Abstract:Summary form only given. Capillary discharge plasmas have been widely used as electrothermal chemical (ETC) launch devices, fusion reactor pellet injectors and high heat flux sources for material studies. In the electro thermal chemical launcher, the mechanisms of the plasma-propellant interaction are critical, with many factors being of potential importance. In particular, the role of plasma radiation is disputed. We will report the effect of three different metal ions and radiation in the capillary discharge plasma on the plasma-propellant interactions. Conventionally, a capillary initiated by a metal wire of about 2 mg and with an ablative liner material (e.g. polyethylene) is used as the plasma generator. The plasma is mainly composed of CO, H + , C, etc. The proportion of metal ions was negligible. We have designed a new capillary discharge plasma generator with different metal powders of higher weight as the initiators. The performance of the new generator is compared with the traditional one through an open-air test. A spectrometer and ICCD were used to measure the surface temperature of the propellants while a CCD was used to visualize the plasma jet. The combustion tests were conducted in a transparent closed vessel, making it possible to measure the plasma parameters at the propellant surface and observe the combustion process in the closed vessel. A fused silica window was placed between the plasma and propellants to ensure that the propellant could only be affected by plasma radiation. The burning rate and the p-t curve were obtained in the tests and the combustion products were analyzed by a mass spectrometer. Interrupted burning tests were also carried out to acquire information about the surface of the propellants at different burning stages. In order to perform accurate modeling of the plasma-propellant interaction, we have also developed a two-dimensional time-dependent capillary discharge model based on a modified ablation model. In our model, special attention is paid to the radial distribution of the capillary discharge plasma characteristics. To investigate the factors that influence the radial distribution, the radial transport of the ablation products is taken into consideration. Further, the competition between the ablation and deposition process with time in the capillary discharge is also studied. The aim of our study are to provide results that will assist the design of new propellants and new plasma generators for the ETC launcher.

Experimental Study of Millisecond Repetitive Capillary Discharge Plasma Characteristics for Simulating ITER-Like Transient Heat Load

Transient Heat Thermal Load Characteristics Produced by a Three-Electrode Capillary Discharge Generator

Toward a First-Principles Integrated Simulation of Tokamak Edge Plasmas

Development of a Repetitive Plasma Source for Simulation of Mitigated Edge Localized Mode Transient Heat Load

A Repetitive High Current Pulse Generator for High Flux Electrothermal Plasma Jets

Power Balance Investigation in Long-Pulse High-Performance Discharges with ITER-like Tungsten Divertor on EAST

Investigation of pulse plasma reactor discharge characteristics

Roles of Metal Ions and Plasma Radiation in the Interactions Between A Capillary Discharge Plasma and Propellants

Integrated Operating Scenario to Achieve 100-Second, High Electron Temperature Discharge on East

Impact of repetitive ELM transients on ITER divertor tungsten monoblock top surfaces

Progress of Physics Understanding for Long Pulse High-Performance Plasmas on EAST Towards the Steady-State Operation of ITER and CFETR

Theoretical Simulation of Thermal Behavior in Transient Heat Loads Testing of Plasma-Facing Materials

Pulsed Discharge Characteristics of a Semicombustible Plasma Generator for ETC Launchers

A Metal-Wall Compatible High-Confinement Tokamak Plasma Regime for Fusion Energy

Prediction of pellet mass thresholds for ELM triggering in low-collisionality, ITER-like discharges

Modeling 3D Plasma Boundary Corrugation and Tailoring Toroidal Torque Profiles with Resonant Magnetic Perturbation Fields in ITER

Investigation of ELM-related Larmor ion flux into toroidal gaps of divertor target plates

Compatibility of divertor detachment and ELM suppression in DIII-D high-βp plasmas with ITER-similar shape

Study of Different Models of the Wall Ablation Process in Capillary Discharge

Evaluation of Performance for the East Upgraded Divertor Targets During Type I Elmy H-Mode