Abstract:Optimization of the structural and working parameters for a cutting system are essential to improve the working performance and reduce the cutting energy consumption and mechanical damage of the vegetable harvester machinery. An asymmetric root-cutting system was developed to efficiently solve the problems of high cutting loss and energy consumption of mechanized harvesting of Chinese cabbage. Discrete element method (DEM) and microscopic observation were utilized to establish the simulation model of Chinese cabbage, and a delamination particle model was proposed in terms of contact interactions. The experimental methods of Plackett-Burman design (PBD), steepest ascent (SA), and Box Behnken design (BBD) were applied to determine significant factors from eight major influential factors and to optimize the structural and working parameters of the cutting system, and further validated experiments were performed according to the practical feasibility of the optimal combinations of parameters. Finally, the cutting mechanisms were revealed both at a macro and micro level by comparative analyses of the cutting process using EDEM simulation. On this basis, the designed root-cutting device was configured on the self-propelled Chinese cabbage harvester for experimental verification. Results showed that the four most impactful factors on maximum reaction force (MRF) of root-cutting were determined in the order of cutting pitch angle ( D ), cutter speed ( A ), walking speed ( E ), and cutter overlap amount ( B ), and most interactions between interactive factors had consequences for the cutting force change, except A and cutting position ( C ). The minimum value of MRF was 88.62 N when the cutter speed, cutter overlap amount, cutting pitch angle, and walking speed were 186.91 r min −1 , 17.87 mm, 12.26°, and 0.30 m s −1 , respectively. Results of the validated experiments indicated that the measured MRF was 93.41 N under the specified parameters of 187 r min −1 , 18 mm, 12°, and 0.3 m s −1 . This value was found to be comparable to the original value, within an acceptable percentage change of 5.41 %. These findings demonstrate the feasibility of optimizing the cutting system based on DEM. In comparison to the three most prevalent combinations of cutting disks, the cutting system utilizing one concave disk and one sawtooth disk could efficiently sever roots over shorter periods during the cutting process. The combined disks were arranged at an angle of 12° in the longitudinal direction. The forces of each layer of the particle structure inside the root were inconsistent during the root-cutting process. The internal bonding forces of the two-layer particle model played a role as a structural support of the parenchyma in the root epidermis, and the connecting epidermis between the inner and outer epidermis stand greater forces. The result of the field experiment showed that the average productivity of the Chinese cabbage harvester was 0.11 hm 2 h −1 , and the average qualified rate of root-cutting was 93.40 %, which demonstrated that the optimized root-cutting device efficiently fulfills the harvest requirements of high efficiency, and low cutting energy consumption and damage.

Stripping Mechanism and Loss Characteristics of a Stripping-Prior-to-cutting Header for Rice Harvesting Based on CFD-DEM Simulations and Bench Experiments

Diverse-velocity Threshing Device with Double-axletree Flow

Optimisation and Finite Element Simulation of the Chopping Process for Chopper Sugarcane Harvesting

Study on Performance of Concentric Threshing Device with Multi-Threshing Gaps for Rice Combines

Optimization of a Whole-Stalk Operating System after Sugarcane Base Cutting

DISCRETE ELEMENT METHOD (EDEM) SIMULATION AND PARAMETER OPTIMIZATION: DESIGN AND TESTING OF A LOW-LOSS AND HIGH-EFFICIENCY CORN THRESHING DEVICE

DESIGN AND EXPERIMENTAL STUDY OF FLEXIBLE THRESHING DEVICE FOR LONGITUDINAL AXIAL FLOW CORN

Simulation and Optimization Experiment: Working Process of a Cleaning Device for Flax Combine Harvester

Optimization of airflow cylinder sieve for threshed rice separation using CFD-DEM

Design and Performance Test of Rotary Grate Concave Threshing and Separating Unit of Head-Feeding Combine Harvester

Optimization of cutting position and mode for cabbage harvesting

Optimization and validation of root-cutting device for Chinese cabbage harvester based on discrete element method

Numerical simulation and field tests of minimum-tillage planter with straw smashing and strip laying based on EDEM software

DESIGN AND EXPERIMENT OF TRANSVERSE AXIAL FLOW CORN FLEXIBLE THRESHING DEVICE

Design and test of smashing and scattering device of double-channel feeding ratoon rice harvester

Performance Evaluation of a Chopper System for Sugarcane Harvester

The impact of 'T'-shaped furrow opener of no-tillage seeder on straw and soil based on discrete element method

Design, Simulation, and Test of a New Threshing Cylinder for High Moisture Content Corn

Analysis and Test of Splitting Failure in the Cutting Process of Cabbage Root

Design and Experimentation of the Millet Combine Harvester Header