Abstract:As computational fluid dynamics (CFD) advances, entropy generation minimization based on CFD becomes attractive for optimizing complex heat-transfer systems. This optimization depends on the accuracy of CFD results, such that accurate turbulence models, such as elliptic relaxation or elliptic blending turbulence models, become important. The performance of a previously developed elliptic blending turbulence model (the SST k-ω-φ-α model) to predict the rate of entropy generation in the fully developed turbulent circular tube flow with constant heat flux was studied to provide some guidelines for using this class of turbulence model to calculate entropy generation in complex systems. The flow and temperature fields were simulated by using a CFD package, and then the rate of entropy generation was calculated in post-processing. The analytical correlations and results of two popular turbulence models (the realizable k-ε and the shear stress transport (SST) k-ω models) were used as references to demonstrate the accuracy of the SST k-ω-φ-α model. The findings indicate that the turbulent Prandtl number (Prt) influences the entropy generation rate due to heat-transfer irreversibility. Prt = 0.85 produces the best results for the SST k-ω-φ-α model. For the realizable k-ε and SST k-ω models, Prt = 0.85 and Prt = 0.92 produce the best results, respectively. For the realizable k-ε and the SST k-ω models, the two methods used to predict the rate of entropy generation due to friction irreversibility produce the same results. However, for the SST k-ω-φ-α model, the rates of entropy generation due to friction irreversibility predicted by the two methods are different. The difference at a Reynolds number of 100,000 is about 14%. The method that incorporates the effective turbulent viscosity should be used to predict the rate of entropy generation due to friction irreversibility for the SST k-ω-φ-α model. Furthermore, when the temperature in the flow field changes dramatically, the temperature-dependent fluid properties must be considered.

The Sstcdgr Model for the Analysis of Turbulent Round Jet Impingement Heat Transfer

Les and Cdns Investigation of T106c Low Pressure Turbine

A developed transition simulation model for turbulent plane jet impingement heat transfer

Validation and Analyses of QCR Correction Turbulence Model in Sub-/Super-sonic Inner Flows

Sensitization of the modified SST model to the swirling and curvature for turbulent impinging jet heat transfer

Application of simplified threeGequation transition model in hypersonic flow

Effects of compressibility correction onγ-Reθ transition model

Computation of Hypersonic Transitional Flows Over Cones Using Gas-Kinetic Scheme Coupled with the Turbulence Model

Analysis of the three-dimensional swirling and non-swirling jet impingement using a turbulence model with cross-diffusion correction

Modelling Of Impinging Flow And Heat Transfer In A Confined Narrow Gap

Numerical Study on Stagnation Point Heat Transfer by Jet Impingement in A Confined Narrow Gap

CFD Prediction for Multi-Jet Impingement Heat Transfer

The effects of rough surfaces on heat transfer and flow structures for turbulent round jet impingement

Numerical Study of Flow and Heat Transfer of Impingement Cooling on Model of Turbine Blade Leading Edge

Numerical Simulation of Turbulence Modulation by Cylindrical Particles in Round Jet

Numerical Study of the Flow and Heat Transfer of a Rectangular-tube Turbulent Impinging Jet Flow

Numerical Study on Heat Transfer of an Impinging Turbulent Plane Jet with Confined Wall.

NUMERICAL INVESTIGATION OF DIFFERENT TURBULENCE MODELS APPLIED IN COMBINED IMPINGEMENT AND FILM COOLING

Effect of the Nozzle Geometry on Flow Field and Heat Transfer in Annular Jet Impingement

Numerical Study of Entropy Generation in Fully Developed Turbulent Circular Tube Flow Using an Elliptic Blending Turbulence Model

Numerical Prediction of Transitional Features of Turbulent Forced Gas Flows in Circular Tubes with Strong Heating