

Novel Anion Exchange Membranes Based on Quaternized Diblock Copolystyrene Containing a Fluorinated Hydrophobic Block

Novel crosslinked aliphatic anion exchange membranes with pendant pentafluorophenyl groups

A High-Performance Anion Exchange Membrane Based on Poly(arylene Ether Sulfone) with a High Concentration of Quaternization Units

Synthesis and characterization of ion exchange capacity controlled and self-crosslinked anion exchange membranes

Preparation and Properties of Anion Exchange Membranes Based on Multiple Quaternary Ammonium Groups

Construction of Crosslinked Polybenz Imidazole-Based Anion Exchange Membranes with Ether-Bond-free Backbone

Highly conductive and dimensionally stable anion exchange membranes enabled by rigid poly(arylene alkylene) backbones

Poly(fluorenyl Ether Ketone)s with Densely Distributed Multi-Cationic Side Chains for Anion Exchange Membranes

Highly conductive fluorinated poly(biphenyl piperidinium) anion exchange membranes with robust durability

Towards high alkaline stability and fuel cell performance in anion exchange membranes via backbone−cation alkylene spacer tuning for quaternized poly(biphenylene alkylene)s

Dual-cation Comb-Shaped Anion Exchange Membranes: Structure, Morphology and Properties