Transformation of Triolein to Biogasoline by Photo-Chemo-biocatalysis

Weihua Xu,Kaihao Mou,Haonan Zhou,Jian Xu,Qi Wu

DOI: https://doi.org/10.1039/d2gc01992b

IF: 9.8

2022-01-01

Green Chemistry

Abstract:Photo-chemo-biocatalytic sequential reactions for the green production of biogasoline from natural abundant lipids and even wasted or non-edible oil by using solar energy and atmospheric O2 under mild conditions.

What problem does this paper attempt to address?

Hydrogen Production from Bio-Derived Biphasic Photoreforming over a Raspberry-Like Amphiphilic Ag2O-TiO2/SiO2 Catalyst

Enqi Bu,Ying Chen,Chao Wang,Zhengdong Cheng,Xianglong Luo,Riyang Shu,Jingtao Zhang,Mingzheng Liao,Zhiqiang Jiang,Qingbin Song

DOI: https://doi.org/10.1016/j.cej.2019.03.259

IF: 15.1

2019-01-01

Chemical Engineering Journal

Abstract:Photoreforming of bio-derived liquids is anattractive approach toward sustainable H-2 production. Although a large number of bio-liquids are thermodynamically feasible for photocatalytic hydrogen production, few of them have been involved in this process due to their water insoluble nature. To achieve and promote the efficiency of photoreforming hydrogen production in bio-derived biphasic system, the Pickering interfacial catalysis was established over an amphiphilic Ag2O-TiO2/SiO2 catalyst. In this case, the Ag2O-TiO2/SiO2 sample was synthesized by means of an electrostatic self-assembly method by surface charge regulation of SiO2 and the surface hydrophobic modification of Ag2O-TiO2/SiO2 particles using a Pickering emulsion method. As shown in the results, the amphiphilic Ag2O-TiO2/SiO2 particles were observed to successfully stabilize the bio-octanol/water emulsion. Even the complex structure and surface modification slightly reduce the light absorption efficiency and specific surface area of the catalyst, the hydrogen yield was greatly promoted over Ag2O-TiO2/SiO(2 )compared to that of bare TiO2, Ag2O-TiO2 and TiO2/SiO2. It was also discovered that the cyclic hydrogen production performance can be improved by simple re-emulsification. The effect of bio-octanol concentration for photoreforming was studied by a Langmuir-Hinshelwood-type kinetic model, and the reaction rate constant and biooctanol adsorption constant were obtained. This study shows that photocatalyst after effective surface amphiphilic modification could provide a prospective approach for the hydrogen production from a bio-derived oil/ water biphasic system under solar light.
Photoenzymatic Production of Next Generation Biofuels from Natural Triglycerides Combining a Hydrolase and a Photodecarboxylase

Yunjian Ma,Xizhen Zhang,Wuyuan Zhang,Peilin Li,Yongru Li,Frank Hollmann,Yonghua Wang

DOI: https://doi.org/10.1002/cptc.201900205

2019-01-01

ChemPhotoChem

Abstract:A photobiocatalytic cascade transforming natural triglycerides into alkanes/alkenes is proposed. Starting from natural triglycerides, free fatty acids have been obtained using lipases. The free fatty acids were then, in a photoenzymatic step, decarboxylated into the C1-shortened alkanes using a recently described photodecarboxylase from Chlorella variabilis NC64A. This cascade produced alkanes from various natural (waste) oils in significant amounts (up to 24 g L−1) and may provide a basis for valorisation of waste oils into a next generation of biodiesel.
Transesterification of Methyl Oleate for Sustainable Production of Biolubricant: Process Optimization and Kinetic Study

Qinglong Xie,Huiyun Zhu,Pan Xu,Kainan Xing,Shangzhi Yu,Xiaojiang Liang,Weirong Ji,Yong Nie,Jianbing Ji

