Abstract:Abstract This paper presents 3D Fabry–Pérot (FP) cavities fabricated directly onto cleaved ends of low-loss optical fibers by a two-photon polymerization (2PP) process. This fabrication technique is quick, simple, and inexpensive compared to planar microfabrication processes, which enables rapid prototyping and the ability to adapt to new requirements. These devices also utilize true 3D design freedom, facilitating the realization of microscale optical elements with challenging geometries. Three different device types were fabricated and evaluated: an unreleased single-cavity device, a released dual-cavity device, and a released hemispherical mirror dual-cavity device. Each iteration improved the quality of the FP cavity’s reflection spectrum. The unreleased device demonstrated an extinction ratio around 1.90, the released device achieved 61, and the hemispherical device achieved 253, providing a strong signal to observe changes in the free spectral range of the device’s reflection response. The reflectance of the photopolymer was also estimated to be between 0.2 and 0.3 over the spectrum of interest. The dual-cavity devices include both an open cavity, which can interact with an interstitial medium, and a second solid cavity, which provides a static reference reflection. The hemispherical dual-cavity device further improves the quality of the reflection signal with a more consistent resonance, and reduced sensitivity to misalignment. These advanced features, which are very challenging to realize with traditional planar microfabrication techniques, are fabricated in a single patterning step. The usability of these FP cavities as thermal radiation sensors with excellent linear response and sensitivity over a broad range of temperature is reported. The 3D structuring capability the 2PP process has enabled the creation of a suspended FP heat sensor that exhibited linear response over the temperature range of 20 oC –120 oC; temperature sensitivity of ∼50 pm oC −1 at around 1550 nm wavelength; and sensitivity improvement of better than 9x of the solidly-mounted sensors.

In Situ Thermal Characterisation and Filamentary Modification in Polymethylpentene

Three-dimensional Fabry–Pérot cavities sculpted on fiber tips using a multiphoton polymerization process

Fabrication of and Ultraviolet Lasing in TPE/PMMA Polymer Nanowires

Optical Microstructures Fabricated by Femtosecond Laser Two-Photon Polymerization

Theoretical and experimental investigations of photo-sensitivity and polarization-sensitivity in TI/PMMA polymers

An experimental study of intensity‐phase characterization of femtosecond laser pulses propagated through a polymethyl methacrylate

Polaron lifetime enhancement of P3HT thin film under femtosecond laser irradiation and its ultrafast mechanism

In Situ Characterization of Thermal‐Induced Evolution of Structure/Optical Properties of Heterogeneous 3D Chiral Soft Photonic Crystal Polymer

Thermally resettable laser transmission induced transparency in polymer waveguides at 635 nm

Stable Single‐Mode Lasing from a Hybrid Perovskite–Polymer Fiber

Nanoscale local modification of PMMA refractive index by tip-enhanced femtosecond pulsed laser irradiation

Controlled photothermal ablative processing of commercial polymers minimizing undesired thermal effects under high frequency femtosecond laser irradiation

Nonlinear Saturable Absorption of Nanoscaled Bi2te3/Pmma Composite Film

Tuning the optical properties of polydimethylsiloxane films and fabricating elastic volume Bragg diffraction gratings by picosecond ultraviolet Laser-induced photochemical reactions

Compressing High Energy Lasers through Optical Polymer Films

Hybrid Wavelength Manipulation with Enhanced Ambient-Thermal Adaptability in an All-Polarization-Maintaining Mode-Locked Fiber Laser

Temperature Field-Assisted Ultraviolet Nanosecond Pulse Laser Processing of Polyethylene Terephthalate (PET) Film

Advancing large-scale thin-film PPLN nonlinear photonics with segmented tunable micro-heaters

Near‐infrared Light‐Induced Polymerizations: Mechanisms and Applications

Femtosecond laser micro-structuring of amorphous polyether(ether)ketone at 775 nm and 387 nm

Ultrafast Polarization‐Maintaining Fiber Lasers: Design, Fabrication, Performance, and Applications