Abstract:All solid state batteries are widely investigated as next generation batteries because they do not suffer from leakage, volatilization, and flammability of liquid electrolyte. Both bulk type and thin film solid batteries have attract great attention. LiCoO2 thin film has been commonly used as the cathode material for solid state batteries due to its high capacity, operating voltage and long cycle life. Because of the importance of the solid-solid interface for the performance of the battery and stability during cycling, i.e. its life time, the interface of substrate/LiCoO2 and LiCoO2/solid electrolyte during the preparation of the solid battery and possible intermediate products in the interlayer attract great attention recently. [1] The deposition parameters has a big influence on the film quality in terms of structure, morphology and electrochemical properties. In the case of layered LiCoO2, lithium-ion diffusion rely on vacancy hopping mechanism within the lithium plane, showing a predominant two dimensional path. Therefore, different orientation of lattice could influence the intercalation properties of LiCoO2 thin film deposited. [2] A primary challenge in all solid state battery is the difficulty of rapidly moving charge across solid/solid interface within the electrodes and across the electrode/electrolyte interface. The consecutive study on electrode and/or electrolyte has achieved great progress for the last decades. However, interfaces still dominate the interfacial impedance during electrochemical reaction. The optimization of interface of substrate/LiCoO2 and LiCoO2 /solid electrolyte could direct the further improvement of current all solid state batteries. Both lithium ion mobility and electrochemical reaction of LiCoO2 thin film with the solid electrolyte and the substrate are related to the interfacial resistance, which could be minimized through controlling growth orientation of LiCoO2during deposition.[3] Therefore, the ionic transportation across solid/solid interface and electrode/electrolyte interface are increased, leading to improved electrochemical performance. In this work, we optimize the deposition parameter to get high crystalline HT-LiCoO2 with hexagonal structure and good electrochemical performance firstly. Next, we study on sputtering deposition of LiCoO2 with different orientation in order to study the LiCoO2/substrate and LiCoO2/solid state electrolyte interface. The compositional (XPS), microstructural (XRD, Raman, SEM) and electrochemical properties of the sputtering LiCoO2thin films with different orientation are investigated. For the study of interface, we will adopt advanced technique to investigate the chemical/physical changes at the interface layers. Reference [1] Luntz, Alan C., et al. The journal of physical chemistry letters 6.22 (2015): 4599-4604. [2] Bates, J. B., et al. Journal of The Electrochemical Society 147.1 (2000): 59-70. [3] Yoon, Yongsub, et al. Journal of Power Sources226 (2013): 186-190.

Preferential Growth of HT-LiCo1-xAlxO2 Cathode Micro-Bricks Via an Intermediate-Facilitated Solid-Solid-gas Reaction

Rational Synthesis of High-Performance Ni-rich Layered Oxide Cathode Enabled Via Probing Solid-State Lithiation Evolution

Chemical and structural evolution during solid-state synthesis of cobalt-free nickel-rich layered oxide cathode

One-Step Synthesis of Stoichiometric LiNi 0.80 Co 0.15 Al 0.05 O 2 Precursor in Acidic Environment and Its Facile Growth into Single Crystals at Low Temperatures for Li-Ion Batteries

Enhanced Li-ion Intercalation Kinetics and Lattice Oxygen Stability in Single-Crystalline Ni-rich Co-poor Layered Cathodes

Synthesis of Monodisperse and Discrete Ultra-High Nickel LiNi0.97Co0.02Mn0.01O2 Octahedral Single Crystals via Single Crystal Intermediates for Li-Ion Batteries

Synthesis and Properties of Single-Crystal Ni-rich Cathode Materials in Li-ion Batteries

Simple Strategy for Synthesizing LiNi 0.8 Co 0.15 Al 0.05 O 2 Using CoAl-LDH Nanosheet-Coated Ni(OH) 2 as the Precursor: Dual Effects of the Buffer Layer and Synergistic Diffusion

Surface Atomic Rearrangement with High Cation Ordering for Ultra-Stable Single-Crystal Ni-Rich Co-Less Cathode Materials

A new surface phase of Al2Ti7O15 to enhance the electronic conductivity and interfacial stability of LiCoO2 cathode materials

Gospel for Improving the Lithium Storage Performance of High-Voltage High-Nickel Low-Cobalt Layered Oxide Cathode Materials.

Mitigating Lattice Distortion of High-Voltage LiCoO2 via Core-Shell Structure Induced by Cationic Heterogeneous Co-Doping for Lithium-Ion Batteries

Co‐doping of Al3+ and Ti4+ and electrochemical properties of LiNiO2 cathode materials for lithium‐ion batteries

One-Step Synthesis of a Single-Crystal LiNi 0.83 Co 0.11 Mn 0.06 O 2 Cathode with Excellent Electrochemical Properties by Ti 4+ Doping and LiTi 2 O 4 In Situ Chemical Coating Using a Novel Variable Temperature Sintering Process

Impact of Lithium Sources on Growth Process and Structural Stability of Single‐Crystalline Li‐rich Layered Cathodes

Improving diffusion kinetics and phase stability of LiCoO2 via surface modification at elevated voltage

Control of Lattice Orientation and Interface of LiCoO2 for All Solid State Batteries

Insights on the Activation and Stabilization of NCA Cathode Interface: Surface Chemical State Modulations of Aluminum-Mediated Li 0.73 CoO 2 Coatings

Atomic Insight into the Layered/Spinel Phase Transformation in Charged LiNi0.80Co0.15Al0.05O2 Cathode Particles

In Situ Probing and Synthetic Control of Cationic Ordering in Ni‐Rich Layered Oxide Cathodes

Structure/Interface Coupling Effect for High‐Voltage LiCoO<sub>2</sub> Cathodes