Abstract:New developments in instrumentation for ocean environmental engineering are allowing unprecedented levels of trace contaminant measurement in the deep ocean. With funding from the U.S. National Science Foundation (NSF), our engineering design team constructed a new mass spectrometer-based in situ analysis system for work in the deep ocean environment over prolonged deployment periods. Our design goals were a depth capability of up to 4,000 m water depth (400 bars hydrostatic pressure) and autonomous operation for periods of up to six months to a year, depending upon the type of external battery system used or other deployment circumstances, e.g., availability of a power cable or fuel cell power source. We chose a membrane introduction mass spectrometry (MIMS) sampling approach, which allows for dissolved gases and volatile organics introduction into the mass spectrometer vacuum system. The MIMS approach and the hydrophobic, silicon-coated membrane chosen both draw upon our previous experience with this technology in the deep ocean. The membrane has been tested to 400 bars in a series of long-term hydrostatic pressure tests, which extend the 200-bar working depth rating of this membrane by a factor of 2. Long-term deployment capability of the moderately powered, approximately 100 W system, was accomplished by power management of the embedded computer system and custom electronics with Windows-based and custom software now fully-developed and bench tested. The entire system fits within a 6.5-inch outside diameter pressure housing that is approximately five feet long. It consists of a 1 to 200 amu range quadrupole mass spectrometer equipped with Faraday and electron multiplier detectors, compact turbo-molecular and backing diaphragm vacuum pumps, internal rechargeable batteries, and internal waste vacuum chamber. Sample routing past the MIMS is accomplished by computer-controlled solenoid valves. We designed the pressure housings of both 6AL4V and type 2 titanium alloys that are rated to working depths of >4,000 m and are essentially corrosion proof over long-term deployments. We designed and integrated a fail-safe valving system for both rapid response to high-pressure MIMS failure and a pressure-switch circuit and high-pressure solenoid valve to detect and protect against slow leaks of the MIMS. To route sample waters to the MIMS-based instrument, we also designed and built a rugged plastic plenum that couples to the face of the sampler head, the latter of which consists of the MIMS inlet and a full-ocean rated thermister temperature probe with an operational range from −5 to 50°C. These instrumentation innovations will be described in the paper.

Deep-Sea Membrane Condition Monitoring Based on Wireless Humidity Measurement

A Capacitive Pressure Sensor with Adjustable Working Range for Deep Sea

Facile Fabrication of Poly (diallyldimethyl Ammonium Chloride)/ti3c2tx/poly (vinylidene Fluoride) 3D Hollow Fiber Membrane Flexible Humidity Sensor and Its Application in the Monitoring of Health-Related Physiological Activity

High-resolution Quasi-Distributed Temperature and Pressure Sensing System for Deep-Sea Reservoir Monitoring

Noninvasive Real-Time Monitoring of Wetting Progression in Membrane Distillation Using Impedance Spectroscopy

In-situ Measurement of Temperature and Humidity Distribution in Gas Channels for Commercial-Size Proton Exchange Membrane Fuel Cells

Underwater Temperature and Salinity Fiber Sensor Based on Semi-open Cavity Structure of Asymmetric MZI

A sandwich temperature control membrane inlet mass spectrometer for dissolved gases and volatile organic compounds in aqueous solution

Waterproof Breathable Multifunctional Flexible Sensor for Underwater Tactile Sensing and Ammonia Gas Monitoring

Strain-Insensitive Optical Fiber Sensor for Temperature and Salinity Measurement With Polynomial Surface Decoupling Algorithm

Wide Remote-Range and Accurate Wireless LC Temperature-Humidity Sensor Enabled by Efficient Mutual Interference Mitigation.

Multifunctional pressure and humidity sensor modulated by electrostatic interactions and hydrogen bonds for wearable health monitoring

A Direct-Reading MEMS Conductivity Sensor with a Parallel-Symmetric Four-Electrode Configuration

Wireless and Passive SAW-Based Humidity Sensor Employing SiO2 Thin Film

Online Monitoring of Seawater Carbon Dioxide Based on an Infrared Rear Beam Splitter

Monolithically Integrated Bidirectional Flow Sensor and Stacked Temperature/Humidity Sensor Based on CMOS-Compatible MEMS Technology

MEMS flexible conformal hydrophone based on heterogeneous integration technology

Mechatronic Integration and Implementation of in Situ Multipoint Temperature Measurement for Seafloor Hydrothermal Vent

Temperature Compensation In Fluid Density Measurement Using Micro-Electromechanical Resonant Sensor

Ultrafast Water Transport in Two-dimensional Vermiculite–Ionic Liquid Composite Membrane to Enhance Rapid Humidity Sensing

A Deep-Ocean Mass Spectrometer to Monitor Hydrocarbon Seeps and Pipelines