Abstract:The present work systematically investigates the effect of cavitator mounting strut and cavitator shape on the ventilation demand to form and sustain a ventilated supercavity under different flow conditions. Three cavitators of different shapes (i.e. 2D cavitators including triangle and disk shape, and 3D cone-shaped cavitator) with the same frontal area are employed for the experiments. The cavitator is connected to a ventilation pipe extended upstream from a mounting strut, referred to as forward-facing model (FFM). The minimal ventilation coefficients to generate (<math>CQf</math>) and to collapse (<math>CQc</math>) a supercavity are measured over a wide range of Froude number (<math>Fr</math>) for each cavitator. Images of overall cavity shapes and topology near closure region as well as the cavity pressure under different experimental conditions are captured simultaneously. The results are compared across different cavitator shapes and the disk cavitator situated on the downstream side of the mount strut, referred to as backward-facing model (BFM). Similar <math>CQf-Fr</math> curves were observed in BFM and FFM-configured disk cavitators. The cone-shaped cavitator requires the least amount of ventilation to generate a supercavity among all different shapes across the range of <math>Fr</math> in our experiments. The <math>CQc</math>of disk FFM is lower than that of its BFM counterpart at small <math>Fr</math> and exceeds the BFM <math>CQc</math>with further increase of <math>Fr</math>. The cone cavitator has the smallest <math>CQc</math> among all the cavitators across the range of <math>Fr</math> in our experiments. To elucidate the trends of <math>CQc</math> upon changing <math>Fr</math> and cavitator shape, the geometry of supercavity under <math>CQc</math> including its overall shape, the cavity maximum diameter (<math>Dmax</math>) and half length (<math>L1/2</math>) are also investigated. Both <math>Dmax</math> and <math>L1/2</math> show an increasing then plateauing trend upon increasing <math>Fr</math> across different FFM cavitators despite the smaller values for the 3D cone cavitator. Subsequently, such cavity geometric information and cavity pressure measurements in conjunction with high speed imaging of re-entrant jet are employed to estimate the re-entrant jet momentum under different <math>Fr</math> for disk and cone cavitators. The estimated re-entrant jet momentum shows reasonable match with the ventilation air momentum under <math>CQc</math> in lower <math>Fr</math> for both cavitator cases, with the disk cavitator case yielding significantly stronger re-entrant jet, providing support to the re-entrant jet mechanism governing on the cavity collapse. Our study sheds some light on the cavitator design and ventilation strategy for a supercavitating vehicle in practice.

On the Nonlinear Hydrodynamic Characteristic of a Ventilated Supercavitating Vehicle with High Froude Number

Experimental and numerical analysis of the physical characteristics of natural and ventilated supercavitating flows

Numerical analysis of cavitation and impact load characteristics of supercavitating vehicle entering water at high speed

Experimental investigation of the dynamic evolution of cavity during the free water-exit of a high-pressure venting vehicle

Numerical investigation of ventilated cavitating flow from high to low cavitation numbers

Analysis of Ventilated Cavitation Around A Cylinder Vehicle with Nature Cavitation Using A New Simulation Method

NUMERICAL INVESTIGATION OF THE VENTILATED CAVITATING FLOW AROUND AN UNDER-WATER VEHICLE BASED ON A THREE-COMPONENT CAVITATION MODEL

Numerical investigation of positive effects of ventilated cavitation around a NACA66 hydrofoil

Numerical Simulation of Cavitation Flow under High Pressure and Temperature

Numerical Analyses of Ventilated Cavitation over a 2-D NACA0015 Hydrofoil Using Two Turbulence Modeling Methods

Numerical Investigations of Pressure Distribution Inside A Ventilated Supercavity

Numerical investigation of pulsating energy evolution in ventilated cavitation around the NACA0015 hydrofoil

Experimental and numerical study of ventilation cavitation around a NACA0015 hydrofoil with special emphasis on bubble evolution and air-vapor interactions

Experimental and numerical study on flow dynamics and universal characteristics of ventilated supercavities behind different cavitators

Insights into ventilation hysteresis shift due to flow unsteadiness in ventilated supercavitation

Dynamics of the supercavitating hydrofoil with cavitator in steady flow field

Numerical study of the behaviors of ventilated supercavities in a periodic gust flow

Numerical Simulation of Ventilated Cavitation Evolution with an Insight on How Ventilation Influences Pressure Fluctuation and Cavitation Noise

The experimental and numerical studies of formation and collapse processes of ventilated supercavitating flow

Mode vortex and turbulence in ventilated cavitation over hydrofoils

Effect of mounting strut and cavitator shape on the ventilation demand for ventilated supercavitation