Abstract:We report an experimental investigation of the wake of free falling super-hydrophobic spheres. The mutual interaction between the air layer (plastron) encapsulating the super-hydrophobic spheres and the flow is emphasised by studying the hydrodynamic performance. It is found that the air plastron adapts its shape to the flow-induced stresses which compete with the surface tension. This competition is characterised by introducing the Weber number ${\mathcal{W}}e$ , whilst the plastron deformation is estimated via the aspect ratio $\unicode[STIX]{x1D712}$ . While noticeable distortions are locally observed, the plastron becomes more and more spherical on average (i.e. $\unicode[STIX]{x1D712}\rightarrow 1$ ) as far as ${\mathcal{W}}e$ increases. The study of the falling motion reveals that the plastron compliance has a sizeable influence on the wake development. Investigating the lift force experienced by the super-hydrophobic spheres, the onset of wake instabilities is found to be triggered earlier than for smooth spheres used as reference. Surprisingly, it is also observed that the early promotion of the wake instabilities is even more pronounced beyond a critical Weber number, ${\mathcal{W}}e_{c}$ , which corresponds to a critical aspect ratio $\unicode[STIX]{x1D712}_{c}$ . Furthermore, the magnitude of the hydrodynamic loads is found to be dependent on the average deformation of the gas/liquid interface. Indeed, in comparison to the reference spheres, the high deformation achieved for $\unicode[STIX]{x1D712}>\unicode[STIX]{x1D712}_{c}$ (oblate shape) leads to lift and drag increase, whereas the low deformation obtained for $\unicode[STIX]{x1D712}<\unicode[STIX]{x1D712}_{c}$ (spherical shape) yields lift and drag mitigation. Accordingly, taking into account the plastron deformation provides an attractive way to explain the somehow discordant results reported in other studies at comparable Reynolds numbers. These results suggest that the amount of vorticity produced at the body surface and then released in the wake is strongly impacted by the plastron compliance. If confirmed by additional studies and extrapolated to other flow configurations, our findings would imply that plastron compliance and its feedback on the flow, which are currently neglected in most theoretical works and numerical simulations, must be accounted for to design super-hydrophobic surfaces and/or predict their performance.

Second-Level Microgroove Convexity is Critical for Air Plastron Restoration on Immersed Hierarchical Superhydrophobic Surfaces

Microgroove convexity is critical for robust gaseous layers on hierarchically-structured superhydrophobic surfaces

Salvinia-inspired Surfaces for Enhancing the Preservation of Air Plastrons under Negative Pressure

On Interfacial Deformation and Resistance Characteristics over Superhydrophobic Surfaces: A Numerical Study

Enhancing Resistance to Wetting Transition through the Concave Structures

Self-Driven Gas Spreading on Mesh Surfaces for Regeneration of Underwater Superhydrophobicity

Lotus Rhizome-Inspired Superhydrophobic Capillarity Mesh Surface for Long-Term Plastron Stability

Plastron Regeneration on Submerged Superhydrophobic Surfaces Using In Situ Gas Generation by Chemical Reaction

Superrepellency of underwater hierarchical structures on Salvinia leaf

STABILITY AND RECOVERABILITY OF LIQUID-GAS INTERFACES ON SUBMERGED HIERARCHICALLY STRUCTURED SURFACES

Interaction between cavitation bubbles and plastrons on superhydrophobic surfaces

Effects of hierarchical features on longevity of submerged superhydrophobic surfaces with parallel grooves

Fouling Inhibition by Replenishable Plastrons on Microstructured, Superhydrophobic Carbon‐Silicone Composite Coatings

Hierarchically Sculptured Plant Surfaces and Superhydrophobicity

Wake of super-hydrophobic falling spheres: influence of the air layer deformation

Predicting plastron thermodynamic stability for underwater superhydrophobicity

Influence of entrapped gas morphology at liquid–solid interface on underwater drag reduction effect

Effective Unidirectional Wetting of Liquids on Multi-Gradient, Bio-Inspired Surfaces Fabricated by 3D Printing and Surface Modification

<i>Salvinia</i>-like slippery surface with stable and mobile water/air contact line

Self-Compensating Liquid-Repellent Surfaces with Stratified Morphology

Designing Plastrons for Underwater Bubble Capture: From Model Microstructures to Stochastic Nanostructures