Abstract:The aim of this study was to analyze the biomechanics in an implant/tooth-supported system under different occlusal forces with rigid/non-rigid connectors by adopting a 3D non-linear finite element (FE) approach. A 3D FE model containing one Frialit-2 implant splinted to the mandibular second premolar was constructed. Contact elements (frictional surface) were used to simulate the realistic interface condition within the implant system and the sliding keyway stress-breaker function. The stress distributions in the splinting system and dissimilar mobility between natural tooth and implant with rigid and non-rigid connectors were observed for six loading types. The simulated results indicated that the lateral occlusal forces significantly increased the implant (sigma(I, max)), alveolar bone (sigma(AB, max)) and prosthesis (sigma(P, max)) stress values when compared with the axial occlusal forces. The sigma(I, max) and sigma(AB, max) values did not exhibit significant differences regardless of the connector type used. However, the sigma(P, max) values with a non-rigid connection increased more than two times those of the rigid connection. The sigma(I, max), sigma(AB, max) and sigma(P, max) stress values were significantly reduced in centric or lateral contact situations once the occlusal forces on the pontic were decreased. Moreover, the vertical-tooth-to-implant displacement ratios with a non-rigid connection were 23 and 9.9 times that for axial and lateral loads, respectively, applied on the premolar. However, the compensated non-rigid connector capabilities were not significant when occlusal forces acted on the complete prosthesis. The non-rigid connector (keyway device) only significantly exploited its function when the occlusal forces acted on a natural tooth. Minimizing the occlusal loading force on the pontic area through occlusal adjustment procedures to redistribute stress in the maximum intercuspation or lateral working position for an implant/tooth-supported prosthesis is recommended.

Biomechanical Evaluation of Bridge Span with Three Implant Abutment Designs and Two Connectors for Tooth-Implant Supported Prosthesis: A Finite Element Analysis

Biomechanical Analysis of Rigid and Non-Rigid Connection with Implant Abutment Designs for Tooth-Implant Supported Prosthesis: A Finite Element Analysis

Three Dimensional Finite Element Stress Analysis on Superstructure of the Fixed Bridge Supported by Tooth-Implant

Analysis of stress distribution of implant-tooth-supported fixed bridge for different pontic lengths

Numerical simulation on the biomechanical interactions of tooth/implant-supported system under various occlusal forces with rigid/non-rigid connections

The analysis of stress distribution of the natural tooth-implant supported fixed bridge for different pontic length

Mechanical effects on abutments with different fixed bridge designs replacing lower lateral incisor

The effect of mandibular flexure on the design of implant-supported fixed restorations of different facial types under two loading conditions by three-dimensional finite element analysis

The Biomechanical Analysis of The Long Rigid Fixed Bridger

Influence of Implant Cantilever Length on Stress Distribution: A Finite Element Analysis

Biomechanical Effects of Different Load Cases with an Implant-Supported Full Bridge on Four Implants in an Edentulous Mandible: A Three-Dimensional Finite Element Analysis (3D-FEA)

Influence of Different Abutment Designs on the Biomechanical Behavior of Dental Root-Analog Implant

Stress Distribution on Abutment of Tooth- Implant Fixed Bridge Under Different Loading

Effect of Implant-Abutment Connection and Abutment Angulations on Peri-implant Stress Levels: A Finite Element Analysis Study

Stress distribution and displacement of abutment of middle implant-natural teeth fixed bridge under different loading

Effects of different abutment connection designs on the stress distribution around five different implants: a 3-dimensional finite element analysis

Stress Analysis of Endodontically Treated Tooth-Implant Different Connectors Designs in Maxillary Posterior Region: A Finite Element Analysis

A Three-dimensional Finite Element Analysis of the Correlation Between Lengths and Diameters of the Implants of Fixed Bridges with Proper Stress Distribution

Biomechanical Analysis of the Stress Distribution of Rigid Fixed Bridge During Different Thickness of Periodontal Membranes Around Abutments

Nonlinear Finite Element Analysis of Three Implant–abutment Interface Designs

Biomechanical finite element analysis of short-implant-supported, 3-unit, fixed CAD/CAM prostheses in the posterior mandible