Abstract:Preprocessing of pharmaceutical powders is a common procedure to condition the materials for a better manufacturing performance. However, such operations may induce undesired material properties modifications when conditioning particle size through milling, for example. Modification of both surface and bulk material structure will change the material properties, thus affecting the processability of the powder. Hence it is essential to control the material transformations that occur during milling. Topographical and mechanical changes in surface properties can be a preliminary indication of further material transformations. Therefore a surface evaluation of the α-lactose monohydrate after short and prolonged milling times has been performed. Unprocessed α-lactose monohydrate and spray dried lactose were evaluated in parallel to the milled samples as reference examples of the crystalline and amorphous lactose structure. Morphological differences between unprocessed α-lactose, 1 h and 20 h milled lactose and spray dried lactose were detected from SEM and AFM images. Additionally, AFM was used to simultaneously characterize particle surface amorphicity by measuring energy dissipation. Extensive surface amorphicity was detected after 1 h of milling while prolonged milling times showed only a moderate particle surface amorphisation. Bulk material characterization performed with DSC indicated a partial amorphicity for the 1 h milled lactose and a fully amorphous thermal profile for the 20 h milled lactose. The temperature profiles however, were shifted somewhat in the comparison to the amorphous reference, particularly after extended milling, suggesting a different amorphous state compared to the spray-dried material. Water loss during milling was measured with TGA, showing lower water content for the lactose amorphized through milling compared to spray dried amorphous lactose. The combined results suggest a surface-bulk propagation of the amorphicity during milling in combination with a different amorphous structural conformation to that of the amorphous spray dried lactose. The hardened surface may be due to either surface crystallization of lactose or to formation of a low-water glass transition.

How Do Morphological Changes of Caffeine Hydrate Influence Caking

Effect of Trehalose Dehydration on Crystal Morphology and Food Caking During Post-Treatment

Amorphous and Humidity Caking: A Review

Caking of Crystals: Characterization, Mechanisms and Prevention

Rapid Evaluating Caking Tendency of Nonspherical Crystals by Developing a Shape-Based Crystal Bridge Growth Model

Temperature- and Ph-Dependent Morphology and Ft-Ir Analysis of Magnesium Carbonate Hydrates

Study on the caking behavior of anhydrous citric acid

Effect of Drying Method on Calcium Silicate Hydrate (C-S-H): Experiments and Molecular Dynamics Simulations Study

Drug-Induced Phase Transition from Cubic Phase to Vesicle

Investigation of the Morphology of Secondary Nucleation of Hydrate from a Water Droplet in Liquid Cyclopentane

Moisture Sorption Behaviour, Microstructural Changes and Macroscopic Deformation of Hardened Cement Pastes During the First Three Drying–resaturation Cycles

Milling induced amorphisation and recrystallization of α-lactose monohydrate

Insight into Morphology Change of Chitin Microspheres Using Tertiary Butyl Alcohol/H2 O Binary System Freeze-Drying Method.

The Time and Location Dependent Prediction of Crystal Caking by a Modified Crystal Bridge Growth Model and DEM Simulation Considering Particle Size and Shape

Hydration Mechanism and Kinetic Response of a C4A3$-C2S Binary System

Modulation of ice crystal formation behavior in pectin-sucrose hydrogel by freezing temperature: Effect on ice crystal morphology and drying properties

Formation and Transformation Behavior of Sodium Dehydroacetate Hydrates

Effect of Temperature on the Hydration Process of Hemihydrate Calcium Sulfate Whiskers

Statistical analysis of the drying pattern of coffee

Effect of Annealing on Morphologies and Performances of Hydroxypropyl Methylcellulose/hydroxypropyl Starch Blends

Model-based Design for Water-Soluble Crystals with Anti-Caking Function by the Feedback Between Caking Prediction and Crystallization Control