Abstract:The crystallography and structure of the interfaces formed between refined hexagonal close packed (hcp) alpha precipitates and the body centered cubic (bcc) beta matrix in a solution-treated and quenched metastable beta titanium alloy, Ti-5Al-5Mo-5V-3Cr (wt%, Ti-5553), were investigated after heating to 600 degrees C and subsequently aging for 0 and 30 min, respectively. The two phases adopted the classical Burgers orientation, and the observed interfacial structures were analyzed using a topological model, i.e. they contained disconnections, as well as beta crystal lattice dislocations acting as a lattice invariant deformation (LID). The structure of the alpha/beta interface was observed along two mutually perpendicular directions, in high angle annular dark-field scanning transmission electron microscopy (HAADF-STEM). Viewed along the [0001](alpha):[110](beta) directions, an array of disconnections was observed to accommodate the misfit between the alpha and beta crystals. While the spacing of these disconnections varied, the step height associated with them was always twice the {112}(beta) interplanar spacing, and their Burgers vector b was [-0.0190.019 0.034](beta). When the interface was viewed along the [(11) over bar 20](alpha) : [110](beta) direction, in the sample aged for 0 min at 600 degrees C the misfit between the two lattices along [0001](alpha):[110](beta) was so small that no misfit or lattice invariant dislocations were observed within the field of view, in contrast with the interface structure reported in other more conventional titanium alloys. After aging the sample for 30 min, however, the interfacial structure equilibrated, and crystal lattice dislocations were observed on the terrace planes, accommodating the LID, with b = 1/2[(111) over bar](beta). Growth of the alpha precipitates is shown to occur principally by the emission of disconnections from the tip of the existing alpha precipitates into the beta matrix, and its resulting conversion to alpha. These results, combined with analysis using the topological model, show that the nucleation and growth of the hcp alpha phase from the bcc beta matrix in this alloy can be described in terms of the motion of disconnections, accompanied by the displacive diffusion necessary to accommodate the differences in composition between the alpha and beta phases. (C) 2018 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Identification of Prior Β Grains of Additive Manufactured Ti-6Al-4V Alloy Using Electron Backscatter Diffraction

Columnar to Equiaxed Transition During Β Heat Treatment in a Near Β Alloy by Laser Additive Manufacture

Evolution of microstructure and intervariant boundaries of α phase in electron beam melted and heat-treated Ti–6Al–4V alloy

Effective structural unit analysis in hexagonal close packed alloys -- reconstruction of parent beta microstructures & crystal orientation post processing analysis

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

In situ observation of competitive growth of α grains during β → α transformation in laser beam manufactured TiAl alloys

Grain boundary α-phase precipitation and coarsening: Comparing laser powder bed fusion with as-cast Ti-6Al-4V

Parent beta grain reconstruction of globularized Ti-6Al-4V alloy

Effects of the morphology of grain boundary α-phase on the anisotropic deformation behaviors of additive manufactured Ti–6Al–4V

Grain Selection and Growth Orientation of Prior-Β Phase for Ti-6-4 During Additive Manufacturing: Insights from a Modeling Perspective

Structural transformation behavior in a high Nb–TiAl alloy additively manufactured by laser powder bed fusion

Determination of the Structure of Α-Β Interfaces in Metastable Β-Ti Alloys

Using transmission Kikuchi diffraction to characterise α variants in an α + β titanium alloy

Influence of alternate grain boundary α on the development of Widmanstätten microstructure in TC21 Ti alloy

Influences of Deformation Strain, Strain Rate and Cooling Rate on the Burgers Orientation Relationship and Variants Morphology During Β→α Phase Transformation in a Near Α Titanium Alloy

Three-Dimensional Morphological and Crystallographic Investigation of Lamellar Alpha and Retained Beta in A Near Alpha Titanium Alloy by Combination of Focused Ion Beam and Electron Backscattering Diffraction

Controllable Mechanical Anisotropy of Selective Laser Melted Ti6Al4V: A New Perspective into the Effect of Grain Orientations and Primary Grain Structure

In-situ investigation into the deformation behavior of Ti-6Al-4V processed by laser powder bed fusion

Property Improvement of Additively Manufactured Ti64 by Heat Treatment Characterized by In Situ High Temperature EBSD and Neutron Diffraction

Mechanical Anisotropy of Laser Powder Bed Fusion Fabricated Ti-41Nb Alloy Using Pre-Alloyed Powder: Roles Played by Grain Morphology and Crystallographic Orientation

Unravelling heterogeneities in sub-grain cellular structure and micromechanical response of additive manufactured Ti-Nb alloys