DOI: https://doi.org/10.1016/j.indcrop.2022.114879

IF: 6.449

2022-01-01

Industrial Crops and Products

Abstract:Trimethylolpropane fatty acid triester (TFATE) is a promising biolubricant as an environmentally friendly substitute to conventional mineral-based lubricants. However, the issues of extensive energy consumption from vacuum maintenance and feedstock saponification caused by strong alkaline catalysts exist in current TFATEbased biolubricant synthesis. Here, sustainable production of biolubricant was achieved with methyl oleate (MO) from non-edible oil sources as the feedstock and moderate alkaline K2CO3 as the catalyst. Nitrogen gas stripping method instead of vacuum was adopted for methanol removal. The effects of agitation speed, N-2 flow rate, catalyst amount, MO to trimethylolpropane (TMP) molar ratio and temperature on MO conversion and TFATE selectivity were examined. The TFATE selectivity reached 95.6% under the optimized conditions. Leaching tests indicated neglectable K2CO3 dissolution in reaction products. The kinetic parameters for the three consecutive transesterification reactions were calculated. In addition, the synthesized biolubricants exhibit low acid value and volatility, moderate iodine value, superior thermal stability, and good rheological and frictional properties.
Lipase and photodecarboxylase co-expression: A potential strategy for alkane-based biodiesel production from natural triglycerides

Yong-Yi Zeng,Xin-Yi Xu,Jin-Xuan Xie,Wen-Li Chen,Lan Liu,Xin-Jian Yin,Bi-Shuang Chen

DOI: https://doi.org/10.1016/j.cjche.2023.11.013

IF: 3.8

2023-12-09

Chinese Journal of Chemical Engineering

Abstract:Alkane-based biodiesel is considered the next generation of biodiesel owing to its potential environmental benefits and the fact that it exhibits much higher specific caloric values than traditional biodiesel. However, the formidable obstacle impeding the commercialization of this cutting-edge fuel alternative lies in the cost associated with its production. In this study, an engineered strain Escherichia coli ( E. coli ) showcasing harmonized coexpression of a lipase (from Thermomyces lanuginosus , TL L) and a fatty acid photodecarboxylase (from Chlorella variabilis , Cv FAP) was first constructed to transform triglycerides into alkanes. The potential of E. coli BL21 (DE3)/pRSFDuet-1- TL L- Cv FAP for alkane synthesis was evaluated with tripalmitin as a model substrate under various process conditions. Following a comprehensive examination of the reaction parameters, the scope of the biotransformation was expanded to 'real' substrates (vegetable oils). The results showed that bioderived oils can be transformed into alkanes with high yields (0.80–10.20 mmol·L –1 ) under mild conditions (35 °C, pH 8.0 and 36 h) and blue light illumination. The selected processes were performed on an increased lab scale (up to 100 ml) with up to 24.77 mmol·L –1 tripalmitin, leading to a yield of 18.89 mmol·L –1 pentadecane. With the employment of a method for efficiently producing alkanes under mild conditions alongside a simple procedure to isolate alkanes from the reaction system, the utilization of sustainable biomass as a fundamental feedstock emerges as the primary solution to lower the cost of alkane-based biodiesel. Thus, this study proposes a readily implementable and highly effective approach for alkane-based biodiesel production.

engineering, chemical
Recovery Utilization of Triolein for Producing Short Chain Alkane by Combining Biocatalysis and Inorganic Catalysis

