Abstract:High energy density solid-state batteries require high areal loading composite cathodes (>4 mAh/cm 2 ). However, increasing the cathode loading or thickness can introduce additional challenges apart from the expected rate capability limitations, which are much less pronounced in low loading or thin composite cathodes. These include greater volume changes during cycling at the cell level, which can introduce stresses at the various interfaces. While there are many successful reports showing long-term stable cycling of high loading composite cathode in all-inorganic solid-state cells, these cells are typically cycled under high pressures (>10 MPa), which may be impractical to commercialize. Such high pressures can alleviate the interfacial contact loss issues generated due to volume changes during cycling. Polymer electrolytes are non-rigid and can potentially accommodate strains to maintain contact at the interfaces during cycling, given sufficient adhesion. In this work, we will show some of the design strategies that were implemented to alleviate the contact loss issue at the polymer electrolyte separator/composite cathode interface in order to achieve stable cycling with thick polymer electrolyte-based composite cathodes in coil-cell configuration. Nickel-rich NMC (LiNi x Mn y Co z O 2 ) cathodes (NMC811 or 622) were used as the active materials. Since polymer electrolytes are known to be unstable with high voltage cathodes such as NMCs, the contribution of oxidative instability to the overall capacity decay will also be discussed by comparing two polymer electrolytes with different oxidative stability (a PEO-based dual-ion polymer electrolyte, and a single-ion polymer electrolyte). This research was sponsored by the U.S. Department of Energy (DOE), Office of Energy Efficiency and Renewable Energy for the Vehicle Technologies Office’s Advanced Battery Materials Research Program (Simon Thompson, Program Manager). A part of this research was sponsored by the Laboratory Directed Research and Development Program of Oak Ridge National Laboratory (ORNL), managed by UT-Battelle, LLC for the U.S. Department of Energy under Contract No. DE-AC05-00OR22725. The SEM in this work was performed and supported at the Center for Nanophase Materials Sciences in Oak Ridge National Lab, a DOE Office of Science user facility.

Boosting Cycling Stability of Polymer Sodium Battery by “Rigid-Flexible” Coupled Interfacial Stress Modulation

Cathodic Stress Modulation with Stable Interfaces for High-Performance Polymer Solid-State Sodium-Metal Batteries

An In-Situ Synergistic Enhancement Strategy from G-C3n4 and PDOL Composite Solid Electrolyte on the Interface Stability of Solid-State Lithium Battery

A strategy involving the use of 3D self-supporting B.N co-doped carbon nanofiber composite solid polymer electrolytes to stabilize the interface of Polymer electrolyte and lithium-metal

Molecule Crowding Strategy in Polymer Electrolytes Inducing Stable Interfaces for All‐Solid‐State Lithium Batteries

Enabling Scalable Polymer Electrolyte with Dual-Reinforced Stable Interface for 4.5 V Lithium-Metal Batteries.

Designing Solvated Double-Layer Polymer Electrolytes with Molecular Interactions Mediated Stable Interfaces for Sodium Ion Batteries

Interfacial Plasticization Strategy Enabling a Long-Cycle-Life Solid-State Lithium Metal Battery

Mitigating interfacial instability of high-voltage sodium layered oxide cathodes with coordinative polymeric structure

Rigid and flexible dual-network polymer electrolytes with enhanced interfacial interaction to accelerate Li+ transfer

Durable and Adjustable Interfacial Engineering of Polymeric Electrolytes for Both Stable Ni-Rich Cathodes and High-Energy Metal Anodes

Rigid-tough Coupling of the Solid Electrolyte Interphase Towards Long-Life Lithium Metal Batteries

Taichi-inspired Rigid-Flexible Coupling Cellulose-Supported Solid Polymer Electrolyte for High-Performance Lithium Batteries

Boosting Selective Na+ Migration Kinetics in Structuring Composite Polymer Electrolyte Realizes Ultrastable All‐Solid‐State Sodium Batteries

High Cycling Stability for Solid‐State Li Metal Batteries via Regulating Solvation Effect in Poly(Vinylidene Fluoride)‐Based Electrolytes

Rational design of a topological polymeric solid electrolyte for high-performance all-solid-state alkali metal batteries

Integrating Polymer Electrolytes-Based Thick Composite Cathodes in All-Polymer Solid-State Lithium Metal Batteries

A rigid-flexible coupling poly(vinylene carbonate) based cross-linked network: A versatile polymer platform for solid-state polymer lithium batteries

Enhancing interfacial stability in solid-state lithium batteries with polymer/garnet solid electrolyte and composite cathode framework

Making Plasticized Polymer Electrolytes Stable Against Sodium Metal for High‐Energy Solid‐State Sodium Batteries

Solid Polymer Electrolytes with Dual Salts Enhance Lithium-Metal Interfacial Stability for Long Cycle Performance of Lithium Batteries