Abstract:Functionally gradient material (FGM) fabricating via additive manufacturing draws great attention on alleviating the abrupt material discontinuity at the interface of different materials. Introducing gradient structure into polycrystalline diamond composites to produce diamond/cemented carbide FGM is an effective method to reduce the residual stress and enhance the bonding strength of diamond layer and cemented carbide substrate. However, achieving a smooth transition of material properties from cemented carbide to diamond is challenging. In this research, diamond/cemented carbide FGM with a well-controlled gradient was manufactured via filament-based material extrusion. Initially, green bodies of diamond/cemented carbide FGM were obtained by printing with customized composite filaments. Subsequently, thermal decomposition characteristic of the printing filament was analyzed by TGA, and the influence of different heating rates during the binder decomposition stage on the morphology and structure of the green bodies was investigated. After debinding, diamond/ cemented carbide FGM without flaw was synthesized at 6.5 GPa and 1550degree celsius. Subsequently, microstructure characterization was performed to investigate the distribution characteristics of the materials inside the diamond/cemented carbide FGM. A continuous transition from tungsten carbide to diamond was achieved inside the gradient layer. Furthermore, the stress state of diamond in different positions of the diamond/cemented carbide FGM was analyzed by Raman spectroscopy. It was found that all the residual stresses in the axial interface of the gradient layer were compressive stress, which can prevent occurrence of microcracks resulted from the tensile stresses formed in the interface. Finally, the impact tests reveal that gradient structure is conductive to improving the bond strength between PCD layer and cemented carbide substrate as the impact times before fracture of diamond/cemented carbide FGM has been increased by 15 %. The gradient structure design strategy, generated via the filament-based material extrusion technology, pioneers new ideas to the development of high-performance FGMs in mass production.

Development and Properties Evaluation of Diamond-Containing Metal Composites for Fused Filament Fabrication of Diamond Tool

Development and Printability of Diamond-Containing Composite Filament for Material Extrusion

Influence of Diamond Parameters on Microstructure and Properties of Copper-Based Diamond Composites Fabricated by Fused Deposition Modeling (Fdms)

Influence of diamond parameters on microstructure and properties of copper-based diamond composites manufactured by Fused Deposition Modeling and Sintering (FDMS)

High-strength and wear-resistant Co-Cr-Mo/diamond composites fabricated by selective laser melting

Analysis on the technology of preparing diamond tools by FDMS

Microstructure and performance characterization of Co-based diamond composites fabricated via fused deposition molding and sintering

Studies of Adhesion and Roughness of Diamond Coated Drills and Influence on Cutting Performance

Fabrication and application of CNT fiber-ultra-fine diamond composites via electrophoretic deposition and instantaneous Joule-heating method

Investigation and Formulation of Cobalt Content of Ultra-Thin Diamond Blades and Dicing Performance Manufactured by Fused Deposition Modeling and Sintering (FDMS)

Fabrication of Fe-Based Diamond Composites by Pressureless Infiltration

Development of Diamond-Coated Drills and Their Cutting Performance

Investigation on the machining performance of copper-based diamond ultra-thin dicing blades manufactured by fused deposition modeling and sintering (FDMS)

Simulation, forming process and mechanical property of Cu-Sn-Ti/diamond composites fabricated by selective laser melting

The influence of diamond content on the formability and mechanical properties of additively manufactured metal-bonded diamond tools

Study on Fabrication and Their Cutting Performance of High-quality Diamond-coated Tools with Complicated Shape

Manufacturing and Characterization of Functionally Gradient Material from Cemented Carbide to Diamond Via Filament-Based Material Extrusion 3D Printing

Preparation Technology and Properties of Microtexture Diamond-Coated Tools

Influence of diamond particle size on the properties of diamond/Al composites fabricated by filtration extrusion

Microstructure and performance of glass fiber metal composite-bonded diamond segment with Cu-Sn-Ti alloy

Development of Diamond-Coated Drills for High-Speed Machining SiC Particles Reinforced Aluminum-Matrix Composite