Jie Zhang,Ling Gao,Yao Lu,Lixiu Yan,Xuemei Tan,Zhehan Yang,Huijun Zhang

DOI: https://doi.org/10.1080/15567036.2023.2182847

2023-01-01

Abstract:The production of waste cooking oil (WCO) has been increasing year by year and brought the serious environmental problems. A considerable research effort has been focused on the reuse of WCO. Utilizing the triolein existing in great quantity on olive oil and rapeseed oil is an effective strategy to realize the reuse of WCO. This work introduces a novel process for producing short-chain alkane from triolein based on the convenience of products separation. The continuous process including the hydrolysis of triolein into fatty acid by lipase, the oxidation of fatty acid for producing short-chain fatty acid, and the light-driven decarboxylation of short chain fatty acids was established to produce alkane. The feasibility of the proposed process was demonstrated using model substances. The influences of various operational parameters on hydrolysis, oxidation, and decarboxylation using model substances were studied systematically. The optimized yields of the hydrolysis, oxidation, and decarboxylation reactions were 78.7%, 52.1%, and 78.9%, respectively. The free lipase is reused under the optimal condition and observed that 31.9% decay in catalytic activity even 5 cycles. Immiscible reaction systems are used to facilitate separation of products. The decarboxylation with decarboxylase (CvFAP) for short-chain fatty acid lead to higher alkane yields in 15 min. In addition, the octane yield of 16.2% using triolein as the raw material was obtained in the continuous process. Although this approach results in a low total yield of gasoline, it highlights the potential applications in the production of hydrocarbon fuel with WCO.
Catalytic transformations of acids, aldehydes, and phenols in bio-oil to alcohols and esters

wen chen,zhongyang luo,chunjiang yu,guoxiang li,yi yang,jixiang zhang,kongyu lu

DOI: https://doi.org/10.1016/j.fuel.2014.06.003

IF: 7.4

2014-01-01

Fuel

Abstract:•A method to convert acids, aldehydes, and phenols to alcohols and esters was proposed.•C-supported catalysts gave complete conversion of phenol and n-butanal.•Esterification was mainly catalyzed by weak and medium acid sites.•Yields of desired products (alcohols and esters) as high as 95% could be achieved in OHE.
Photothermal technique-enabled ambient production of microalgae biodiesel: Mechanism and life cycle assessment

Jinshu Huang,Junqi Wang,Zhuochun Huang,Tengyu Liu,Hu Li

DOI: https://doi.org/10.1016/j.biortech.2022.128390

Abstract:Thermocatalytic (trans)esterification of oils/lipids to produce biodiesel is generally energy-consuming, reversible, and controlled by the equilibrium law. Herein, a light-induced photothermal process was illustrated to be highly efficient for biodiesel production (96.8 % yield) from microalgae lipids at room temperature enabled by a biomass-based SO3H-functionalized graphene-like heterogeneous catalyst (S-NGL-600), as optimized by response surface methodology. Infrared thermal imaging indicated that interfacial solar heating led to forming a local photothermal catalytic system, reaching 72.2 °C in 2 min. The local light heating was conducive to evaporation and removal of water from acid sites, resulting in local excess of microalgae lipids to facilitate the forward reaction. Notably, the photothermal catalyst was highly recyclable and exhibited a significantly higher conversion rate of microalgae lipids than industrially used catalyst H2SO4. Life cycle assessment suggested energy-saving advantage (0.87 MJ/MJ) and environmental protection (-89.42 CO2eq/MJ) of the photothermal-driven protocol for microalgae biodiesel production.
Catalytic Transformation Of Bio-Oil To Benzaldehyde And Benzoic Acid: An Approach For The Production Of High-Value Aromatic Bio-Chemicals

