Abstract:Biomedical sciences facilitated fast detection methods for many diseases recently. The development of this field has led to the dynamic development of Lab-On-a-Chip devices which are portable, require small sample size and have low cost. Fluid manipulation in such bioanalytical systems is a key issue. One of the key features of these devices is the sample preparation which includes the dilution and complete mixing of the analyte with reagents of adequate buffer solution. The mixing possibilities are limited on microscale, since turbulent flow cannot occur due to the dominant viscosity. Chaotic advection can be considered as an ideal mixing method in microfluidic channels as the flows are laminar. The herring-bone like ridges on the channel of the herring-bone type micromixers (Figure 1) act as anisotropic fluid resistance generating secondary transversal flow. The Laminar Flow interface of COMSOL Multiphysics® software was used to solve the velocity field of the micromixer to characterize fluid flow properties. For modelling the mixing phenomena two approaches were used. Mixing by diffusion along the channel was modeled with Transport of Diluted Species interface. To avoid numerical diffusion and high computational cost we used the Particle Tracing module to observe mixing at the level of particles. To optimize the mixing efficiency we conducted a parametric sweep on the thickness of the ridges. Secondary flow and the rotation caused by the herring-bone structure were well observable in the velocity field (Figure 2). The concentration distribution calculated by COMSOL Multiphysics® showed that a high concentration fluid layer was rotated into a low concentration region resulting more surface area for mixing by diffusion. Poincaré map of particle trajectories (Figure 3) showed the layered structure of particle distribution which was similar to the baker's transformation. Modeled herring-bone structures were fabricated in polydimethylsiloxane (PDMS) using multilayer technology. The SU-8 epoxy-based photoresist was applied as molding replica. An improved 3D multilayer formation from SU-8 was developed so that microfluidic systems with high aspect ratio sidewalls and advanced functional parts could be fabricated well. Dye was used for the measurement of mixing by diffusion and yeast cells were used for the particle approach. Pictures were recorded in inverted microscope with bright field imaging. The scattered light from the yeast cells provided good signal (Figure 4). The measurements confirmed the rotation caused by the ridges and also the layered flow characteristics. COMSOL Multiphysics® was used in this study to simulate mixing by diffusion and by secondary flow. Particle tracing model was applied to simulate the mixing of cells in the microchannel. Results agreed well with the measurement, an optimal herring-bone structure was proposed for integration into a bioanalytical system.

Generation of Dynamic Concentration Profile Using A Microfluidic Device Integrating Pneumatic Microvalves

Generation of concentration gradient by controlled flow distribution and diffusive mixing in a microfluidic chip.

Rapid Generation of Spatially and Temporally Controllable Long-Range Concentration Gradients in A Microfluidic Device

Flattening of Diluted Species Profile via Passive Geometry in a Microfluidic Device

Numerical Simulation of the Efficiency of Mixing in Heterogeneous Microchannels with Patterned Surface Potentials

Generation of droplets with adjustable chemical concentrations based on fixed potential induced-charge electro-osmosis

A Versatile Microchannel Array Device for Portable and Parallel Droplet Generation

High-throughput 3D microfluidic chip for generation of concentration gradients and mixture combinations

Electrokinetic Concentration Gradient Generation Using A Converging-Diverging Microchannel

A design and optimization of a high throughput valve based microfluidic device for single cell compartmentalization and analysis

Microfluidic Device for Generating Regionalized Concentration Gradients under a Stable and Uniform Fluid Microenvironment

3-Dimensional Centrifugal Microfluidic Platform for the Generation of Discrete Concentration Gradients

Ultralow and Dynamic Flow Field Generator Composed of Microfluidic Peristaltic Pump

Reconfigurable microfluidic dilution for high-throughput quantitative assays.

Flexible and Rapid Generation of Multiple Concentration Gradients for the Protein Nanoparticle Synthesis

Flexible Concentration Control of Newtonian and Non-Newtonian Fluids in a Microfluidic Device Via AC Electrothermal Flow

Polar coordinate active-matrix digital microfluidics for high-resolution concentration gradient generation

Rapid and steady concentration gradient generation platform for an antimicrobial susceptibility test

A Microfluidic Chip for Rapidly Controlling Dynamic Biochemical Signals.

A Microfluidic Platform Enabling Real-Time Control of Dynamic Biochemical Stimuli to Biological Cells

Optimization of the Herringbone Type Micromixer Using Numerical Modelling and Validation By Measurements