Abstract:Light alloys are being increasingly investigated as alternatives to ferrous-based engineering components, based on weight considerations. However, in-service applications of such light alloy components often require a surface modification step to enhance their wear and corrosion responses for improved functionality. Thermally sprayed cermet coatings offer an enhanced resistance to wear and corrosion. This work investigates WC-CoCr coatings deposited using two different feedstocks comprising fine and coarse powder size distributions on aluminum alloy and steel substrates using high-velocity air-fuel (HVAF) and high-velocity oxy-fuel (HVOF) spray techniques. The WC-CoCr coatings were HVAF sprayed at various parameters to investigate the relationship between the processing conditions, microstructure, and performance. Microindentation, dry sliding wear, dry sand abrasion, cavitation erosion, and corrosion tests were conducted to assess the performance of the coatings. Despite the qualitative similarities in the microstructures of the coatings, the measured microindentation hardness values were observed to vary, and coatings deposited with higher particle impact velocities showed the highest microhardness between 1400 and 1600 HV0.3. For the three categories of wear investigated, the HVAF coatings showed better resistance than the HVOF coating investigated in this study. The estimated average specific wear rate (SWR) due to sliding wear of the HVOF coating was ~ 16.7 ± 4.0 × 10 −8 mm 3 /Nm compared to that of the most resistant HVAF coating, which exhibited a SWR of ~ 1.7 ± 0.6 × 10 −8 mm 3 /Nm. The cumulative mass loss rate due to the abrasive wear on the HVOF coating reached ~ 1.11 mg/min compared to ~ 0.76 mg/min of the most abrasion-resistant HVAF coating. All coatings showed similar corrosion resistances under the investigated conditions. The combination of wear and corrosion performance of the respective coatings could provide insight into the coating selection for intended applications.

Double Layer HVAF-sprayed WC-CoCr Coatings for Optimal Properties

Effects Of Wc Crystal Characteristics On Microstructure And Mechanical Property Of Hvof-Sprayed Wc-Cocr Coatings

Design for Manufacturing of Cemented Carbide Coated Components Toward High Wear and Impact Resistance Performance

Thick WC-12Co Coatings on Bearing Steel Fabricated by Low-Temperature High-Velocity Fuel Spray Process

HVOF Spray Performance Optimization Analysis and Experimental Research of WC–12Co Coating on Ti Alloy

Wear and Corrosion of HVAF and HVOF-Sprayed WC-CoCr Coatings on Aluminum Alloy

Effect of Particle and Carbide Grain Sizes on a HVOAF WC-Co-Cr Coating for the Future Application on Internal Surfaces: Microstructure and Wear

Effect of Cobalt and Chromium Content on Microstructure and Properties of WC-Co-Cr Coatings Prepared by High-Velocity Oxy-Fuel Spraying

Three-Body Abrasive Wear Behavior of WC-10Cr3C2-12Ni Coating for Ball Mill Liner Application

Promising WC-30WB-10Co Cemented Carbide Coating with Improved Density and Hardness Deposited by High Velocity Oxy-Fuel Spraying: Microstructure and Mechanical Properties

Microstructure, Mechanical and Tribological Properties of WC-WCoB Coating

Research on flame characteristics and coating growth process of titanium alloy in HVAF spraying

Effects of structure and processing technique on the properties of thermal spray WC–Co and NiCrAl/WC–Co coatings

An HVOF-Sprayed (Cr3C2-NiCr+Co) Composite Coating on Ductile Cast Iron: Microstructure, Mechanical Properties, and Scratch Resistance

Investigation on Microstructure, Mechanical and Wear Properties of HVOF Sprayed Composite Coatings (WC-Co + CR) On Ductile Cast Iron

Research on microstructure, mechanical property and wear mechanism of AlCoCrFeNi/WC composite coating fabricated by HVOF

A novel design of VAlTiCrCu/WC alternate multilayer structure to enhance the mechanical and tribo-corrosion properties of the high-entropy alloy coating

Sliding friction behaviors of TiCN/Cr 3 C 2 -NiCr and TiCN/WC-CoCr duplex coatings fabricated by combining HVOF and HT-CVD procedures

Microstructure and sliding wear properties of WC-10Co-4Cr coatings on the inner surface of TC4 slender tube by HVOF

Performance evaluation of HVOF sprayed WC-10Co4Cr coatings under slurry erosion

Wear Behaviors of HVAF Sprayed Nano WC-Co Coating Against Al-Ni-Bronze Alloy