Xiaoping Wu,Lijuan Zhu,Changhui Zhu,Chenguang Wang,Quanxin Li

DOI: https://doi.org/10.2174/2213346106666190830114619

2019-01-01

Current Green Chemistry

Abstract:Benzaldehyde and benzoic acid are high-value aromatic chemicals and important intermediates in chemical industry, and the catalytic conversion of biomass-based sources to these aromatic chemicals is of great significance in both academic and industrial fields. This work demonstrated that bio-oil was directionally converted into benzaldehyde and benzoic acid by three-step process under atmospheric pressure and moderate temperatures. The process included the catalytic cracking of bio-oil into aromatics over 1% Ga/HZSM-5 catalyst, followed by the dealkylation of heavier alkylaromatics to toluene over Re/HY catalyst and the liquid-phase oxidation of toluene-rich aromatics to the targeted chemicals over CoCl2/NHPI (CoCl2/N-Hydroxyphthalimide) catalyst. The production of benzaldehyde and benzoic acid from the bio-oil-derived aromatics, with the overall selectivity of 86.8%, was achieved using CoCl2/NHPI catalyst at 100 degrees C. Furthermore, adding a small amount of methanol into the feed would efficiently suppress the coke formation, and thus, enhance the yield of aromatics. Potentially, the novel synthesis route offers a green way for the production of higher value-added aromatic chemicals using renewable and environmentally friendly biomass-based sources.
Converting Glycerol into Valuable Trioses by Cuδ+‐Single‐Atom‐Decorated WO3 under Visible Light

Lunqiao Xiong,Zhounan Yu,Hongchen Cao,Weixiang Guan,Yang Su,Xiaoli Pan,Leilei Zhang,Xiaoyan Liu,Aiqin Wang,Junwang Tang

DOI: https://doi.org/10.1002/anie.202318461

2024-02-03

Angewandte Chemie International Edition

Abstract:Photocatalytic selective oxidation under visible light presents a promising approach for the sustainable transformation of biomass-derived wastes. However, achieving both high conversion and excellent selectivity poses a significant challenge. In this study, two valuable trioses, glyceraldehyde and dihydroxyacetone, are produced from glycerol over Cuδ+-decorated WO3 photocatalyst in the presence of H2O2. The photocatalyst exhibits a remarkable five-fold increase in the conversion rate (3.81 mmol·g-1·h-1) while maintaining a high selectivity towards two trioses (46.4% to glyceraldehyde and 32.9% to dihydroxyacetone). Through a comprehensive analysis involving X-ray photoelectron spectroscopy measurements with and without light irradiation, electron spin resonance spectroscopy, and isotopic analysis, the critical role of Cu+ species has been explored as efficient hole acceptors. These species facilitate charge transfer, promoting glycerol oxidation by photoholes, followed by coupling with OH-, which are subsequently dehydrated to yield the desired glyceraldehyde and dihydroxyacetone.

chemistry, multidisciplinary
Thermo-chemical Conversion of Chlorella Pyrenoidosa to Liquid Biofuels.

Peigao Duan,Binbin Jin,Yuping Xu,Yan Yang,Xiujun Bai,Feng Wang,Lei Zhang,Jun Miao

DOI: https://doi.org/10.1016/j.biortech.2013.01.069

IF: 11.4

2013-01-01

Bioresource Technology

Abstract:The aim of the present study is to find how the solvent polarity affects the liquefaction behavior of Chlorella pyrenoidosa and subsequently using the most suitable solvent identified to explore the solvent/biomass ratio, time, and temperature on the products yield and properties of the bio-oil. The products yield was significantly affected by the solvent type, and ethanol was proven to be the most suitable solvent to convert C. pyrenoidosa into bio-oil from the yield and economic points of view. Temperature is the most influential factor on the products yield and properties of the bio-oil. The HHVs of the bio-oils produced under different reaction conditions are within the range of 27.68–36.45MJ/kg. The major compounds in bio-oil were esters, fatty acids, alkenes, aldehydes, and amides, and fatty acid ethyl esters were the largest portion.
Production and characterization of bio-oil from hydrothermal liquefaction of microalgae Dunaliella tertiolecta cake

