Abstract:Objective To investigate the influence of displacement of femoral and tibial components on the biomechanics of femoral or tibial bone in coronal view.Methods A series of CT and MRI of the left knee joint of a Han male volunteer was taken and a three-dimensional finite element model of the healthy knee joint was established.The femoral component and the tibial component were designed with varus 6°,varus 3°,0°,valgus 3°,and valgus 6°,and were combined into 25 three-dimensional finite element model (FEM) of medial unicompartmental knee arthroplasty.A 1 000 N load was applied along the femoral mechanical axis.The von Mises cloud stress distribution was observed.Moreover,the lateral compartment load ratio,the high contact stress of cancellous bone and medial cortical bone below the tibial component,the upper surface of the polyethylene liner,and the femoral cartilage in the lateral compartment was measured.The statistically significant indicators compared with the neutral position (0° varus or valgus of the tibia and the femoral prosthesis,and 5° posterior slope of tibia prosthesis) were identified by scatter plots to find the dense and sparse areas of point items.The optimal position of the femoral component and the tibial component was determined by the number of items with statistical significance in the sparse area.Results When the femoral component was placed at 0° position,there was no significant difference in the high contact stress of cancellous bone below the tibial component in the five groups.When the femoral component was placed at 0° position,the tibial component was 6° varus or 6° valgus and the stress was increased by 9.21±3.38 MPa and 9.08±4.13 MPa (P＜0.05),respectively.With the changes of femoral and tibial components from 6° varus to 6° valgus,the high contact stress of the medial cortical bone below the tibia was gradually decreased (P＜ 0.05).When the femoral component was placed at 0°,the tibial component changes from 6° varus to 6° valgus without significant difference in the high contact stress on the upper surface of each group of polyethylene gasket.Compared with the neutral position group,the high contact stress of the 6° varus or 6° valgus group were increased by 2.88±2.53 MPa and 3.47±2.86 MPa,respectively (P＜0.05).The lateral compartment load ratio and the high contact stress of lateral compartment femoral cartilage was gradually decreased (P＜0.05),when the femoral and tibial components changed from 6° varus to 6° valgus.The number (2.8％,1/36) of indicators in the sparse area (the combination of all combinations of femur or tibia from 3° varus to 3° valgus) was less than that (57.8％,37/64) in the dense area (set of all combinations except sparse area),and the difference was significant (x2=29.61,P＜ 0.001).Conclusion It is suggested that the position of the femoral component and the tibial component in fixed medial unicom partmental arthroplasty should not exceed 3° varus or valgus in patients with standard lower limb alignment.

Computational Evaluation of the Axis-Blade Angle for Measurements of Implant Positions in Trochanteric Hip Fractures: A Finite Element Analysis

A novel angle on helical blade placement in trochanteric fractures - The axis-blade angle

Theoretical analysis of changes in femoral stresses after total hip arthroplasty]

Finite element analysis on the position of the spiral blade in the femoral head of internal fixation for intertrochanteric fractures

Biomechanical Evaluation of Three Implants for Treating Unstable Femoral Intertrochanteric Fractures: Finite Element Analysis in Axial, Bending and Torsion Loads

Biomechanical evaluation of two modified intramedullary fixation system for treating unstable femoral neck fractures: A finite element analysis

Positive Medial Cortical Support versus Anatomical Reduction for Trochanteric Hip Fractures: Finite Element Analysis and Biomechanical Testing

Biomechanical comparison of five cannulated screw fixation strategies for young vertical femoral neck fractures

Semi-automated finite element analyses of surgically treated acetabular fractures to investigate the biomechanical behaviour of patient-specific compared to conventional implants

Finite Element Analysis of Optimization on Placement of Medial Fixed-Bearing Unicompartmental Knee Arthroplasty

Intraoperative estimation of natural femoral anteversion from proximal femoral osseous orientation during total hip arthroplasty

Finite element analysis of fixation stability according to reduction position for internal fixation of intertrochanteric fractures

The importance of intramedullary hip nail positioning during implantation for stable pertrochanteric fractures: biomechanical analysis

[Three-Dimensional Finite Element Analysis on Mechanical Behavior of the Bone Remodeling and Bone Integration Between the Bone-Implant Interface after Hip Replacement].

Biomechanical study of extramedullary and intramedullary fixation in the treatment of unstable intertrochanteric reversed-tilt fractures of the femur

Relative Instability Ratios of Bone Wall Defects in Trochanteric Hip Fractures: A Finite Element Analysis

Functional Acetabular Component Positioning During Direct Anterior Approach Hip Arthroplasty Using a Novel Three-Dimensional Virtual Mesh Imaging System With Fluoroscopy

A Biomechanical Comparison of Two Intramedullary Implants for Subtrochanteric Fracture in Two Healing Stages: A Finite Element Analysis

Variability of the femoral mechanical-anatomical axis angle and its implications in primary and revision total knee arthroplasty

Comparison of three different internal fixation implants in treatment of femoral neck fracture—a finite element analysis

Biomechanical evaluation of total ankle arthroplasty. Part II: Influence of loading and fixation design on tibial bone-implant interaction