Abstract:Publication date: 28 August 2023 Source: Solid State Phenomena Vol. 348 Author(s): Martin Hartlieb, Jean Claude Tawil, Stephane Bergeron, Per Jansson Structural high vacuum die casting has been growing significantly over the past decades. It is typically done with special (primary type) alloys, special melt treatment practices, high vacuum, a carefully engineered die casting process applying many best practices in our industry. Structural die castings are growing in size and complexity and die casting machines are getting bigger and bigger - and those castings are becoming a significant challenge with current technologies. It was now found that Rheocasting - a process of preparing a semi-solid slurry (with 30-45% solid fraction) that is injected slower and in a laminar way into the cavity, can take structural die casting to completely new heights, enable the casting of parts that would otherwise be impossible to cast and at the same time reduce or eliminate some of the current problems of structural die casting. With Rheocasting, lower purity (secondary) aluminum alloys can be used and excellent properties can be achieved as cast and heat treated (T5, T6/7). Rheocasting has had a breakthrough in the telecom and other industries, but it has now been optimized to become an essential tool in the toolbox of making structural castings. This paper shows the developments that lead to the successful series production of a large (about 4' long) hinge pillar for an Electric Vehicle (EV). It explains the challenges and how they were overcome, and some of the possibilities of the process regarding alloys, heat treatments and achievable properties. It also shows how Rheocasting can help die casters produce more complex (thin and thick walled) and very large castings with the highest integrity. It can replace structural low-pressure permanent mold (LPPM) castings and reduce wall thickness, improve tolerances and make them more economical. Rheocasting can enable die casters to enter this new market of structural castings including Gigacastings, produce parts previously thought impossible to cast (and on much smaller machines than thought), and expand the growing structural die casting market even faster and further.

Towards the Ductility Limit of Large Thin-Walled A356 Alloy Castings

Correlation of Microstructure with Mechanical Properties and Fracture Behavior of A356-T6 Aluminum Alloy Fabricated by Expendable Pattern Shell Casting with Vacuum and Low-Pressure, Gravity Casting and Lost Foam Casting

Numerical Simulation and Experimental Investigation of Microstructure Evolution and Flow Behavior in the Rheological Squeeze Casting Process of A356 Alloy

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Microstructure, segregation and mechanical properties of A356 alloy components fabricated by rheo-HPDC combined with the Swirled Enthalpy Equilibration Device (SEED) process

Towards high performance Al–Si–Fe alloy castings via rheo-diecasting: Effect of injection velocity and heat treatment on microstructure evolution and property

An Experimental Investigation of the Material Properties of the A356 Aluminum Alloy Power Fittings in the Vacuum Die-Casting Process

Experimental Studies on Rheocasting Processing of A356 Alloy

Controlled Cooling of an Aluminum Alloy Casting Based on 3D Printed Rib Reinforced Shell Mold

Mechanical Properties and Fracture Behaviors of a Non-heat-treated Alloy in Varied Regions Within a Megacasting

Effects of Hollow Sand Mold on the Microstructure and Mechanical Properties of a Low Pressure Aluminum Alloy Casting

Innovative Hybrid High-Pressure Die-Casting Process for Load-Bearing Body-In-White Structural Components

A novel rheological high pressure die-casting process for preparing large thin-walled Al–Si–Fe–Mg–Sr alloy with high heat conductivity, high plasticity and medium strength

Producing Structural High Integrity Castings with Minimum Carbon Footprint with the Comptech-Rheocasting Process

Microstructure Evolution and Mechanical Properties' Improvement of NiAl–Cr(Mo)–Hf Eutectic Alloy During Suction Casting and Subsequent HIP Treatment

Investigation of Microstructures and Mechanical Properties of A356 Aluminum Alloy Produced by Expendable Pattern Shell Casting Process with Vacuum and Low Pressure

The Design of 3D-Printed Lattice-Reinforced Thickness-Varying Shell Molds for Castings.

Effects of Process Parameters on Internal Quality of Castings During Novel Casting

Optimization of casting means and heat treatment routines for improving mechanical and corrosion resistance properties of A356-0.54Sc casting alloy

Effect of high cooling rate on the solidification microstructure of Al-Cu/TiB 2 alloy fabricated by Freeze-Ablation casting

Microstructure, Tensile Properties and Fractography of A356 Alloy under As-Cast and T6 Obtained with Expendable Pattern Shell Casting Process