Zou Shuping,Wu Yulong,Yang Mingde,Imdad Kaleem,Li Chun,Junmao Tong

DOI: https://doi.org/10.1016/j.energy.2010.07.013

IF: 9

2010-01-01

Energy

Abstract:Renewable fuels are major alternatives to conventional fossil fuels. Biomass in the form of agricultural and industrial residues is fast becoming popular among new renewable energy sources. Hydrothermal liquefaction can thermochemically convert biomass residues into bio-oil. This work investigates the hydrothermal liquefaction of microalgae Dunaliella tertiolecta cake under various liquefaction temperatures, holding times, and catalyst dosages. A maximum bio-oil yield of 25.8% is obtained at a reaction temperature of 360 degrees C and a holding time of 50 min using 5% Na2CO3 as a catalyst. The various physical and chemical characteristics of bio-oil obtained under the most suitable conditions are determined, and a detailed chemical compositional analysis of bio-oil is performed using an elemental analyzer. Fourier transform-infrared spectroscopic analysis (FT-IR), and gas chromatography mass spectrometry (GC MS). The bio-oil is composed of fatty acids, fatty acid methyl esters, ketones, and aldehydes. Its empirical formula is CH1.44O0.29N0.05. and its heating value is 30.74 MJ/kg. The bio-oil product is a possible eco-friendly green biofuel and chemical. (C) 2010 Elsevier Ltd. All rights reserved.
Synergistically Photocatalytic Conversion of Two Greenhouse Gases to Liquid‐Phase Oxygenates under Anaerobic Conditions

Haiting Lin,Anyi Chen,Tianren Liu,Wensheng Zhang,Xinyv Du,Junjie Feng,Jiajun Zeng,Yingying Fan,Dongxue Han,Li Niu

DOI: https://doi.org/10.1002/solr.202400522

IF: 9.1726

2024-08-21

Solar RRL

Abstract:Methane and carbon dioxide are two typical greenhouse gases. Collaboratively converting methane and carbon dioxide into valuable chemicals via photocatalysis represents a sustainable route to energy storage and value‐added manufacture. In this work, a highly synergetic effect between methane oxidation and carbon dioxide reduction into liquid chemicals is achieved on anatase phase of titanium dioxide. Collaborative conversion of methane and carbon dioxide into sustainable chemicals is an appealing solution to simultaneously overcome both environmental problems and energy crisis. However, this reaction is limited to the preparation of syngas with the unfavorable feature for transportation and storage. Herein, liquid formaldehyde as product is fabricated by the collaborative conversion of methane and carbon dioxide using anatase phase titanium dioxide as photocatalyst. The productivity reaches 14.65 mmol g−1 with 88.32% selectivity. In situ diffuse reflectance Fourier transform infrared spectroscopy, isotope testes, and theoretical calculation clarify that the photoexcited holes and electrons engage into methane oxidation and carbon dioxide reduction over anatase using surface hydroxyl species and oxygen vacancy as active sites, respectively. The consumption of surface hydroxyl species on methane oxidation promotes the oxygen vacancy formation for carbon dioxide adsorption, mutually the carbon dioxide provides the oxygen atom for surface hydroxyl species facilitating methane oxidation. The consumption of photoelectrons and photoholes on carbon dioxide reduction and methane oxidation balances the number of photogenerated carriers and ensures the catalytic system stability. In this work, the avenue is broadened toward the co‐conversion of greenhouse gas into desirable chemical products in a sustainable way.

energy & fuels,materials science, multidisciplinary
Continuous hydrocarbon fuels production by photoenzymatic decarboxylation of free fatty acids from waste oils

