Abstract:Keeping water clean is of vital significance for human health and environmental protection. In order to remove organic micro-pollutants and natural organic substances in water bodies and kill pathogenic microorganisms simultaneously, this study synthesized a multifunctional porous β-cyclodextrin polymer with a high specific surface area by introducing quaternary ammonium groups and rigid benzene rings, respectively, which was then polymerized with crosslinking agent-4,4′-bis (chloromethyl)-1,1′-biphenyl (BCMBP) in an ionic liquid system. The grafting of quaternary ammonium groups was beneficial for the removal of negative-charged humic acid (HA) and sterilization. The introduction of numerous rigid structures during benzylation and Friedel-Crafts alkylation reaction could significantly improve the porosity and specific surface area of the polymer, conducive to the exposure of cyclodextrin binding sites and contaminant adsorption. By changing the proportions of quaternization and benzylation, the structure and surface properties of the polymer could be adjusted, thus further regulating the adsorption performance. Compared with activated carbon, the polymer named BQCD-BP with a huge surface area of 1133 m 2 g −1 prepared under optimized conditions showed outstanding adsorption performance and sterilization ability. The pseudo-second-order kinetic constant of BQCD-BP reached 1.2058 g·mg −1 ·min −1 , which was approximately 50 times greater than that of activated carbon (0.0256 g·mg −1 ·min −1 ) under the same experimental condition. The adsorption capacity of BQCD-BP to HA was twice as high as that to AC, and the antibacterial ability of BQCD-BP was significant, achieving 90% at the dosage of 1g L −1 . Moreover, the adsorption process was hardly affected by the hydrochemical conditions, and the polymer was easy to regenerate. In addition, the excellent adsorption and antibacterial performance of the polymer were also identified by natural water treatment. COD was almost completely removed, and the removal efficiency of TP reached 92% after contact with BQCD-BP. The sterilization rate of BQCD-BP to viable bacteria in complex water bodies reached 82%. Undoubtedly, BQCD-BP is a potential multifunctional water treatment material with reasonable design in the actual water purification.

Cucurbit[5]uril-based Porous Polymer Material for Removing Organic Micropollutants in Water

Rapid, Complete Removal Of Organic Pollutants From Water By A Sns2-Modified Porous -Cyclodextrin-Containing Polymer

Achievements in Preparation of Cyclodextrin–Based Porous Materials for Removal of Pollutants

Multifunctional porous β-cyclodextrin polymer for water purification

Porous calix[4]pyrrole-based polymers with high surface area for efficient removal of polar organic micropollutants from water

The synthesis of a DMpillar[5]arene-based porous polymer with ultrafast adsorption rate and high adsorption capacity for organic micropollutants from water

Porous pillararene-based polymer as adsorbent and solid disinfectant for water treatment

A Crosslinked Β-Cyclodextrin Polymer Used for Rapid Removal of a Broad-Spectrum of Organic Micropollutants from Water.

Post-crosslinking of conjugated microporous polymers using vinyl polyhedral oligomeric silsesquioxane for enhancing surface areas and organic micropollutants removal performance from water

Nitrogen-rich triazine-based porous polymers for efficient removal of bisphenol micropollutants

Multifunctional Β-Cyclodextrin Polymer for Simultaneous Removal of Natural Organic Matter and Organic Micropollutants and Detrimental Microorganisms from Water.

A silsesquioxane-porphyrin-based porous organic polymer as a highly efficient and recyclable absorbent for wastewater treatment

Adaptive tetralactam macrocycle based polymers for efficient and rapid removal of organic micropollutants with wide scope

Efficient and rapid removal of typical phenolic compounds from water with biobased porous organic polymers

Porous β-cyclodextrin nanotubular assemblies enable high-efficiency removal of bisphenol micropollutants from aquatic systems

Construction of tunable pyrylium based porous ionic polymer network for efficient waterborne pollutant treatment

Adsorptive behaviors and mechanisms for removing three organic pollutants from aqueous solutions by polyvinyl alcohol/porous carbon composite hydrogels

Sulfonate-Bonded Conjugated Microporous Polymer Hollowed-Out Spheres to Capture Fluoroquinolone Antibiotics and Cationic Dyes from Wastewater

Cationic Porous Organic Polymers As an Excellent Platform for Highly Efficient Removal of Pollutants from Water

Hierarchically Micro-Mesoporous Β-Cyclodextrin Polymers Used for Ultrafast Removal of Micropollutants from Water.

Porous multifunctional phenylcarbamoylated-β-cyclodextrin polymers for rapid removal of aromatic organic pollutants