Fault Diagnosis for Linear Discrete Time-Varying Systems and Its Applications

Maiying Zhong,Ting Xue,Steven X. Ding,Donghua Zhou

DOI: https://doi.org/10.1007/978-981-19-5438-2

2023-01-01

Abstract:This book focuses on fault diagnosis for linear discrete time-varying (LDTV) systems and its applications in modern engineering processes

What problem does this paper attempt to address?

Delay-dependent fault detection for switched linear systems with time-varying delaysthe average dwell time approach

Dan Zhang,Li Yu,Wen-an Zhang

DOI: https://doi.org/10.1016/j.sigpro.2010.08.016

IF: 4.729

2011-01-01

Signal Processing

Abstract:In this paper, the fault detection problem is investigated for a class of discrete-time switched linear systems with time-varying delays. The main purpose is to design a fault detection filter such that, for all unknown inputs, control inputs and time delays, the estimation error between the residual and fault is minimized in an exponential way. The fault detection problem is converted into an exponential H ∞ filtering problem. By using a newly constructed Lyapunov functional and the average dwell time scheme, a novel delay-dependent sufficient condition for the solvability of this problem is established in terms of linear matrix inequalities (LMIs). A numerical example is given to demonstrate the effectiveness of the developed theoretical results. © 2010 Elsevier B.V. All rights reserved.
A survey on model-based fault diagnosis for linear discrete time-varying systems

Maiying Zhong,Ting Xue,Steven X. Ding

DOI: https://doi.org/10.1016/j.neucom.2018.04.037

IF: 6

2018-09-01

Neurocomputing

Abstract:To meet the rising demands for safety and reliability of modern industrial control systems, the model-based fault diagnosis problem has attracted much attention in the past few decades both from the academic communities and in practical applications. Among the rich body of literature, the majority of the results are proposed for linear time invariant systems despite the fact that most practical processes are inherently time-varying by nature and discretized for online implementations. Recently, with the ever-increasing system complexity and scale, the model-based fault diagnosis issue for linear discrete time-varying (LDTV) systems has become a hot research topic of both theoretical importance and practical significance, and a great number of results have been reported with many open problems deserving further investigation. To reflect the latest progress in this emerging research branch, this survey aims to provide a timely reference to readers interested in this topic. More specifically, in this survey, the techniques for model-based fault diagnosis for LDTV systems are classified into observer-based methods, parity space-based approaches and parameter estimation schemes, which constitute the three main parts of this survey. The background and the latest progress for each class of these techniques are comparatively discussed with particular focuses on the fault detection and the fault estimation issues. Additionally, an overview on their practical applications to specific industrial plants is provided. Furthermore, the possible future research directions concerning the model-based fault diagnosis for LDTV processes are pointed out, followed by comprehensive concluding remarks.

computer science, artificial intelligence
Technology and Development of Fault Diagnosis Based on Graph Theory

吴军强,梁军

DOI: https://doi.org/10.3969/j.issn.1001-4551.2003.05.070

2003-01-01

Abstract:Theories and applications of process fault diagnosis (FD) based on graph theory are presented, and research results within this field are shortly overviewed in this paper. There are two topics about the method being given: fault propagation digraph and signed directed graph( SDG) .
A Variable Moving Window Approach for On-Line Fault Diagnosis in Industrial Processes

Shaoyuan Zhou,Lei Xie,Shuqing Wang

DOI: https://doi.org/10.1109/wcica.2004.1340975

2004-01-01

Abstract:Although there are many literatures on process on-line fault diagnosis, the moving window of fixed length is used in most of cases. In this study, an approach based on hidden Markov model (HMM) for on-line fault diagnosis in industrial processes is proposed. In variable moving window, the length of which is modified with time, is applied to track process dynamic variables. Before fault diagnosis, the process operating condition is monitored using principal component analysis (PCA) until abnormal operation in the process is detected. Case studies from the Tennessee Eastman plant illustrate that the proposed method is effective.
Fault Diagnosis and Application to Modern Systems 2018

