Abstract:With the rapid development of material science, the original aluminum alloy shield structure of spacecraft has been gradually replaced by sandwiched structure of carbon fiber reinforced resin matrix composite structure with aluminum honeycomb. In order to reveal the damage characteristics induced by debris impacting on shield structure of spacecraft and aiming at the engineering requirements that spacecraft undergo alternately high and low temperature environment during on-orbit operation, CFRPs/aluminum honeycomb core sandwich shield structure is used as the impact object. The damage characteristics of 2A12 aluminum projectile impacting on CFRPs/aluminum honeycomb sandwich structure with different aluminum honeycomb arm lengths at different impact velocities are studied by using the high and low temperature system for the target and the loading system of two-stage light gas gun. The experimental results show that the arm lengths of aluminum honeycomb have little effect on the perforation area of front and rear surfaces of CFRPs/aluminum honeycomb sandwich structure at high temperature, but the impact speed has a great effect on the perforation areas of front and rear surfaces of rear panels. The lower the impact speed is, the smaller the perforation diameter is. The deformation and ablation areas of the front and rear surfaces of the aluminum honeycomb increase with the increasing of the arm length of the aluminum honeycomb. At the same time, the physical quantities mentioned above have similar changes in low temperature environment. The fitting formulas, such as the relationships among perforations of the front and rear surfaces of CFRP and the arm lengths of aluminum honeycomb, and ablation area of aluminum honeycomb and the arm lengths of aluminum honeycomb are given at the given experimental conditions. The micro-morphology and damage characteristics of the panels and aluminum honeycomb are analyzed at the different locations near the impact point at high temperature.

Experimental Study of the High-Power Laser Resistance of Ablative Material-Filled Sandwich Panels with Truss Cores under Hypersonic Airflow

Instantaneous Ablation Behavior of Laminated CFRP by High-Power Continuous-Wave Laser Irradiation in Supersonic Wind Tunnel

Carbon nanotube sponges filled sandwich panels with superior high-power continuous wave laser resistance

Modeling the high temperature behavior of all-composite, corrugated-core sandwich panels undergoing ablation

Thermal response during volumetric ablation of carbon fiber composites under a high intensity continuous laser irradiation

Experimental Investigation on Ablation Behaviors of CFRP Laminates in an Atmospheric Environment Irradiated by Continuous Wave Laser

Study on the Multi-Field Coupling Behavior of C/SiC Composites under the Combined Action of the Local Extreme Heat Source and Hypersonic Airflow

Study on the Ablation Behavior of C/SiC Composite Materials under the Action of Local Structural Thermal Sources

Laser Ablation Behavior of C/SiC Composites Subjected to Transverse Hypersonic Airflow

Experimental Study on Damage Characteristics of CFRPs/Aluminum Honeycomb Sandwich Structure Impacted by Ultra-High Speed Under High and Low Temperatures

Preliminary Tests of Non-Ablative Thermal Protection Materials

Carbon fiber reinforced ZrC based ultra-high temperature ceramic matrix composite subjected to laser ablation: Ablation resistance, microstructure and damage mechanism

Experimental And Numerical Evaluation Of The Ablation Process Of Carbon/Carbon Composites Using High Velocity Oxygen Fuel System

Experimental study on failure mechanisms of sandwich panels with multi-layered aluminum foam/UHMWPE laminate core under combined blast and fragments loading

Numerical simulation of continuous laser microdrilling of ultrathick aluminum honeycomb sandwich panels

Decoupling Mechanisms of "avalanche" Phenomenon for Laser Ablation of C/SiC Composites in Hypersonic Airflow Environment

Microstructure Evolution and Ablation Mechanism of C/C and C/C‐SiC Composites Under a Hypersonic Flowing Propane Torch

Microstructure and ablation behaviour of C/C-SiC-ZrC-Cu composites prepared by reactive melt infiltration

Thermostructural Responses of Metallic Lattice-Frame Sandwich Structure for Hypersonic Leading Edges

Research on test method for ablation properties of ablative materials

Ablation Mechanism and Properties of Silica Fiber-Reinforced Composite Upon Oxyacetylene Torch Exposure