Abstract:Recently, sodium ion batteries (NIBs) gained increasing attention, because of its abundant reserves and relatively even geological distribution. However, the development of NIBs is greatly hampered because of the lack of appropriate active materials for both cathodes and anodes. Since the Na ion is ca. 55% larger than the Li ion, finding suitable host materials with sufficiently large interstitial space to accommodate sodium ions and to allow reversible and rapid ion insertion and extraction is very difficult. NASICON-type Na3V2(PO4)3 has recently been considered as a prospective cathode material for NIBs, because of its highly covalent 3D framework crystalline structure, high energy density (~400 Wh/kg) and good thermal stability. For anode materials, disordered carbon is particularly attractive because of their large interlayer distance and disordered structure that could accommodate sodium ions. Here, we briefly present porous carbon based electrodes for NIBs with excellent rate performance: (1) Carbon-coated nanosized Na3V2(PO4)3 embedded in the porous carbon matrix (abbreviated as CC-NVP@PCM); (2) Nitrogen-doped activated porous carbon fibers (ACFs); (3)Flexible free-standing porous carbon nanofibers (P-CNFs) with three-dimensional (3D) interconnected structure. The CC-NVP@PCM was prepared by using a facile soft-chemistry based method with post heat-treatment. It shows high rate performance (44 mAhg-1at 200C ). This ultrahigh rate performance is comparable to that of supercapacitor, but with much higher energy density. The ACFs were synthesized by pyrolysis of Ppy nanofiber precursor. It shows excellent capacity retention and extraordinary rate performance. The reversible capacity at 0.05 Ag-1 is 296 mAhg-1 and could still maintain as 72 mAg-1 at a current of 10 Ag-1. In case of the P-CNFs electrode prepared by electrospinning, it delivers a reversible capacity of 266 mAh.g-1 after 100 cycles at 0.2C, corresponding to 80.3 % of the initial charge capacity. When cycled at a current density as high as 500 mAg-1 (2C), it still delivers a reversible capacity of ~140 mAh.g-1after 1000 cycles. The improvement of electrochemical performance of these porous carbon based electrodes for NIBs is attributed to the special design and porous structure, which confined a variety of advantages: hierarchical porous channels enabling short transport length for ions and electrons, carbon coated structure resulting in low resistances, good mechanical properties leading to the excellent morphology stability.

Self-Assembled Nanostructures of Pdi-Bolaamphiphiles As Anode Materials for Advanced Rechargeable Na-Ion Batteries

Enhanced Silicon Diphosphide-Carbon Composite Anode for Long-Cycle, High-Efficient Sodium Ion Batteries

A Hierarchical N/S‐Codoped Carbon Anode Fabricated Facilely from Cellulose/Polyaniline Microspheres for High‐Performance Sodium‐Ion Batteries

Electrode Materials: A Hierarchical N/S-Codoped Carbon Anode Fabricated Facilely from Cellulose/Polyaniline Microspheres for High-Performance Sodium-Ion Batteries (Adv. Energy Mater. 6/2016)

Rayleigh-Instability-Induced Bismuth Nanorod@Nitrogen-Doped Carbon Nanotubes As A Long Cycling and High Rate Anode for Sodium-Ion Batteries

Bipolar Organic Cathodes for Stable and Sustainable Na‐Ion and Rechargeable Al Batteries

A Poriferous Nanoflake-Assembled Flower-Like Ni <sub>5</sub> P <sub>4</sub> Anode for High-Performance Sodium-Ion Batteries

In Situ Precipitated Organic Nanorod Electrodes for Sodium Ion Batteries

Roll-to-roll fabrication of organic nanorod electrodes for sodium ion batteries

Electrodes for Sodium-Ion Batteries with Excellent Rate Performance Using Porous Carbon Networks

A Poriferous Nanoflake-Assembled Flower-Like Ni5P4 Anode for High-Performance Sodium-Ion Batteries

Green and stable organic polymer anode for high rate and fast charge sodium based dual‐ion battery

Molecular grafting towards high-fraction active nanodots implanted in N-doped carbon for sodium dual-ion batteries

Pomegranate-like structured Nb2O5/Carbon@N-doped carbon composites as ultrastable anode for advanced sodium/potassium-ion batteries

Tailoring Alternating Heteroepitaxial Nanostructures in Na-ion Layered Oxide Cathodes Via an In-Situ Composition Modulation Route

Design of Three-Dimensional Metallic Biphenylene Networks for Na-Ion Battery Anodes with a Record High Capacity

Facile Synthesis of Nickel Phosphide @ N-Doped Carbon Nanorods with Exceptional Cycling Stability as Li-Ion and Na-Ion Battery Anode Material

Double-shell and hierarchical porous nitrogen-doped carbon nanocages as superior anode material for advanced sodium-ion batteries

Ultra-Stable, Ultra-Long-Lifespan and Ultra-High-Rate Na-ion Batteries Using Small-Molecule Organic Cathodes

Porous bipolar polymers as organic cathodes for sustainable sodium/potassium-ion batteries

A Low Redox Potential and Long Life Organic Anode Material for Sodium-Ion Batteries