Xiao He,Zidong Wang,Gang Li,Zhijie Zhou,Youqing Wang

DOI: https://doi.org/10.1155/2018/8460541

2017-01-01

Journal of Control Science and Engineering

Abstract:1Department of Automation, Beijing National Research Center for Information Science and Technology (BNRist), Tsinghua University, Beijing 100084, China 2Department of Computer Science, Brunel University London, London UB8 3PH, UK 3Xi’an High-Tech Institute, Xi’an 710025, China 4College of Electrical Engineering and Automation, Shandong University of Science and Technology, Qingdao 266590, China 5State Key Laboratory of Synthetical Automation for Process Industries, Northeastern University, Shenyang, Liaoning 110819, China
Optimal Fault Detection for Linear Discrete Time-Varying Systems

Maiying Zhong,Donghua Zhou,Steven X. Ding

DOI: https://doi.org/10.1016/j.automatica.2010.05.022

IF: 6.4

2010-01-01

Automatica

Abstract:This paper deals with the problem of observer-based fault detection for linear discrete time-varying (LDTV) systems. A problem formulation is first proposed to address the optimization of the fault detection filter (FDF) design, which is expressed in terms of maximizing a finite horizon H∞/H∞ or H−/H∞ performance index. This formulation can be applied to FDF design of LDTV systems subject to l2-norm bounded unknown inputs or stochastic noise sequences. It is shown that a unified optimal solution to the FDF can be obtained by solving the discrete time Riccati equation and the optimal FDF is not unique. A numerical example is given to illustrate the proposed method.
Fault Diagnosis Methods for Dynamic Systems

ZHANG Ping,WANG Guizeng,ZHOU Donghua

DOI: https://doi.org/10.3969/j.issn.1000-8152.2000.02.001

2000-01-01

Abstract:Fault diagnosis in physical systems turn out to become very complex as soon as the considered systems are no longer elementary and become more and more complex and sophisticated, it is then legitimate for companies to acquire an effective diagnosis system. In our research work, we are interested in the diagnosis of industrial hybrid systems, which are composed of continuous systems, discrete event systems and an interface that manages the interactions between the two aspects. The aim of this paper is, first, to give an overview of hybrid systems, and second, to review the state of the art of methods and techniques for fault diagnosis of hybrid systems.
Study of Fault Diagnosis Method for Train Control System

Lu Lu,Xu Zhengguo,Wang Wenhai,Sun Youxian

DOI: https://doi.org/10.13879/j.issn1000-7458.2010.05.022

2010-01-01

Abstract:The safety is one of the most important and fundamental requirements for train operation.As the key technical equipment for train monitoring,control,and scheduling,the reliability of train control systems (TCSs) is directly related to the safety of train operation.Fault diagnosis for TCSs is an important way to guarantee the reliability of TCSs.This paper made a review over TCSs fault diagnosis techniques.First,fault diagnosis methods for TCSs are classified and summarized.Then,some research achievements of TCSs fault prediction were summarized.Finally,some potential directions for future TCSs fault diagnosis research are pointed out.
$$H_{2}$$-Optimization-based Fault Detection for LDTV Systems

Maiying Zhong,Ting Xue,Steven X. Ding,Donghua Zhou

DOI: https://doi.org/10.1007/978-981-19-5438-2_5

2022-01-01

Abstract:$$H_{2}$$ -optimization is a prevalent concept in control theory and is adopted, in its initial form, for optimization issues related to $$H_{2}$$ -norm of transfer functions. Thanks to its optimization interpretation in the context of the well-known linear quadratic Gaussian (LQG) control problem, $$H_{2}$$ -optimization is widely accepted as an established term for optimal control and filtering of linear systems under a quadratic cost function. In this regard, we will, in this chapter, introduce fault detection schemes for LDTV systems. Apart from presenting the standard algorithms, we will focus on gaining deep insights into optimal estimation, residual generation and optimal fault detection issues behind the optimization, and learning alternative interpretations. To this end, some basic estimation and fault detection problems will be, at first, addressed. Although these problems are formulated in the context of static processes, they are helpful to understand the centerpiece of conceptual solutions of any fault detection problems, independent of the system type under consideration. The subsequent study on fault detection in LDTV systems is in fact a natural extension and applications of these solutions, with the aid of advanced system theoretical handlings.
Robust Fault Diagnosis of Linear Systems

CHEN Mao-yin,ZHOU Dong-hua

DOI: https://doi.org/10.3969/j.issn.1000-8152.2005.05.009

2005-01-01

Abstract:The problem of robust fault diagnosis for linear systems is discussed.With the proposed chaos synchronization method,this problem can be transformed into the problem of pole placement or the solution of a linear matrix inequality.The proposed scheme directly reconstructs the fault signal rather than obtaining it by generating and evaluating the residual signals.
A Survey of Fault Diagnosis and Fault-Tolerant Techniques—Part I: Fault Diagnosis With Model-Based and Signal-Based Approaches