Feng Li,Ao Xia,Xiaobo Guo,Wuyuan Zhang,Yun Huang,Xianqing Zhu,Xun Zhu,Qiang Liao

DOI: https://doi.org/10.1016/j.jece.2023.110748

IF: 7.7

2023-08-17

Journal of Environmental Chemical Engineering

Abstract:Fatty acid photodecarboxylase, recently found in Chlorella variabilis NC64A ( Cv FAP), could efficiently catalyze C16-C18 fatty acids into C1-shortened hydrocarbons under visible light. This provides an alternative approach for hydrocarbon fuels production in mild conditions compared with hydrotreating of oils. In this study, a cascade system integrating lipase hydrolysis and Cv FAP decarboxylation was demonstrated for the efficient production of hydrocarbon fuels from waste oils. The continuous Cv FAP-catalyzed decarboxylation characteristics and performance of free fatty acids derived from waste oil were investigated for the first time. A hydrocarbon fuel production rate of 18.4 mM/h was obtained at a residence time of 50 min. The regulation of pH value from 6.8 to 8.5 significantly improved the activity of Cv FAP, thereby obtaining an optimal conversion of 61.2%. The precipitation of palmitic acid caused a low conversion (37.9%) compared with the other fatty acids, further inhibiting hydrocarbon production. In such a cascade system, various oils can be converted to hydrocarbon fuels with a concentration of 8.97–15.3 mM. A high energy production rate of 204.3 kJ/L/h was achieved, which exhibited the advancement in high-quality biofuel production.

engineering, chemical, environmental
Research on biocatalyzed artificial photosynthesis

jingfei luan,biaohang chen,zhigang zou

DOI: https://doi.org/10.1016/j.copbio.2013.05.158

IF: 10.279

2013-01-01

Current Opinion in Biotechnology

Abstract:Microbial fermentation for producing biodiesel from lignocellulosic hydrolysates is receiving increasing attention and attempts have been made to screen an oleaginous Trichosporon sp. with high lipid content and a strong tolerance to lignocellulose hydrolysates. In order to better understand mechanisms related to its lipid accumulation, metabolic flux analysis was performed under 5 g L−1 ammonium sulfate (high nitrogen) and/or 0.4 g L−1 ammonium sulfate (low nitrogen) conditions. Cell growth phase and lipid accumulation phase were shown for cells grown under low nitrogen condition. Results of flux distribution demonstrated that NADPH provided by cytosolic malic enzyme and the acetyl-CoA from cytoplasmic citrate by the ATP: citrate lyase were the two primary sources for excess lipid accumulation. Flux data also supported the fact that the citrate pyruvate cycle plays an essential role in the lipid accumulation. The flux information obtained could also motivate new design strategies for oleaginous yeasts for enhanced biodiesel production.
Ultra-sonication application in biodiesel production from heterotrophic oleaginous microorganisms.

Jiaxin Chen,Ji Li,Xiaolei Zhang,Rajeshwar Dayal Tyagi,Wenyi Dong

DOI: https://doi.org/10.1080/07388551.2017.1418733

IF: 9.062

2018-01-01

Critical Reviews in Biotechnology

Abstract:Utilization of microbial oil for biodiesel production has gained growing interest due to the increase in prices and the shortage of the oils and fats traditionally used in biodiesel production. However, it is still in the laboratory study stage due to the high cost of production. Employing organic wastes as raw materials to grow heterotrophic oleaginous microorganisms for further lipid production to produce biodiesel has been predicted to be a promising method for reducing costs. However, there are many obstacles including the low biodegradability of organic wastes, low lipid accumulation capacity of heterotrophic oleaginous microorganisms while using organic wastes, a great dependence on a high-energy consumption approach for biomass harvesting, utilization of toxic organic solvents for lipid extraction, and large amount of methanol required in trans-esterification and in-situ trans-esterifications. Ultra-sonication as a green technology has been extensively utilized to enhance bio-product production from organic wastes. In this article, ultra-sonication applications in biodiesel production steps with heterotrophic oleaginous microorganisms have been reviewed, and its impact, potential, and limitations on the process have been discussed.
Photocatalytic Conversion of Waste Plastics into C2 Fuels under Simulated Natural Environment Conditions

Xingchen Jiao,Kai Zheng,Qingxia Chen,Xiaodong Li,Yamin Li,Weiwei Shao,Jiaqi Xu,Junfa Zhu,Yang Pan,Yongfu Sun,Yi Xie

