Abstract:This paper presents fabrication of an ultrasonic regenerative evaporative cooler, coupled with a desiccant dehumidifier. Ultrasonic regenerative evaporative cooler consists of several sets of a dry channel and a wet channel. A part of the air from the dry channel is redirected into the wet channel where it is cooled by evaporation of water mist from an ultrasonic atomiser. Air flowing through dry channels is pre-cooled by heat transfer between wet and dry channels, without changing its humidity. In this cooler, the conventional hygroscopic layer for wetting the plate surface is replaced with the water mist. It is observed that the performance of the cooling system significantly depends on the channel spacing, channel length, inlet airflow rate and extraction ratio, and marginally depends upon feed water temperature. The room cooling capacity is eminently responsive to both air mass flow rate and extraction ratio. The maximum available room cooling capacity of 339.8 W is obtained for the optimal values of 0.0488 kg/s mass flow rate of air and 0.37 extraction ratio. The prototype achieved wet-bulb effectiveness values as high as 1.15 and delivered more than 10°C temperature drop. Practical application: An ultrasonic regenerative evaporative cooler can be coupled with a desiccant dehumidification unit for use in hot and humid climate to achieve comfort condition utilising less energy and feed water when compared to the vapour compression refrigeration system. From this prototype researchers and engineers can develop, by combining desiccant regenerators and evaporative coolers which use ultrasonic method for low-temperature dehydration of desiccant substance. Solar thermal energy can also be directly utilised for marginally heating the desiccant substance during the regeneration process. Overall, this system can contribute to the development of energy efficient buildings.

High‐performance and Wide Relative Humidity Passive Evaporative Cooling Utilizing Atmospheric Water

Capillary Container Array Structures for Efficient, Energy-Saving, and Sustainable Evaporative Cooling and Humidification

STUDY OF AN INNOVATIVE SOLAR DESICCANT COOLING SYSTEM FOR DEHUMIDIFICATION AND CHILLED WATER PRODUCTION

Advanced Material Design and Engineering for Water‐Based Evaporative Cooling

Analysis on Solar Energy Powered Cooling System Based on Desiccant Coated Heat Exchanger Using Metal-Organic Framework

Metal-Organic Frameworks as advanced moisture sorbents for energy-efficient high temperature cooling

Study Of An Innovative Solar Desiccant Cooling System Producing Both Dry Air And Chilled Water

Hydrophilic radiative cooler for direct water condensation in humid weather

Camel‐Fur‐Inspired Graphite‐Based Hygroscopic Membrane for Passive Air Cooling with Ultrahigh Cooling Power (Adv. Energy Mater. 16/2024)

An Adaptive Direct Evaporative Cooler That Regulates the Sub-Ambient Temperature by Controlling the Evaporation Rate

Efficient Passive Cooling Over a Novel Bifunctional Polymer Bilayer Composite Simultaneously Possessing Radiative and Evaporative Cooling Properties

Hybrid Passive Cooling for Power Equipment Enabled by Metal-Organic Framework

Efficient harvesting of renewable evaporative energy from atmospheric air through hierarchical nano/microscale shaping of air-water interface

Photovoltaic cooling and atmospheric water harvesting using a hygroscopic hydrogel

Experimental study of an ultrasonic regenerative evaporative cooler for a desiccant cooling system

Experimental investigation on self-cooled desiccant air conditioning system driven by solar energy

Enhancing the internal thermal conductivity of hydrogel for efficient passive heat dissipation: Experimental study of a surface simulating a cooled photovoltaic panel

Interface chemical coupling enables Janus elastomer-hydrogel composites for a roof-free evaporator with efficient hydrocooling condensation

Lubricated Surface in a Vertical Double-Sided Architecture for Radiative Cooling and Atmospheric Water Harvesting

Photovoltaic Passive Cooling Via Water Vapor Sorption-Evaporation by Hydrogel

A High Heat Dissipation Strategy Based on a Multi-Scale Porous Hydrogel and Heat Sink Exhibiting Cooling Capacity Comparable to That of Forced Air Convection but with Zero Energy Consumption