Abstract:An enormous surge in the pavement sector requires the evaluation of interface bonding in asphalt composite, since the assessment of bonding brings considerable cost savings. Microscopic and mechanical analyses were performed to study the status of the interface transition zone of four groups of asphalt mixtures, using thin-slice preparation to obtain asphalt mixture slices with a flat surface for microscopic analysis. The interface transition zones were characterized using good knowledge of blending or diffusion phenomena by conducting tests both at the micro and macro levels to determine mixture quality. Asphalt mixture components were observed using fluorescence microscopy imaging and evaluated by the gray value change law. Asphalt mixture groups, (virgin, recycled of 30% aged and 70% unaged, 6%, and 4% rejuvenator dosage mixtures) under the same process parameters, which are a mixing time of 270 s and a mixing temperature of 150 °C, been considered optimum for component fusion in a hot asphalt mixture were used. This study relied on the influence of morphology law, assessed through rutting tests for high temperature performance, semi-circular bending tests for low temperature performance, and pull-off tests for interface bonding strength. The relationship between interface transition zones and macro performance was studied. The self-developed pull-off method was a research innovation which can be used as an alternative to study interface transition zones in asphalt mixtures, and provides the necessary data needed with 3D surface failure mode calculations. The device measured the bonding strength of a single aggregate in distinct positions using the bitumen penetration test method. The main goals were to determine a correction factor, identify the appropriate alteration, and compute the actual fracture surface area. Using scanning electron microscopy for interface characterization and micro-morphologies of mortar transition zone, our analysis provides adequate knowledge about interface position and the components present. The applied approaches to characterize asphalt mixture interfaces proved workable and reliable, as all methods have similar trends with useful information to determine asphalt pavement quality.

Investigating the effect of preheating conditions and size effect on asphalt blending in recycled asphalt mixture: New approach based on artificial aggregate and laser scanning confocal microscopy

Quantitative evaluation of asphalt blending characteristics in epoxy‐modified hot recycled asphalt mixtures based on 3D confocal fluorescence technology

Quantitative Evaluation of Blending Behavior between Virgin Asphalt and Aged Asphalt Incorporating a New Bio-Based Warm-Mix Rejuvenator

Development of blending model for RAP and virgin asphalt in recycled asphalt mixtures via a micron-Fe 3 O 4 tracer

Investigation of mixing effect and molecular aggregation between virgin and aged asphalt

Influence of RAP Dispersion Characteristics on Mixture Performance

Effect of Mixing Time and Temperature on the Homogeneity of Asphalt Mixtures Containing Reclaimed Asphalt Pavement Material

Analysis of Interface Fusion Effect between Old and New Asphalt under Plant Mixing and Cold Recycling Mode Based on Molecular Dynamics Simulation

Performance Evaluation and Feasibility Study on Reuse of Reclaimed Epoxy Asphalt Pavement (REAP)

Quantifying the agglomeration effect of reclaimed asphalt pavement on performance of recycled hot mix asphalt

Multi-scale performance evaluation and correlation analysis of blended asphalt and recycled asphalt mixtures incorporating high RAP content

Investigating mechanical performance and interface characteristics of cold recycled mixture: Promoting sustainable utilization of reclaimed asphalt pavement

Research on the Influence of RAP and Aged Asphalt on the Performance of Plant-Mixed Hot Recycled Asphalt Mixture and Blended Asphalt

Evaluation on the diffusion-fusion properties and interfacial mechanical behavior of virgin and aged asphalt

The Rejuvenating Effect in Hot Asphalt Recycling by Mortar Transfer Ratio and Image Analysis

Homogeneity Enhancement of Mixtures Containing Epoxy Polymer and 100% Reclaimed Asphalt Pavement

Investigating the interaction between asphalt binder and fresh and simulated RAP aggregate

A comprehensive review on the blending condition between virgin and RAP asphalt binders in hot recycled asphalt mixtures: Mechanisms, evaluation methods, and influencing factors.

Characterization of Interface Transition Zone in Asphalt Mixture Using Mechanical and Microscopic Methods

Performance Characterization of Hot Mix Asphalt with High RAP Content and Basalt Fiber

Interfacial interaction behavior of recycled asphalt pavement: Molecular dynamics simulation