DOI: https://doi.org/10.1002/anie.201915766

2020-09-01

Abstract:Reported here is the first highly selective conversion of various waste plastics into C2 fuels under simulated natural environment conditions by a sequential photoinduced C-C cleavage and coupling pathway, where single-use bags, disposable food containers, food wrap films, and their main components of polyethylene, polypropylene, and polyvinyl chloride can be photocatalytically transformed into CH3 COOH without using sacrificial agents. As an example, polyethylene is photodegraded 100 % into CO2 within 40 h by single-unit-cell thick Nb2 O5 layers, while the produced CO2 is further photoreduced to CH3 COOH. Various methods and experiments disclose that O2 and . OH radicals trigger the oxidative C-C cleavage of polyethylene to form CO2 , while other investigations show that the yielded CH3 COOH stems from CO2 photoreduction by C-C coupling of . COOH intermediates. This two-step plastic-to-fuel conversion may help to simultaneously address the white pollution crisis and harvest highly valuable multicarbon fuels in natural environments.
Photocatalyzing Waste Plastics into C2 Fuels under Simulated Natural Environments.

Yi Xie,Xingchen Jiao,Kai Zheng,Qingxia Chen,Xiaodong Li,Yamin Li,Weiwei Shao,Jiaqi Xu,Junfa Zhu,Yang Pan,Yongfu Sun

DOI: https://doi.org/10.1002/anie.201915766

2020-01-01

Abstract:Reported here is the first highly selective conversion of various waste plastics into C-2 fuels under simulated natural environment conditions by a sequential photoinduced C-C cleavage and coupling pathway, where single-use bags, disposable food containers, food wrap films, and their main components of polyethylene, polypropylene, and polyvinyl chloride can be photocatalytically transformed into CH3COOH without using sacrificial agents. As an example, polyethylene is photodegraded 100 % into CO2 within 40 h by single-unit-cell thick Nb2O5 layers, while the produced CO2 is further photoreduced to CH3COOH. Various methods and experiments disclose that O-2 and .OH radicals trigger the oxidative C-C cleavage of polyethylene to form CO2, while other investigations show that the yielded CH3COOH stems from CO2 photoreduction by C-C coupling of .COOH intermediates. This two-step plastic-to-fuel conversion may help to simultaneously address the white pollution crisis and harvest highly valuable multicarbon fuels in natural environments.
Bio-oil Fuel Production from Micro Algae by Thermochemical Liquefaction

SUN Jun-nan,ZHANG Jian-an,YANG Ming-de,WU Yu-long

DOI: https://doi.org/10.3321/j.issn:1000-7857.2006.06.008

2006-01-01

Abstract:The use of renewable energy sources is becoming increasingly necessary. Micro algae are of the most common forms of renewable energy. With the advanced genetic technology and thermochemical liquefaction process, bio-oil fuel production from micro algae is an effective approach to solve the energy crisis in future.
Enhanced photocatalytic alkane production from fatty acid decarboxylation via inhibition of radical oligomerization

Zhipeng Huang,Zhitong Zhao,Chaofeng Zhang,Jianmin Lu,Huifang Liu,Nengchao Luo,Jian Zhang,Feng Wang

DOI: https://doi.org/10.1038/s41929-020-0423-3

IF: 37.8

2020-02-01

Nature Catalysis

Abstract:The decarboxylation of bio-derived fatty acids provides a sustainable pathway for the production of alkane products under mild conditions; however, products are generally obtained in low selectivity due to the uncontrollable reactivity of radical intermediates. Here we demonstrate that photogenerated radicals can be rapidly terminated by surface hydrogen species during photocatalytic decarboxylation of fatty acids on a hydrogen-rich surface that is constructed by the interactions between H2 and Pt/TiO2 catalyst, thereby greatly inhibiting oligomerization; Cn–1 alkanes can therefore be obtained from bio-derived C12–C18 fatty acids in high yields (≥90%) under mild conditions (30 °C, H2 pressure ≤0.2 MPa) and 365 nm light-emitting dode irradiation. Industrial low-value fatty acid mixtures (namely, soybean and tall oil fatty acids) can be transformed into alkane products in high yields (up to 95%). Our research introduces an efficient biomass-upgrading approach that is enabled by subtle control of the radical intermediate conversion on a heterogeneous surface.

