Abstract:In this research, a three-dimensional (3D) transient finite element model based on a sequentially coupled thermal–mechanical analysis (SCTMA) is proposed to simulate the evolution of the temperature field and stress field as well as the cladding geometry of the Ni60A-25 % WC laser cladding composite coating. Based on the thermo-physical properties of Ni60A-25 % WC powder and the design of the double ellipsoidal heat source model, a 3D finite element model of double-layer laser cladding with two channels is established. The evolution of the temperature field and the residual stress field at different laser process parameters are investigated to evaluate the quality of the cladding layer. The impact of different laser cladding process parameters on the cladding dimensions is investigated. The dimensions of the simulated molten pool are analyzed by fitting a polynomial curve. The simulation results show that the laser power is proportional to the temperature, and the temperature growth rate of the coating is significantly higher than that of the substrate. The scanning speed is inversely proportional to the temperature. The maximum temperature of the cladding is 1.5 times the maximum temperature of the substrate. The temperature growth rate of the cladding layer is twice that of the substrate. Due to the asymmetry of the heat source in the multi-pass cladding process, the laser energy absorption rate is not the same on both sides of the melted layer. The double ellipsoidal heat source model has a larger diffusion range in the un-melted powder, resulting in asymmetry in the width direction of the cladding layer. The analysis of the residual stresses in the cladding layer shows that the residual compressive stresses in all paths increase with the increasing laser power. The normal x residual compressive stress in the coating and the maximum residual compressive stress occur at the end of the laser beam scan. The residual compressive stress in all paths decreases as the scanning speed increases. The results show that the dimensions of the molten pool are proportional to the laser power and inversely proportional to the scanning speed. The cladding geometry can be calculated with polynomial fitting equations at a selected laser power (500 W–2800 W) and scanning speed (1 mm/s–8 mm/s). The error analysis of the simulation and the experimental results can validate the proposed finite element simulation model. The error in the molten pool size is less than 20 % for the simulation and experimental results.

Characterization of Elastic Modulus of Laser Cladding Coatings Using Laser Ultrasonic Method

Measurement of elastic modulus of laser cladding coatings by laser ultrasonic method

Nondestructive measurement of the grain size of laser cladding coatings using a laser ultrasonic method

Differential analysis of the influence mechanism of ultrasonic vibrations on laser cladding

Temperature Field Simulation and Experimental Analysis of Laser Cladding 45 Steel.

Acquisition of heterogeneous constitutive relationship of Ni60 laser cladding layer based on nano-indentation experiment

Analysis of the sequentially coupled thermal–mechanical and cladding geometry of a Ni60A-25 %WC laser cladding composite coating

Effect of ultrasonic impact treatment on surface stress evaluation of laser cladding coating by using critically refracted longitudinal wave

Off-epicentral measurement of laser-ultrasonic shear-wave velocity and its application to elastic-moduli evaluation

Application of Laser Cladding Technology to Improve the Interface of Thermal Barrier Coatings

Quantitative analysis and experimental study of the influence of process parameters on the evolution of laser cladding

Research on the temperature rise mechanism of ultrasonic field-assisted laser cladding

Research of On-Line Monitoring Technology Based on Laser Triangulation for Surface Morphology of Extreme High-Speed Laser Cladding Coating

Progress and Challenges of Ultrasonic Testing for Stress in Remanufacturing Laser Cladding Coating

Numerical Simulation and Experimental Analysis of Thermal Conduction and Stress in Laser Cladding Repair of Thin-Walled Parts

Preparation and the Mechanical and Tribological Properties of Laser Cladding Coating

Thermal expansion control of composite coatings on 42CrMo by laser cladding

Numerical simulation and experimental study on the evolution of multi-field coupling in laser cladding process by disk lasers

Numerical simulation method of the multi-field coupling mechanism for laser cladding 316L powder

Laser-induced ultrasound imaging of multi metal laminate with complex interface

Nondestructive characterization of mechanical properties on metallic and polymer plates using hybrid laser-air coupled ultrasonic techniques