Abstract:Titanium-clad bimetallic steel (TCBS) exhibits outstanding corrosion resistance, and can be advantageously applied in corrosive environments. This study investigated an innovative application of TCBS in cold-formed stub columns. During the cold-forming process, TCBS demonstrated no discernible separation at the bonding interface of the Q235 substrate layer and TA1 cladding layer, indicating the maintenance of synergistic deformation between the cladding and substrate layers. The compressive behavior and ultimate resistance of cold-formed TCBS angle and channel section stub columns were investigated using both experimental and numerical methods. These tests included material tensile flat and corner coupon tests, initial local geometric imperfection measurements, and stub column tests. The stub column test comprised four cold-formed TCBS angle section stub columns and three cold-formed TCBS channel section stub columns covering the non-slender and slender cross-sections. The experimental results were utilized to validate the finite-element (FE) model, which was then used in a parametric study to obtain further numerical data at different cross-sections. A comparative analysis of the ultimate resistance from the tests and numerical analyses with the predicted results from design approaches in EN 1993-1-1, AISI S100, and the direct strength method (DSM) was revealed. The evaluation findings generally showed that the EN 1993-1-1 design method forecasts for cold-formed TCBS channel section stub columns were dangerous. The non-slender cross-section classification coefficient, which was inapplicable to cold-formed TCBS channel steel stub columns, was the primary cause of the above unsafe prediction. As for the design approaches in AISI S100 and DSM for cold-formed TCBS angle and channel section stub columns, as well as those in EN 1993-1-1 for cold-formed TCBS angle section stub columns, they were judged safe but conservative. The above prediction error was mainly caused by ignoring the enhancement in strength properties of the TCBS after the cold-forming process. The considerations mentioned above led to the proposal and demonstration of modifying recommendations that offered safe, accurate, and consistent design approaches to ultimate resistance for the cold-formed TCBS angle and channel section stub columns.

Local Buckling Behaviour of Stainless-Clad Bimetallic Steel Built-Up Square Hollow Section Stub Columns

Stub Column Tests of Thin-Walled Complex Section with Intermediate Stiffeners

Axial Compression Behaviour of Circular Concrete-Filled Stainless-Clad Bimetallic Steel Tubular Stub Columns

Local buckling behaviour of welded I-section steel stub columns with longitudinally profiled steel plates under axial compression: Testing, modelling and design

Local Buckling Behavior of Welded Stub Columns with Normal and High Strength Steels

Experimental investigation of cold-formed stainless steel built-up closed section stub columns

Numerical investigation and design for the local buckling behaviour of high strength steel hexagonal hollow section stub columns under axial compression

Local–overall Interactive Buckling Behaviour of Welded Stainless Steel I-section Columns

Elastic buckling of outstand stainless-clad bimetallic steel plates

Design of Cold-Formed Steel Built-Up Closed Sections with Intermediate Stiffeners

Global Buckling of S35657 Austenitic Stainless Steel Welded Box- and I-section Long Columns under Axial Compression

Overall Buckling Behaviour and Design of High-Strength Steel Welded Section Columns

Seismic Behaviour of Stainless-Clad Bimetallic Steel Welded Box-Section Beam-Columns

Testing and design of cold-formed high strength steel square hollow section columns

Local Buckling of 460mpa High Strength Steel Welded Section Stub Columns under Axial Compression

Local buckling analysis of axially compressed welded box-section stub columns using Q420–Q960 steel

Cold-Formed Steel Built-Up Closed Sections With Intermediate Stiffeners

Experimental and numerical investigations on cold-formed titanium-clad bimetallic steel angle and channel section stub columns

Stub Column Tests on Stainless Steel Built-Up Sections

Numerical study and design of S35657 stainless steel welded stub columns

Simplified design method of cold-formed steel columns with built-up box sections