Zhiwei Gao,Carlo Cecati,Steven X. Ding

DOI: https://doi.org/10.1109/tie.2015.2417501

IF: 7.7

2015-06-01

IEEE Transactions on Industrial Electronics

Abstract:With the continuous increase in complexity and expense of industrial systems, there is less tolerance for performance degradation, productivity decrease, and safety hazards, which greatly necessitates to detect and identify any kinds of potential abnormalities and faults as early as possible and implement real-time fault-tolerant operation for minimizing performance degradation and avoiding dangerous situations. During the last four decades, fruitful results have been reported about fault diagnosis and fault-tolerant control methods and their applications in a variety of engineering systems. The three-part survey paper aims to give a comprehensive review of real-time fault diagnosis and fault-tolerant control, with particular attention on the results reported in the last decade. In this paper, fault diagnosis approaches and their applications are comprehensively reviewed from model- and signal-based perspectives, respectively.

automation & control systems,engineering, electrical & electronic,instruments & instrumentation
THEORY AND APPLICATIONS OF FAULT TOLERANT CONTROL

ZHOU Donghua,DING X

DOI: https://doi.org/10.16383/j.aas.2000.06.011

2000-01-01

ACTA AUTOMATICA SINICA

Abstract:A survey of fault tolerant control for dynamic systems is presented. The main results in classical fault tolerant control are firstly introduced. Then, emphasis is put on the robust fault tolerant control as well as the fault diagnosis and fault tolerant control of nonlinear systems developed in recent years. Some typical application results of fault tolerant control are discussed, and finally, some open questions are pointed out.
Fault detection of linear discrete-time periodic systems

P. Zhang,S. X. Ding,G. Z. Wang,D. H. Zhou

DOI: https://doi.org/10.1109/TAC.2004.841933

IF: 6.549

2005-01-01

IEEE Transactions on Automatic Control

Abstract:In this note, an approach to the design of optimal fault detection system for linear discrete-time periodic systems is proposed, which leads to an optimized compromise between robustness to unknown disturbances and sensitivity to faults. The needed computation mainly consists in solving a difference periodic Riccati system. The proposed approach is finally illustrated by a numerical example. © 2005 IEEE.
Robust Fault Diagnosis for Linear Time Invariant Uncertain Systems

Jingjing Li,Kemin Zhou,Zhang Ren

DOI: https://doi.org/10.1109/wcica.2008.4593089

2008-01-01

Abstract:This paper aims at developing a systematic approach in frequency domain to design robust fault detection filters for linear time invariant (LTI) systems with model uncertainties. Three types of fault detection (FD) problems, i.e., H-/H-infinity problem, H-2/H-infinity problem and H-infinity/H-infinity problem, are formulated and a procedure for designing the optimal robust fault detection filters is presented.
Residual evaluation of fault detection in discrete‐time systems

Zhihao Zhang,Tong Yao,Weixin Han

DOI: https://doi.org/10.1002/asjc.3293

IF: 2.4

2024-01-08

Asian Journal of Control

Abstract:This paper studies residual evaluation of fault detection in discrete‐time systems considering unknown‐but‐bounded disturbance. By applying Lyapunov stability principle and zonotopic technique, respectively, two dynamic threshold estimation methods are proposed to detect fault of discrete‐time systems. The proposed methods are extended to systems with time‐delay to improve the applicability in practical systems. The effectiveness and comparison of the proposed methods are illustrated by numerical examples.

automation & control systems
Fault Diagnosis for VSC-HVDC Using Wavelet Transform

Sun Xiaoyun,Tong Xiangqian,Yin Jun

DOI: https://doi.org/10.1109/appeec.2012.6307632

2012-01-01

Abstract:VSC-HVDC is a kind of HVDC technology which based on voltage source converter and turn-off devices. Its poor over voltage/current capacity are prone to failure. Based on the established VSC-HVDC system simulation model, the DC voltage waveforms under various fault conditions are achieved, and then the character of system fault is decided according to the amplitude fluctuation range of DC voltage. Moreover, in full consideration of influence of transmission power, the wavelet analysis method is adopted to extract the feature of faulty signal, and combined with artificial neural network the system fault is identified. Simulation results show that this method can diagnose and identify VSC-HVDC fault effectively, and the accuracy is not impacted by transmission power.
A New Scheme of Fault Detection for Linear Discrete Time-Varying Systems.

