Abstract:High-strength aluminium alloys are increasingly popular and gaining more prominence in structural engineering. The global buckling behaviour and design of high-strength aluminium alloy circular hollow section (CHS) columns subjected to axial compression are investigated in this study. Ten experiments on CHS specimens with two extruded 7A04-T6 CHS profiles - 165 x 15 and 165 x 7.5 (in mm), were conducted. The material tests and initial geometric imperfection measurements were carried out prior to column tests. The test setup, procedure and results, including failure modes, ultimate resistances and load-displacement curves were comprehensively reported and analysed. Based on the developed and validated finite element (FE) models, an extensive parametric study, over a broad range of member and cross-section slenderness as well as the strain hardening exponents and proof strengths of the high-strength aluminium alloy material, was performed to complement the test data pool. The applicability of current buckling design provisions used for normal-strength aluminium alloy columns in the European, Chinese, American, Australian & New Zealand standards and the proposal of Rasmussen and Rondal to 7A04-T6 high-strength aluminium alloy CHS columns was evaluated through comparisons with the test and FE results. The results show that the European, Chinese and American standards provide conservative buckling resistance predictions, while the Australian & New Zealand standard and Rasmussen's proposal generally yield unsafe capacity predictions. Finally, two flexural buckling curves within the framework of the EN 1999-1-1:2007 design method, featuring a revised linear imperfection term and a newly developed hybrid linear-nonlinear imperfection term, were proposed accordingly, and were shown to provide more accurate and consistent buckling resistance predictions.

Flexural Buckling of Extruded High-Strength Aluminium Alloy SHS Columns

Experimental and Numerical Study of 7A04-T6 Extruded Aluminium Alloy Lipped Angle Columns in Axial Compression

Flexural Buckling of High-Strength Aluminium Alloy CHS Columns

Behaviour and Design of Extruded High-Strength Aluminium Alloy SHS Beam-Columns

Testing, Modelling and Design of 7A04-T6 High-Strength Aluminium Alloy RHS Columns under Axial Compression

Axial Compression Behaviour of 7A04-T6 High-Strength Aluminium Alloy SHS and RHS Stub Columns

Testing and Design Methods for High-Strength Aluminium Alloy CHS Members under Combined Axial Compression and Bending

Experimental and Numerical Study of Fixed-Ended High-Strength Aluminum Alloy Angle-Section Columns

Flexural Behaviour of 7A04-T6 High-Strength Aluminium Alloy SHS and RHS Beams under Moment Gradient

Testing, Modelling and Design of Aluminium Alloy Single-Angle Members Connected by One Leg under Eccentric Compression

Experimental study and parametric analysis on the stability behavior of 7A04 high-strength aluminum alloy angle columns under axial compression

Local buckling and postbuckling strength of extruded aluminium alloy stub columns with slender I-sections

Study of Local Buckling Performance of 7075-T6 High-Strength Aluminium Alloy H-section Stub Columns

Stability and Design of High-Strength Aluminium Alloy RHS Members under Eccentric Compression

7A04-T6 High-Strength Aluminium Alloy SHS and RHS Beams under Pure Bending—testing, Modelling and Design Recommendations

Experimental Investigation and Numerical Analysis of Pin-Ended Extruded Aluminium Alloy Unequal Angle Columns

Testing and design of cold-formed high strength steel square hollow section columns

Study on the local buckling behavior of high strength aluminium alloy angle columns under axial compression

Design of Austenitic and Duplex Stainless Steel SHS and RHS Beam-Columns

Residual compressive behavior of 6063-T5 aluminium alloy SHS and RHS stub columns

Behavior and Design of Slender Concrete-Filled Wide Rectangular Steel Tubular Columns under Axial Compression