chemistry, physical
THERMOCHEMICAL CATALYTIC LIQUEFACTION OF MICROALGAE AND PROPERTIES OF BIO-OIL

Shuping Zou,Yulong Wu,Mingde Yang,Zhen Chen,Chun Li,Junmao Tong

DOI: https://doi.org/10.3321/j.issn:0254-0096.2009.11.024

2009-01-01

Abstract:The liquefaction of Dunaliella tertiolecta was investigated in ethylene glycol acidified with H_2SO_4 as catalyst. Mathematical model for predicting the liquefaction yield was set up by central composite design and response surface anal-ysis (RSA) on the basis of one-factor tests. From a regression analysis, it appears that the individual effects, as well as the interactions between operating variables all have significant effects on the liquefaction of Dunaliella tertiolecta. Such effects can be graphically verified through response surfaces and contour line plots. The liquefaction technology was opti-mized as follows: sulfuric acid content of 2.4%, the temperature of 170℃ and the time of 33min. The liquefaction yield reached 97.05% at above-mentioned conditions. To put bio-oil from thermochemical catalytic liquefaction of microalgae into wide application, physical and chemical characteristics of bio-oil were studied in detail and the main compositions of the bio-oil were characterized by FT-IR, GC-MS, ~(13)C-NMR. The major chemical compositions detected were 30.43% benzofuranone, 23.35% fatty acid methyl ester and 27.89% fatty acid hydroxyehtyl ester with long chain from C_(14) to C_(18). Upgrading of bio-oil should be processed further to improve its quality due to its high oxygen content.

Transformation of Triolein to Biogasoline by Photo-Chemo-biocatalysis

Hydrogen Production from Bio-Derived Biphasic Photoreforming over a Raspberry-Like Amphiphilic Ag2O-TiO2/SiO2 Catalyst

Photoenzymatic Production of Next Generation Biofuels from Natural Triglycerides Combining a Hydrolase and a Photodecarboxylase

Transesterification of Methyl Oleate for Sustainable Production of Biolubricant: Process Optimization and Kinetic Study

Lipase and photodecarboxylase co-expression: A potential strategy for alkane-based biodiesel production from natural triglycerides

Recovery Utilization of Triolein for Producing Short Chain Alkane by Combining Biocatalysis and Inorganic Catalysis

Catalytic transformations of acids, aldehydes, and phenols in bio-oil to alcohols and esters

Photothermal technique-enabled ambient production of microalgae biodiesel: Mechanism and life cycle assessment

Catalytic Transformation Of Bio-Oil To Benzaldehyde And Benzoic Acid: An Approach For The Production Of High-Value Aromatic Bio-Chemicals

Converting Glycerol into Valuable Trioses by Cuδ+‐Single‐Atom‐Decorated WO3 under Visible Light

Thermo-chemical Conversion of Chlorella Pyrenoidosa to Liquid Biofuels.

Production and characterization of bio-oil from hydrothermal liquefaction of microalgae Dunaliella tertiolecta cake

Synergistically Photocatalytic Conversion of Two Greenhouse Gases to Liquid‐Phase Oxygenates under Anaerobic Conditions

Continuous hydrocarbon fuels production by photoenzymatic decarboxylation of free fatty acids from waste oils

Research on biocatalyzed artificial photosynthesis

Ultra-sonication application in biodiesel production from heterotrophic oleaginous microorganisms.

Photocatalytic Conversion of Waste Plastics into C2 Fuels under Simulated Natural Environment Conditions

Photocatalyzing Waste Plastics into C2 Fuels under Simulated Natural Environments.

Bio-oil Fuel Production from Micro Algae by Thermochemical Liquefaction

Enhanced photocatalytic alkane production from fatty acid decarboxylation via inhibition of radical oligomerization

THERMOCHEMICAL CATALYTIC LIQUEFACTION OF MICROALGAE AND PROPERTIES OF BIO-OIL