Abstract:In organic Rankine cycle (ORC) system, the selection of the structure and the optimization of operating parameters are usually studied separately, which makes the existing design principles inadequate to describe the impacts of the structure on ORC performance, and thus greatly limits its practical applications. To this end, this paper addresses an automated scheme for the optimal configuration of the ORC system, aiming to simultaneously determine the working fluid, the structure and the operating parameters corresponding to the maximal system efficiency. In this work, a comprehensive simulation and optimization of four common ORC structures is first conducted with 18 working fluid candidates and the most common heat sources with the inlet temperature ranging at 200-120 degrees C. The influence mechanisms of the ORC structure on the thermodynamic performance of the ORC system are then explored to generalize the qualitative and quantitative principles for ORC configuration. Results show that, for the single-pressure evaporation ORC (SPC) with a given inlet temperature of the heat source, the Pinch point type formed by the working fluid and the heat source changes from vaporization Pinch point (VPP) to VPP&PPP (preheat Pinch point) and then to PPP as the critical temperature of the working fluid decreases. The system efficiency of SPC reaches its maximum when the double Pinch point of VPP and PPP is formed and double-pressure evaporation ORC (DPC) reaches its maximum system efficiency when the double Pinch points of HVPP and LVPP are formed. Besides, it is found that when compared with the basic ORC, the regenerative ORC enables to improve the thermal efficiency and system efficiency of the system at the same time, whereas the bleeding regenerative ORC increases the thermal efficiency while reduces the system efficiency. For the DPC, the type of Pinch point formed by the heat source and the working fluid in the optimal working condition is the key to determine whether a system has multiple evaporation potential. Specially, for the heat source with variable inlet temperature, a linear relationship between the inlet temperature of the heat source and the critical temperature of the working fluid can be established to determine the multiple evaporation potential of a certain working fluid. Based on these results, an automatic scheme for ORC configuration is developed and expected to provide an effective guidance for the selection of working fluid, configuration optimization and parameter determination of the actual ORC heat recovery process.

On the CAMD Method Based on PC-SAFT for Working Fluid Design of a High-Temperature Organic Rankine Cycle

Advances in Working Fluids for Organic Rankine Cycle

Working Fluid Selection for a Small-Scale Organic Rankine Cycle Recovering Engine Waste Heat

Simultaneous Optimization for Organic Rankine Cycle Design and Heat Integration

An Effective Method for Working Fluid Design of Organic Rankine Cycle

Possibility of Optimal Efficiency Prediction of an Organic Rankine Cycle Based on Molecular Property Method for High-Temperature Exhaust Gases

Performance Prediction and Working Fluid Active Design of Organic Rankine Cycle Based on Molecular Structure

Intrinsic-Group-Contribution Pc-Saft and Its Application in Performance Analysis of High-Temperature Organic Rankine Cycle with Siloxanes and Alkanes

Working Fluid Selection For Medium Temperature Organic Rankine Cycle

Combining Cubic Equations with Group Contribution Methods to Predict Cycle Performances and Design Working Fluids for Four Different Organic Rankine Cycles

Automated Configuration of Organic Rankine Cycle System Based on Process Simulations

Systematic Fluid Selection for Organic Rankine Cycles and Performance Analysis for a Combined High and Low Temperature Cycle

Enhancing Working Fluid Selection for Novel Cogeneration Systems by Integrating Predictive Modeling: from Molecular Simulation to Process Evaluation

Thermodynamic Analysis and Optimization of Organic Rankine Cycles Based on Radial-Inflow Turbine Design

Selection and Evaluation of Dry and Isentropic Organic Working Fluids Used in Organic Rankine Cycle Based on the Turning Point on Their Saturated Vapor Curves

Multi-objective Optimisation and Fast Decision-Making Method for Working Fluid Selection in Organic Rankine Cycle with Low-Temperature Waste Heat Source in Industry

Working Fluid Selection and Preliminary Design of a Solar Organic Rankine Cycle System

A Novel Comprehensive Evaluation Methodology of Organic Rankine Cycle for Parameters Design and Working Fluid Selection

Exploration and Analysis of CO2 + Hydrocarbons Mixtures As Working Fluids for Trans-critical ORC

Evaluation of working fluids for organic Rankine cycles using group-contribution methods and second-law-based models

Multi-objective optimization and fluid selection of organic Rankine cycle (ORC) system based on economic-environmental-sustainable analysis