Abstract:In this paper, a model of flood area display and damageevaluation is discussed, which adopts seed spread algorithm to calculate and visualize flood area based on a DEM data set and under the condition of a given water level of flood. The raster image containing flood area is overlaid with raster data converted from thematic vector maps such as land-use map and related to other socio-economic data, and then quantitative evaluation of flood damage is achieved. There are two different cases, the so-called “non-source flood” and “source flood”, for determining flood area based on DEM and under the given water level condition. Non-source flood corresponds to the case with well-distributed and large-area rainfall where all the low-lying land may have a flood disaster, and in this case all the points with elevations below the given water level should be included in the flood area. The “source flood” is the case of flood (e.g. from bank burst) flushing through the surrounding lands that needs to consider “ci rculating” condition. Because flood may be obstructed by ring structures or high lands, thus it can only cover the place where it flows and reaches. One of the computer processing methods suitable for source flood is the seed-spread algorithm. The principle of this method is to select a representative pixel as a seed and to examine its contiguous pixels outward along 4 or 8 directions. The pixels, contiguous to it and meeting the given conditions, become seeds, and then contiguous pixels to the new seeds will be examined in the same way. This process repeats until an aggregation of the pixels which meet the given conditions on a certain plane are obtained. Adopting seed spread algorithm for source-flood area calculation is just to achieve an aggregation of pixels, which satisfies the connectivity requirement and the given conditions of water level. The initial position of seed pixel should usually be selected on the characteristic points, e.g. adjacent to a reservoir dam or stream boundary. The precision of flood area calculation is mainly determined by spatial resolution of the DEM, the area on the ground is represented by each pixel; whereas the accuracy of flood area calculation, to a great extent, is dependent on the preci sion of the DEM's pixel value or elevation.Once the area below the flood water level has been calculated, the flood damage evaluation can be calculated by overlaying the flood range with thematic maps and by relating to other socio-economic data. All thematic maps were converted to raster data because algorithm of the overlay analysis implemented in raster format is relatively simple and computing is fast. In order to improve accuracy of the flood damage evaluation it is necessary to accurately register and georefer all raster layers before overlay analysis. The calculation results of flood damage evaluation are generally represented by tabulation, which is a kind of classified statistics of flood damage data, e.g. a table representing total area of every land-use type in different administrative divisions. The results of flood area calculation and damage evaluation can also be visually and dynamically provided in the forms of graph, image, 3D or virtual reality. The model has been successfully applied in the “Zhejiang Provincial Water Conservancy Management System” developed for a national project.

Ex-post evaluation analysis of flood control engineering system based on grey relation projection method

A MODEL OF MULTI-OBJECTIVE COMPREHENSIVE EVALUATION FOR POWER PLANT PROJECTS

Comprehensive evaluation model for normal water level scheme based on GIS and grey correlation analysis

Multi-level fuzzy comprehensive evaluation on environmental impact from water control project

Comprehensive Evaluation of Ecological Effect of Hydropower Projects Based on Fuzzy Logic

A GIS-based Method for Flooded Area Calculation and Damage Evaluation

A GIS Based Model for Calculating of Flood Area

Evaluation Index System for Ecological and Environmental Impact of Rural Hydropower Based on PSR Model

Enhancing Flood Risk Assessment and Mitigation Through Numerical Modeling: A Case Study

Multi-Attribute Comprehensive Evaluation Method for Power Transmission and Transformation Projects

Comprehensive benefit of flood resources utilization through dynamic successive fuzzy evaluation model: A case study

GIS-based fuzzy comprehensive evaluation of urban flooding risk with socioeconomic index system development

Optimization of the integrated green-gray-blue system to deal with urban flood under multi-objective decision-making

Urban Flood Resilience Evaluation Based on Heterogeneous Data and Group Decision-Making

Coupled Model of Variable Fuzzy Sets and the Analytic Hierarchy Process and its Application to the Social and Environmental Impact Evaluation of Dam Breaks

Fuzzy Evaluation Model of Risk and Benefit of Flood Resources Utilization Based on Entropy Weight

A novel integrated urban flood risk assessment approach based on one-two dimensional coupled hydrodynamic model and improved projection pursuit method

Extreme Flood Disasters: Comprehensive Impact and Assessment

Design and application of the flood loss evaluation system based on GIS and RS.

Comprehensive Evaluation of Flood and Flood in the Yellow River Basin Based on Gray Correlation Analysis

Grey Comprehensive Evaluation on the Construction Engineering's Green Construction Level Based on Combinational Weight