Abstract:The quenching and partitioning (Q&P) process is a promising method to create novel martensitic steels with improved balance of strength and ductility by retaining considerable amount of austenite in martensitic matrix. This kind of microstructure provides suitable condition to study wear and abrasion mechanism since the effect of retained austenite on the wear property of martensitic steel is still controversial by now. Selecting traditional quenching and tempering (Q&T) sample with identical composition Fe-0.4C-1.5Mn-1.5Si as reference, the dry sliding wear property of Q&P samples with different austenitization temperatures was studied. The results show that the volume fraction of retained austenite in Q&P samples with full austenitization at 860 or 1000 degrees C respectively is nearly the same (about 14.37% in the former and about 13.79% in the later), and the corresponding carbon concentration (mass fraction) in retained austenite is relatively high (1.37% in the former and 1.38% in the later). Under the conditions of low loading (50 N) and slide speed (40 mm/s), it is not easy to induce martensitic transformation because of very strong mechanical stability, leading to the low friction and wear resistance of samples. The slight better wear resistance of samples with low austenitization temperature can be attributed to microstructural refinement. When the austenitization temperature was 800 degrees C, the intercritical Q&P samples were obtained. Microstructure analysis indicates there exist the highest volume fraction of retained austenite (about 22.28%) and a small volume fraction of ferrite (about 6.75%) in martensitic matrix, which results in the lowest microhardness among present four kinds of samples. However, the mechanical stability of retained austenite in this kind of sample is weak due to the low carbon concentration (about 1.06%). The obvious martensitic transformation accompanying sliding wear contributes to extra hardening and provides additional compressive stress on the touching surface caused by volume expansion. Therefore, the intercritical Q&P samples exhibit the best wear resistance. Based on the experimental results, it is true that the mechanical stability instead of the amount of retained austenite in martensitic steel plays a critical role in improving wear resistance.

Obtaining Superior Low-Temperature Wear Resistance in Q&P-processed Medium Mn Steel with a Low Initial Hardness

Wear Conditions-Dependent Tribological Behavior in Q&P Medium-Mn Steels: the Role of TRIP Effect and Strain Hardening

Effect of Austenitization Temperature on the Dry Sliding Wear Properties of a Medium Carbon Quenching and Partitioning Steel

Macroscopic and Nanoscale Investigation of the Enhanced Wear Properties of Medium-Mn Steel Processed Via Room-Temperature Quenching and Partitioning

A Comparative Study on the Three-Body Abrasive Wear Performance of Q&P Processing and Low-Temperature Bainitic Transformation for a Medium-Carbon Dual-Phase Steel

The Coupled Effect Of Thermal And Mechanical Stabilities Of Austenite On The Wear Resistance In A 0.2c-5mn-1.6si Steel Down To Cryogenic Temperatures

A Comparative Study on the Wear Behavior of Quenched-and-Partitioned Steel (Q&P) and Martensite Steel (Q&T)

Unraveling the significant role of retained austenite on the dry sliding wear behavior of medium manganese steel

Microstructure and Mechanical Properties of Ultra-high Strength Q&P Steel with 3.5% Mn

Low Temperature Microstructure and Mechanical Properties of a Low Carbon Alloy Steel by Quenching-Partitioning-tempering Process

Influence of Isothermal Treatment Prior to Initial Quenching of Q&P Process on Microstructure and Mechanical Properties of Medium Mn Steel

Influence of Quenching and Partitioning Parameters on Phase Transformations and Mechanical Properties of Medium Manganese Steel for Press-Hardening Application

Low Carbon Si-Mn Q&P Steel Plasticity Enhancement Mechanisms and Microstructure Property

Comparison of the Impact Wear Performances of Quenching and Partitioning and Quenching and Tempering Steels

Effect of Retained Austenite on Wear Resistance of Nanostructured Dual Phase Steels

Effects of hot/cold deformation on the microstructures and mechanical properties of ultra-low carbon medium manganese quenching-partitioning-tempering steels

Improvement of mechanical properties and wear resistance of direct‐quenched wear‐resistant steel by deformed austenite

The Mechanism of High-Strength Quenching-Partitioning-Tempering Martensitic Steel at Elevated Temperatures

Influence of Q & P process on microstructure and mechanical properties of 20 Si2 Mn steel

Relation Between Microstructure and Formability of Quenching-Partitioning-Tempering Martensitic Steel

Microstructure and mechanical properties of a low-carbon HDQ&P steel