Maiying Zhong,Steven X. Ding,Donghua Zhou

DOI: https://doi.org/10.1109/tac.2015.2497899

IF: 6.549

2016-01-01

IEEE Transactions on Automatic Control

Abstract:In this note, a new scheme of fault detection (FD) is proposed for linear discrete time-varying (LDTV) systems subject to l(2)-norm bounded unknown inputs. The basic idea is to find an optimal estimation of the l(2)-norm of the unknown inputs including the unknown initial state variables. This leads to a natural design of the FD system with the l(2)-norm boundedness of the unknown inputs as a threshold and the l(2)-norm of the unknown input estimate as the evaluation function. To avoid heavy computational burden, projection technique in Krein space is applied which allows a recursive computation of the evaluation function. It is shown that the achieved FD system satisfies both the worst case and best case sensitivity/robustness ratio criteria and further applications to observer-based FD lead to an alternative design of H-infinity/H-infinity and/or H-/H-infinity fault detection filter.
Fault-Tolerant Control of Networked Control System with Time-Varying Transmission Times

Jun Ren,Chun-Wen Li,De-Zong Zhao

DOI: https://doi.org/10.1109/icmlc.2007.4370205

2007-01-01

Abstract:The problem of fault-tolerant control for a class of networked control system with time-varying transmission times is studied. A generalized-controlled linear discrete model with sensor faults is presented, upon which using Lyapunov method the sufficient conditions for asymptotically stability is given in terms of linear matrix inequalities(LMI), and the law of the controller based on observer are given. Finally, an illustrative example and the simulation results are given to demonstrate the effectiveness of the proposed design method.
Review on Diagnosis Techniques for Intermittent Faults in Dynamic Systems

Donghua Zhou,Yinghong Zhao,Zidong Wang,Xiao He,Ming Gao

DOI: https://doi.org/10.1109/tie.2019.2907500

IF: 7.7

2020-01-01

IEEE Transactions on Industrial Electronics

Abstract:In the past decades, with the rapid development of modern technologies, a special kind of fault, the intermittent fault (IF) has become a serious threat to system securities. Although fruitful research results have been obtained for fault diagnosis, most of them are concerned with permanent faults. Furthermore, up to now, there has been no overview on the diagnosis techniques for IFs in dynamic systems. In fact, IFs are common in a variety of fields, whereas their research is far from mature and many open issues still remain to be solved. Therefore, in this overview, our main objective is to attract direct attentions from more researchers and engineers into the fascinating area of IF diagnosis. In this paper, the concept, research background, challenges and research motivations of IFs are introduced. Then, current research into diagnostics of IFs is reviewed, along with discussions on their strengths, limitations, and future directions.

Fault Diagnosis for Linear Discrete Time-Varying Systems and Its Applications

Delay-dependent fault detection for switched linear systems with time-varying delaysthe average dwell time approach

A survey on model-based fault diagnosis for linear discrete time-varying systems

Technology and Development of Fault Diagnosis Based on Graph Theory

A Variable Moving Window Approach for On-Line Fault Diagnosis in Industrial Processes

Fault Diagnosis and Application to Modern Systems 2018

Optimal Fault Detection for Linear Discrete Time-Varying Systems

Fault Diagnosis Methods for Dynamic Systems

Study of Fault Diagnosis Method for Train Control System

$$H_{2}$$-Optimization-based Fault Detection for LDTV Systems

Robust Fault Diagnosis of Linear Systems

A Survey of Fault Diagnosis and Fault-Tolerant Techniques—Part I: Fault Diagnosis With Model-Based and Signal-Based Approaches

THEORY AND APPLICATIONS OF FAULT TOLERANT CONTROL

Fault detection of linear discrete-time periodic systems

Robust Fault Diagnosis for Linear Time Invariant Uncertain Systems

Residual evaluation of fault detection in discrete‐time systems

Fault Diagnosis for VSC-HVDC Using Wavelet Transform

A New Scheme of Fault Detection for Linear Discrete Time-Varying Systems.

Fault-Tolerant Control of Networked Control System with Time-Varying Transmission Times

Review on Diagnosis Techniques for Intermittent Faults in Dynamic Systems